muscle CM2 User manual

Integrated AC Servo System
MDUG-CM2/17301E-01

PR-001
Before use, read through this User's Guide to ensure proper use.
In particular, be sure to read "Instructions for Safety" without fail for safety purpose.
Keep this User's Guide at an easily accessible place so as to be referred anytime as necessary.
The contents of this User's Guide are subject to change without notice for the improvement in product,
specication, or usability of this User's Guide.
This User's Guide is only intended to provide information about the product, and dose not guarantee any
results from usage of the product. MUSCLE CORPORATION is not responsible for any damages and/or
injuries resulting from the implementation in accordance with the contents of this User's Guide.
Please notify our sales representative if you have some questions or comments with the contents of this
User's Guide.
The contents of this User's Guide do not guarantee or grant rights to patents, copyright, or any other rights to
the intellectual property of MUSCLE CORPORATION or any third party. MUSCLE CORPORATION is not
responsible for any problems that may occur concerning the intellectual property rights of third parties
resulting from the application of information provided in this User's Guide.
COOL MUSCLE is a registered trademark of MUSCLE CORPORATION.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other
countries.
Other company names and product names described in this User's Guide are trademarks or registered
trademarks of their respective holders. The trademark notices (TM, ®) are not necessarily appended to
company, system, and product names described in this User's Guide.
Please refer to the related manuals, "CML User's Guide" for parameter settings, programmings, COOL
MUSCLE operation and operation language "CML(COOL MUSCLE language)" and "COOL WORKS LITE
USER'S MANUAL" for the usage of COOL WORLS LITE, a communication software for COOL MUSCLE
operation.
© 2007 MUSCLE CORPORATION. All rights reserved.
It is prohibited to reprint or copy all or any part of this User's Guide without prior written permission.

PR-002
Instructions for Safety
【Be sure to read before use for safety】
To ensure safe use
To ensure the safe and proper use of our products, it is important that you read this User's Guide thoroughly
prior to its use. Failure to read, fully understand and implement following instructions and precautions may
result in damage to the product, the machine to which it is installed, or operator injury.
About product application
These products are manufactured as a general-purpose part for the application in general industries.
They are not designed or manufactured for equipments or systems which affect human life or applications in
which faulty operation or failure may result in personal injury or signicant damage to property.
These products shall not be used in applications which require an extremely high degree of reliability and
safety, such as those listed below.
Medical equipment or system that have a direct affect on human life.
Applications that directly affect on the safety of people.
(For example, the operation and control of aircraft, cars, elevators railroads, etc.)
Applications in which failure may signicantly damage or impact the society and public.
(For example, nuclear power, electric power, aerospace, public transportation system, etc.)
Equipments or systems used under special environmental condition.
Applications with the same level of importance as those described above.
* When considering the product for use in such special applications, please contact our sales representative.
We ask that you employ fail-safe systems when applying these products to the equipment in which any
failure on its part can be expected to cause a serious accident or loss.
Safety Precautions
Please read following precautions in order to ensure safe and proper use of the product, and avoid dameges
on machinery and injuries to the operators and other people.
This User's Guide should carefully be kept in a convenient place for the operator's easy reference.
In this User's Guide, safety precautions are classied as either “Warning” or “Caution”, indicating the level of

PR-003
hazard seriousness possibly occurred when handling the product incorrectly.
The symbols are explaind below.
Note that some items described as Cautions may result in more serious damage under certain
conditions. Please observe the precautions of both levels because they are important to personnel safety.
“What must not be done” and “What must be done” are indicated by the following symbols.
Indicates a potentially hazardous situation which, if not handled
properly, may result in injury or property damage.
Indicates an imminently hazardous situation which, if not handled
properly, may result in death or serious injury.
Warning
Caution
Ex. "No disassemble"
Indicates a prohibited action
(what must not be done).
Indicates a necessary action
(what must be done). Ex. "Grounding"

PR-004
Warning
Never touch the rotating part of the motor while operating.
The failure could result in injuries.
Take a measure for safety to keep away contact by personel.
Do not touch the motor and driver while power is ON or for some time after
power-OFF.
Temperatures may be high and you may get burnt.
Do not change the wiring while power is ON.
Be sure to remove wiring and unplug a connector after power-OFF.
The failure could result in electric shocks, runaway or damages.
Do not give damage to, apply excessive force to, place something heavy upon,
or pinch the cable.
Do not pull the cable by too much power. The failure could result in damages to connection
section, or electric shocks.
Never disassemble, modify, or repair the product.
Do not open the cover of the product, or disassemble or modify the parts inside.
The failure could result in re, electric shocks, malfunction or injuries.
Do not install the product on or near combustibles.
Attach the product to noncombustible matter such as metal. The failure could result in re.
Do not tamper with water, corrosive gas, inammable gas, ammable
material, or electrically conductive material such as screw or metal piece.
Do not insert metal pieces into the venting holes of enclosure.
The failure could result in re, electric shocks, or damages.
Be sure to ground the terminal of the earth wire.
Securely ground to prevent electric shocks and to stabilize the potential in the control circuit.
Caution (environment)
Keep or use the product under the following environmental conditions.
Ambient temperature / Working : 0 to 40 , Storage : -20 to 60 (non freezing)
Ambient humidity : Below 90%RH (non condensing)
Vibration / Shock resistance : Below 9.8ms-2 (1G) / Below 98ms-2 (10G)
Avoid store or use in such an environment where the product is exposed to oil or water.
(It is not waterproof structure.)
Indoor use only (no direct sunlight). No corrosive gas, inammable gas, oil mist or dust.

PR-005
Caution (transportation)
The product is precision mechanical equipment.
Do not drop or give any strong impact to the product.
The failure could result in damages or malfunction.
Do not hold the cables or motor shaft when transporting the product.
The failure could result in damages or malfunction.
Do not climb, stand, or put heavy objects on the product.
The failure could result in damages or malfunction.
Do not stack in excess of the specied number of products.
The failure could result in damages or malfunction.
Caution (installation)
When installing a pulley or coupling to the machine, do not hammer on
the motor shaft.
The failure could result in damages or malfunction.
Be sure to x the product on the machine rmly.
If xation is not tight enough, the product may come off while operating.
Be sure to make precise centering between the motor shaft and the machine.
Deviation from the center could result in vibration or damages.
The load inertia moment should be below the recommended load inertia
moment ratio of the motor being used.
If it is too large, desired performance may not be attainable.
Carefully consider the heat radiation of the product, and make sure to
install it in the condition with proper airow.
Be sure to avoid interference with the heat radiation of motor and driver.

PR-006
Caution (wiring)
Wiring must always be performed properly and reliably.
Ensure that terminal connection or polarity (+, -) is correct.
The failure could result in damages or malfunction.
Carefully consider the cable clamping method, and make sure that bending
stress and the stress of the cable’s own weight are not applied on the cable
connection section.
The failure could result in damages or bursts.
Do not apply a voltage exceeding the specied voltage to the input terminal.
The failure could result in damages or bursts.
Do not modify the connector or terminals, etc., on the end of the cable.
The failure could result in damages or bursts.
Caution (usage)
Provide an external emergency stop circuit to ensure that operation can be
stopped and power switched off immediately.
When a trouble occurs, shut off the power immediately.
Before operation, check the parameter settings to ensure that there are no
operation errors. Connect a load to the products after the successful
trial-operations.
Improper settings may cause some machines to perform unexpected operation,
resulting in damages.
Do not apply a load exceeding the tolerable load onto the motor shaft.
The failure could result in break of the shaft.
Do not turn on or off the power frequently.
The failure could result in degradation of circuit element.
Do not change the parameter settings excessively.
The failure could result in instable or unexpected operation.

PR-007
Caution (corrective actions)
If any alarm has occurred, eliminate its causes of the alarm and secure the
safety before restarting the operation.
The failure could result in damages or bursts.
When it is assumed that a hazardous condition may take place at the
occurrence due to a product fault, use an external holding brake mechanism.
If any alarm has occurs, the motor goes into free-run state.
If any product fault has occurred, shut off the power immediately and do not
turn on the power.
The failure could result in damages or bursts.
Caution (maintenance, inspection)
Only persons who are trained and qualied to work or on electrical
equipment are permitted to maintain or inspect the product.
Incorrect handling or operation could cause electric shocks or damages.
Do not perform a dielectric voltage-withstand test.
The failure could result in destruction of circuit element.
About processing of waste
This product should be treated as an industrial waste when it is disposed.
MUSCLE CORPORATION is not responsible for any damages
resulting from modications or repairs made to the product.

IN-001
INDEX
Chapter 1
Functions and Structure���������������������������������������������������001
1.1. Overview��������������������������������������������������������������������001
1.2. Block Diagram���������������������������������������������������������������002
1.3. Product Code Scheme�������������������������������������������������������002
1.4. Parts Description������������������������������������������������������������003
1.5. Motor's Rotating Direction����������������������������������������������������003
1.6. Status LED������������������������������������������������������������������004
1.7. Control Type�����������������������������������������������������������������005
1.7.1. Pulse Type (P Type)�����������������������������������������������������005
1.7.2. Computer Type (C Type)�������������������������������������������������005
1.7.3. Interpolation Type (R Type)����������������������������������������������005
Chapter 2
Installation����������������������������������������������������������������006
2.1. Operating Condition����������������������������������������������������������006
2.2. Mounting to Machinery�������������������������������������������������������006
2.2.1. General Notes�����������������������������������������������������������006
2.2.2. Coupling / Centering����������������������������������������������������008
2.2.3. Allowable Shaft Load����������������������������������������������������008
2.2.4. Notes for Shaft Load����������������������������������������������������009
2.3. Notes for Cabling������������������������������������������������������������ 010
Chapter 3
Wiring and Connections���������������������������������������������������� 011
3.1. Typical Connection Example�������������������������������������������������� 011
3.2. Connector Pin Layout and Functions������������������������������������������ 012
3.3. Connecting to Power Supply�������������������������������������������������� 014
3.4. Connecting to Equipments���������������������������������������������������� 015
3.4.1. Connection for Host Communication�������������������������������������� 015
3.4.2. Connection for Pulse Input����������������������������������������������� 016

IN-002
3.4.3. Digital Input/Output����������������������������������������������������� 017
3.4.4. Connection for Analog Input/Output�������������������������������������� 017
3.4.5. +5V Output������������������������������������������������������������� 017
3.5. I/O Circuit ������������������������������������������������������������������ 018
3.6. Connection Example��������������������������������������������������������� 019
Chapter 4
Communication Functions�������������������������������������������������020
4.1. Communication Software Overview�������������������������������������������020
4.2.ConrmingCommunication��������������������������������������������������� 020
4.3. Communication Method������������������������������������������������������022
4.4. Communication Time���������������������������������������������������������023
4.4.1. Transmission Time�������������������������������������������������������023
4.4.2. Response Time���������������������������������������������������������� 024
Chapter 5
Operating the Motor�������������������������������������������������������025
5.1. Basic Motion����������������������������������������������������������������� 025
5.2. Multiple Axes Control Motion�������������������������������������������������026
Chapter 6
Input/Output Functions���������������������������������������������������027
6.1. Input / Output Functions����������������������������������������������������� 027
6.1.1. Digital Input������������������������������������������������������������� 027
6.1.2. Digital Output�����������������������������������������������������������028
6.1.3. Analog Input������������������������������������������������������������� 029
6.1.4. Analog Output�����������������������������������������������������������030
6.2. I/O Signal according to Control Type������������������������������������������030
6.2.1. Pulse Input��������������������������������������������������������������030
Chapter 7
Various Other Functions��������������������������������������������������� 031
7.1. Origin Search���������������������������������������������������������������� 031
7.2. Push Motion����������������������������������������������������������������� 031
7.3. Manual Jog and Feed���������������������������������������������������������032
7.4. Torque Control���������������������������������������������������������������032
Table of contents
Popular Controllers manuals by other brands

Digiplex
Digiplex DGP-848 Programming guide

YASKAWA
YASKAWA SGM series user manual

Sinope
Sinope Calypso RM3500ZB installation guide

Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS
LSIS sv-ip5a user manual

Rockwell Automation
Rockwell Automation 1769-L31 installation instructions











