Mountup MU6002 User manual
Dual Monitor Desk Mount
Instruction Manual
If you have any questions , please contact us.
MU6002
V2.0
75x75
100x100
(2~8kg)x2
(4.4~17.6lbs)x2
32"
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, please contact us.
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
WARNING!
PACKAGE CONTENTS
E (x1)
Bracket
F (x1)
Clamp
I (x1)
Grommet Base
L (x2)
Bolt
K (x1)
Carriage Bolt
N (x1)
3mm Allen Key
O (x1)
4mm Allen Key
P (x1)
6mm Allen Key
G(x5)
M6x10
H(x4)
Pad
D (x2)
VESA Plate
01
M (x1)
Support Plate
DO NOT EXCEED WEIGHT CAPACITY.
(17.6lbs)x2
(8kg)x2
J (x1)
Wingnut
M-C (x8)
D6 Washer
M-A (x8)
M4x12
M-B (x8)
M6x12 M-D (x8)
spacer
A (x2)
Upper Arm
B (x2)
Lower Arm
C (x1)
Base
ASSEMBLY STEPS
02
OPTION A: Clamp Installation
Mount Bracket (E) to Base Bottom (C) with Bolts (G). Bolts could be tightened by the 4mm Allen Key (O).
Similarly, attach Clamp (F) to Bracket (E) with Bolts (G) and 4mm Allen Key (O).
Adjust the Clamp width to t with desk. Secure stand to desktop by tightening Clamp (F) or by Allen key (P).
G
OO
G
10-60mm
10-90mm
F
F
E
C
E
E
E
G
O
OR
STEP 2: Clamp Installation or Grommet Base Installation
STEP 1: Apply Pads to the Base Bottom
H
Apply pads (H) to the base
bottom to avoid desk scratches.
C
P
OR
STEP 2: (Continued)
03
OPTION B: Grommet Base Installation
For grommet hole mounting, place Carriage Bolt (K) through the center of Grommet Base (I).
Mount Grommet Base to Base Bottom (C) with Bolts (G) and tighten by 4mm allen key (O).
Run Carriage Bolt (K) through Grommet Hole on desktop. Attach Support Plate (M) and Wingnut (J).
Last step, tighten Wingnut (J).
O
C
I
G
K
M
J
10-90mm
04
N
A
F
B
C
N
Install the lower arm (B) and the upper arm (A) to the base (C). Secure the arm by tightening the inside screw
using Allen key (N).
STEP 3: Arm Installation
Note: Please note that the side with
the label“ ” is installed on the
base(C) when installing the lower
arm(B) to the base (C).
DO NOT tighten the
screw excessively or
it might be stripped.
DO NOT tighten the
screw excessively or
it might be stripped.
05
STEP 4: Attach Monitor
D
D
M-A
M-B
M-C
P
M-A
M-B
M-C
M-D
P
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to back of monitor and
secure with screws(M-A)or(M-B) with washers(M-C)
using 6 mm Allen Key (P). Do not tighten the screws
excessively or your monitor might be damaged.
CAUTION:To select the correct screws(M-A or M-B)
for your monitor, you can try to screw it on your
monitor by hand. The one can screw inside is the
correct screw for your monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to back of monitor and secure
with screws (M-A) or (M-B) with washers (M-C)and
spacers(M-D)using 6 mm Allen Key (P). Do not tighten
the screws excessively or your monitor might be damaged.
06
Slide the monitor onto the head of swivel arm, install the security bolt (L). Make sure the security
bolt is installed before you rotate the monitor.
STEP 5: Hang Monitor
Tilts down
Note:
1. Loosen the tilting bolt.
2. Adjust monitor to your
desired tilting angle.
3. Retighten the tilting bolt to
P
spring arm falls down greatly.
L
Important Notice:
The gas spring is pre-set to minimum tension. Once the monitor is hanged on, hold the
monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the
monitor in a slow & gentle way while observing whether the arms will fall down wildly.
Guideline to adjust monitor tilting angle.
07
STEP 6: Adjust Tension
P
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Falls down
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor canstay at the desired
height by itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor canstay at the desired height by itself.
Rises up
CAUTION
Monitor Weight 2kg 3kg 4kg 5kg 6kg 7kg 8kg
Circles (AT LEAST)
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in upper arm (A) using 6 mm allen key (P).
1 4 8 11 14 17
min
As for how many circles the screw should be turned, refer to below diagram.
Note2:
If the monitor falls down and fails to stay at the desired
height by itself:
If the monitor rises up and fails to stay at the desired
height by itself:
STEP 5: (Continued)
08
STEP 7: Cable Management
Run cables from monitor through bottom of gas spring arm. Reattach plastic covers as shown in diagram.
Remove bottom plastic covers from gas spring arm as shown in diagram.
Adjust as Desired
09
DESK DESK
Pay attention while clamp install !
180°
360°
+90°
-45°
360°
270°
Adjust monitor position and rotation.
Table of contents
Other Mountup Rack & Stand manuals
Mountup
Mountup MU0024 User manual
Mountup
Mountup MU5001 User manual
Mountup
Mountup MU4002 User manual
Mountup
Mountup MU6001 User manual
Mountup
Mountup MU4003 User manual
Mountup
Mountup MUA6007B User manual
Mountup
Mountup MU9101B User manual
Mountup
Mountup MU0027 User manual
Mountup
Mountup MU0005 User manual
Mountup
Mountup MU0023 User manual
Mountup
Mountup MU0004 User manual
Mountup
Mountup MU0006 User manual
Mountup
Mountup MU0002 User manual
Mountup
Mountup MU0014 User manual
Mountup
Mountup MU5004 User manual
Mountup
Mountup MU0021 User manual
Mountup
Mountup MU0004 User manual
Mountup
Mountup MU0045 User manual
Mountup
Mountup MU2001 User manual
Mountup
Mountup MUA6008B User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
