National Instruments NI 9265 User manual

GETTING STARTED GUIDE

NI 9265

4-Channel, 0 mA to 20 mA, 16-Bit Analog

Output Module

This document explains how to connect to the NI 9265.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9265. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9265 only as described in this document.

Caution Do not operate the NI 9265 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

2| ni.com | NI 9265 Getting Started Guide

Safety Voltages

Connect only voltages that are within the following limits.

Channel-to-COM or

Vsup-to-COM

±40 V maximum1

Isolation Voltages

Channel-to-channel None

Channel-to-earth ground, Vsup-to-earth ground, or

COM-to-earth ground

Continuous

up to 2,000 m altitude 250 Vrms,

Measurement Category II

up to 5,000 m altitude 60 VDC,

Measurement Category I

1The maximum voltage that can be applied between any channel or Vsup

terminal and a COM terminal without damaging the module or other devices.

NI 9265 Getting Started Guide | © National Instruments | 3

Withstand

up to 2,000 m altitude 2,300 Vrms, verified by a 5 s

dielectric withstand test

up to 5,000 m altitude 1,000 Vrms, verified by a 5 s

dielectric withstand test

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Measurement Category II is for measurements performed on

circuits directly connected to the electrical distribution system.

This category refers to local-level electrical distribution, such as

that provided by a standard wall outlet, for example, 115 V for

U.S. or 230 V for Europe.

4| ni.com | NI 9265 Getting Started Guide

Note Do not connect the NI 9265 to signals or use for

measurements within Measurement Categories III or

IV.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the device, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk voltage or 60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Ensure that devices and circuits connected to

the module are properly insulated from human contact.

Caution When module terminals are hazardous

voltage LIVE (>42.4 Vpk/60 VDC), you must ensure

that devices and circuits connected to the module are

properly insulated from human contact. You must use

the NI 9927 connector backshell kit to ensure that the

terminals are not accessible.

NI 9265 Getting Started Guide | © National Instruments | 5

Safety Guidelines for Hazardous Locations

The NI 9265 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9265 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

6| ni.com | NI 9265 Getting Started Guide

Caution For Division 2 and Zone 2 applications,

connected signals must be within the following limits.

Capacitance 80 nF max max

Inductance 0.2 H max max

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9265 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 03 ATEX 0324020X and is

IECEx 14.0089X certified. Each NI 9265 is marked II 3G and

is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9265

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

NI 9265 Getting Started Guide | © National Instruments | 7

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product

documentation.

8| ni.com | NI 9265 Getting Started Guide

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance

is attained.

NI 9265 Getting Started Guide | © National Instruments | 9

Preparing the Environment

Ensure that the environment in which you are using the NI 9265

meets the following specifications.

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

Operating humidity

(IEC 60068-2-78)

10% RH to 90% RH,

noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals

for complete specifications.

Connecting the NI 9265

The NI 9265 provides connections for four analog output

channels.

10 | ni.com | NI 9265 Getting Started Guide

Other manuals for NI 9265

Table of contents

Other National Instruments Control Unit manuals

National Instruments

National Instruments NI-9361 Manual

National Instruments

National Instruments NI 9269 User manual

National Instruments

National Instruments NI 9469 User manual

National Instruments

National Instruments FlexRIO PXI-79 R Series User manual

National Instruments

National Instruments NI-9206 User manual

National Instruments

National Instruments PXIe-5693 User manual

National Instruments

National Instruments 6589 User manual

National Instruments

National Instruments FlexRIO PXIe-7975R User manual

National Instruments

National Instruments NI PXI-6682 User manual

National Instruments

National Instruments 9861 User manual

National Instruments

National Instruments NI PXIe-4138 User manual

National Instruments

National Instruments NI PCIe-1430 User manual

National Instruments

National Instruments NI TB-4340 User manual

National Instruments

National Instruments NI 9201 User manual

National Instruments

National Instruments PXIe-8521 User manual

National Instruments

National Instruments NI 9852 User manual

National Instruments

National Instruments NI 9871 User manual

National Instruments

National Instruments PXI Terminal Block NI TB-2708 User manual

National Instruments

National Instruments Module SCXI-1125 Manual

National Instruments

National Instruments PXIe-8830mc User manual

National Instruments

National Instruments PCIe-7858 User manual

National Instruments

National Instruments NI 9227E User manual

National Instruments

National Instruments NI PXI-8840 User manual

National Instruments

National Instruments Network Adapter NI PXIe-6672 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual