Moxa Technologies EDS-505A Series Manual

MOXA EtherDevice™ Switch

EDS-505A/508A Hardware Installation Guide

Fourth Edition, February 2008

Moxa Inc.

Tel: +886-2-8919-1230

Fax: +886-2-8919-1231

www.moxa.com

Moxa Technical support.

Worldwide: support@moxa.com

The Americas: support@usa.moxa.com

P/N: 1802005000011

—1 —

Package Checklist

The MOXA EDS-505A/508A is shipped with the following items. If any of

these items is missing or damaged, please contact your customer service

representative for assistance.

y1 MOXA EtherDevice Switch (EDS-505A or EDS-508A)

yHardware Installation Guide

yCD-ROM with User’s Manual and Windows Utility

yWarranty Statement

yRJ45 to DB9 Console port cable

yProtective caps for unused ports

yPanel Mounting Kit (optional—must be ordered separately)

Features

¾Advanced Industrial Networking Capability

yPlug-n-Play, Redundant Ethernet Ring and RSTP/STP (IEEE802.1W/D)

yIGMP Snooping and GMRP for filtering multicast traffic from

Industrial Ethernet

ySupports port-based VLAN, IEEE802.1Q VLAN and GVRP protocol to

ease network planning

ySupports QoS-IEEE802.1p/1Q and TOS/DiffServ to increase

determinism

ySupports 802.3ad, LACP for optimum bandwidth utilization

yPort Trunking for optimum bandwidth utilization

yRMON for efficient network monitoring and proactive capability

ySNMP V1/V2c/V3 for different levels of network management security

ySupports IEEE802.1X and https/SSL to enhance network security

¾Designed for IndustrialApplications

yBandwidth management to prevent unpredictable network operation

yPort mirroring for online debugging

yLock port for authorized MAC address access

yDigital inputs to integrate sensors and alarms with IP networks

yAutomatic warning by exception through email, relay output

yAutomatic recovery of IP addresses from connected devices

yLine-swap fast recovery (patent pending)

yRedundant, dual DC power inputs

y-40 to 75°C operating temperature range (for-T models)

yIP30, rugged high-strength case

yDIN-Rail or panel mounting ability

yLong-haul transmission distance of 40 km or 80 km.

—2 —

Panel Layout of EDS-505A/508A

(Standard)

EDS-505A

Front Panel View EDS-508A

Front Panel View

V1, V2 INPUTS: 12-45 VDC

RS-232 CONSOLE

------

OFF

MASTER

COUPLER

TURBO

RING

PWR2

RELAY2

RELAY1

DI1

V2-

V2+

V1-

V1+

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. Master LED

10. Coupler LED

11. Turbo Ring logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100BaseT(X) ports

16. Screw hole for wall mounting kit

17. DIN-Rail kit

—3 —

Panel Layout of EDS-505A/508A

(SC-type)

EDS-505A-MM-SC

Front Panel View EDS-508A-MM-SC

Front Panel View

V1, V2 INPUTS: 12-45 VDC

RS-232 CONSOLE

------

OFF

MASTER

COUPLER

TURBO

RING

PWR2

RELAY2

RELAY1

DI1

V2-

V2+

V1-

V1+

Top Panel View

Rear Panel View

NOTE: The appearance of

EDS-505A-SS-SC is identical to that

of EDS-505A-MM-SC.

The appearance of EDS-508A-SS-SC

is identical to that of

EDS-508A-MM-SC.

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. Master LED

10. Coupler LED

11. Turbo Ring logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100BaseT(X) ports

16. 100BaseFX ports

17. FX port’s 100 Mbps LEDs

18. Screw hole for wall mounting kit

19. DIN-Rail kit

—4 —

Panel Layout of EDS-505A/508A

(ST-type)

EDS-505A-MM-ST

Front Panel View EDS-508A-MM-ST

Front Panel View

V1, V2 INPUTS: 12-45 VDC

RS-232 CONSOLE

------

OFF

MASTER

COUPLER

TURBO

RING

PWR2

RELAY2

RELAY1

DI1

V2-

V2+

V1-

V1+

Top Panel View

Rear Panel View

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2 and relay output

3. Heat dissipation orifices

4. Console port

5. DIP switches

6. Power input PWR1 LED

7. Power input PWR2 LED

8. Fault LED

9. Master LED

10. Coupler LED

11. Turbo Ring logo

12. TP port’s 100 Mbps LED

13. TP port’s 10 Mbps LED

14. Model Name

15. 10/100BaseT(X) ports

16. 100BaseFX ports

17. FX port’s 100 Mbps LEDs

18. Screw hole for wall mounting kit

19. DIN-Rail kit

—5 —

Mounting Dimensions (unit = mm)

Rear View

Side View

Front View

DlN-Rail Kit

DlN-Rail

105.00

9.00

35.00

135.00

24.324.56 46.77 39.37

135.00

Wall Mounting Kit

7.75 30.50 7.75

3.5

66.80

57.05

13.9 18.2 13.9

30.00 15.0

51.3 13.9

80.2

DlN-Rail Kit

7.5 55 7.5

27.20

48.30

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the back

panel of the EDS-505A/508A when you take it out of the box. If you need to

reattach the DIN-Rail attachment plate, make sure the stiff metal spring is

situated towards the top, as shown in the following figure.

STEP 1:

Insert the top of the DIN-Rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN-Rail attachment unit will

snap into place as shown.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove EDS-505A/508A from the DIN-Rail, simply reverse Steps 1 and 2.

—6 —

Wall Mounting (optional)

For some applications, you will find it convenient to mount the

EDS-505A/508A on the wall, as shown in the following figures.

STEP 1: Remove the

aluminum DIN-Rail

attachment plate from the

EDS-505A/508A’s rear

panel, and then attach the

wall mount plates with M3

screws, as shown in the

figures at the right.

⇒

STEP 2:

Mounting the EDS-505A/508A on the wall requires 4 screws.

Use the EDS, with wall mount plates attached, as a guide to

mark the correct locations of the 4 screws. The heads of the

screws should be less than 6.0 mm in diameter, and the shafts

should be less than 3.5 mm in diameter, as shown in the

figure at the right.

6.0 mm

3.5 mm

NOTE Before tightening the screws into the wall, make sure the screw head

and shank size are suitable by inserting the screw into one of the

keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in completely—leave about 2 mm to allow room for

sliding the wall mount panel between the wall and the screws.

STEP 3: Once the screws are fixed in

the wall, insert the four screw heads

through the large parts of the

keyhole-shaped apertures, and then

slide the EDS-505A/508A

downwards, as indicated. Tighten the

four screws for added stability.

ATEX Information

1. Certificate number 08 ATEX 0712961X

2. Ambient range (-40°C ≤Tamb ≤75°C)

3. Certification string (Ex nC nL IIC T4)

4. Standards covered ( EN60079-0:2006, EN60079-15:2005)

5. The conditions of safe usage:

yThese products must be mounted in an IP54 enclosure.

yInstall in an area of pollution degree 2 or less.

yUse a conductor wire of size 0.2 mm² or greater.

yPROVISIONS SHALL BE MADE, EITHER IN APPARATUS OR

EXTERNAL TO THE APPARATUS, TO PREVENT THE RATED

VOLTAGE BEING EXCEEDED BY THE TRANSIENTS

DISTURBANCES OF MORE THAN 40 %

—7 —

Wiring Requirements

WARNING

The power for this product is intended to be supplied by a Listed

Power Unit, with output marked LPS, and rated to deliver 12 to

45 VDC at a maximum of 600 mA.

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your MOXA EtherDevice Switch. Calculate the maximum

possible current in each power wire and common wire. Observe

all electrical codes dictating the maximum current allowable for

each wire size. If the current goes above the maximum ratings,

the wiring could overheat, causing serious damage to your

equipment.

Please read and follow these important guidelines:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

yNOTE: Do not run signal or communications wiring, and power wiring

through the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

yUse the type of signal transmitted through a wire to determine which wires

should be kept separate. The rule of thumb is that wiring that shares similar

electrical characteristics can be bundled together.

yKeep input wiring and output wiring separate.

yIt is strongly advised that you label wiring to all devices in the system,

when necessary.

Grounding the EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface, such as a metal panel.

Wiring the Relay Contact

The EDS-505A/508A has two sets of relay output—relay 1 and relay 2. Each

relay contact consists of two contacts of the terminal block on the

EDS-505A/508A’s top panel. Refer to the next section for detailed instructions

on how to connect the wires to the terminal block connector, and how to attach

the terminal block connector to the terminal block receptor. The meaning of the

two contacts used to connect the relay contacts is illustrated below.

—8 —

Relay1 Relay2

The fault circuit will open if::

1. A relay warning event is

triggered, OR

2. The EDS-505A/508A is the

Master of this Turbo Ring,

and the Turbo Ring is broken,

3. Start-up failure.

If none of these three conditions

is met, the fault circuit will

remain closed.

Wiring the Redundant Power Inputs

The EDS-505A/508A unit has two sets of power inputs—power input 1 and

power input 2.The top two contacts and the bottom two contacts of the 6-pin

terminal block connector on the top panel are used for the EDS’s two digital

inputs. Top and front views of one of the terminal block connectors are shown

below.

PWR1 PWR2

V1- V1+

PWR1

V2- V2+

PWR2

V1- V1+ V2- V2+

Take the following steps to wire

the redundant power inputs:

STEP 1: Insert the

negative/positive DC wires into

the V-/V+ terminals.

STEP 2: To keep the DC wires

from pulling loose, use a small

flat-blade screwdriver to tighten

the wire-clamp screws on the

front of the terminal block

connector.

STEP 3: Insert the plastic

terminal block connector prongs

into the terminal block receptor,

which is located on the EDS’s top

panel.

ATTENTION

Before connecting the EDS to the DC power inputs, make sure

the DC power source voltage is stable.

Wiring the Digital Inputs

The EDS-505A/508A unit has two sets of digital inputs, DI 1 and DI 2. Each

DI consists of two contacts of the 6-pin terminal block connector on the EDS’s

top panel. The remaining contacts are used for the EDS’s two DC inputs. Top

and front views of one of the terminal block connectors are shown below.

—9 —

D2I

D1I

I1I2

D2ID1I

Take the following steps to wire

the digital inputs:

STEP 1: Insert the negative

(ground)/positive DI wires into

the ┴/I1 terminals.

STEP 2: To keep the DI wires

from pulling loose, use a small

flat-blade screwdriver to tighten

the wire-clamp screws on the

front of the terminal block

connector.

STEP 3: Insert the plastic

terminal block connector prongs

into the terminal block receptor,

which is located on the

EDS-505A/508A’s top panel.

Communication Connections

EDS-508A models have 8 or 6 10/100BaseT(X) Ethernet ports, and 0 (zero) or

2 100BaseFX (SC/ST-type connector) fiber ports. EDS-505A models have 5 or

3 10/100BaseT(X) Ethernet ports, and 0 (zero) or 2 100 BaseFX (SC/ST-type

connector) fiber ports

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on EDS’s front panel are used to connect to

Ethernet-enabled devices.

Next, we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also show cable wiring diagrams for

straight-through and cross-over Ethernet cables.

MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45

Pin Signal Pin Signal

1 Tx+ 1 Rx+

2 Tx- 2 Rx-

3 Rx+ 3 Tx+

6 Rx- 6 Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

Straight-Through Cable

RJ45 Plug Pin 1

Switch Port

RJ45

Connector RJ45

Connecto

Tx+

Tx-

Rx+

Rx-

NIC Port

Cable Wiring

3 3

6 6

1 1

2 2

Rx+

Rx-

Tx+

Tx-

Other manuals for EDS-505A Series

This manual suits for next models

Table of contents

Other Moxa Technologies Switch manuals

Moxa Technologies

Moxa Technologies PT-G7828 User manual

Moxa Technologies

Moxa Technologies TN-G4516-8GPoE-4XGPoE-WV-T User manual

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-4012 Series User manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4POE-1GSFP-T User manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A-T Manual

Moxa Technologies

Moxa Technologies ToughNet TN-5510A-2GLSX-ODC Manual

Moxa Technologies

Moxa Technologies EDS-G308 Series User manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-G500E Series User manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-30 Manual

Moxa Technologies

Moxa Technologies PT-7528 Manual

Moxa Technologies

Moxa Technologies UPORT 1200 series User manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series User manual

Moxa Technologies

Moxa Technologies EDS-4014 Series User manual

Moxa Technologies

Moxa Technologies MDS-G4000-L3-4XGS Series User manual

Moxa Technologies

Moxa Technologies EDS-2008-EL Series User manual

Moxa Technologies

Moxa Technologies ThinkCore DA-660-8-CE User manual

Moxa Technologies

Moxa Technologies PT-7828 Series User manual

Moxa Technologies

Moxa Technologies IKS-G6524 Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-828 Series User manual

Moxa Technologies

Moxa Technologies NPort S8000 Series User manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-G508E-T Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-516A-T Manual

Moxa Technologies

Moxa Technologies EDS-516A Series User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual