Mountup MU6003 User manual

Height Adjustable Single Monitor Desk Mount

Instruction Manual

75x75

100x100 (2~9kg)

(4.4~19.8lbs)

32"

If you have any questions, please feel free to contact our customer service via Amazon. AHP-21-US1.0

NOTE: Not all hardware included will be used.

DO NOT EXCEED WEIGHT CAPACITY.

WARNING!

PACKAGE CONTENTS

(4.4~19.8lbs)

(2~9kg)

A (x1)

Arm

B (x1)

Clamp

All are included in B

Bracket

Clip Plate

Bolt Y

C (x1)

Decorative Cover

F (x1)

Bolt

I(x1)

5mm Allen Key

J(x1)

6mm Allen Key

E(x1)

Base

E1(x3)

Pad

D (x1)

VESA Plate

M-C (x4 )

D5 Washer

M-D (x8 )

Spacer H5mm

M-B (x4 )

M4x30mm

M-A (x4 )

M4x12mm

Bolts

B4(x2)

A1 (x1)

Harness Cover

G (x1)

Wire Clip

H(x1)

Fixator

If you have any confusions or are not quite sure about the installation, please do not hesitate to ask

for our help.

Before assembly, please check and make sure all necessary accessories are included and

undamaged. Improper installation, such as use the product for monitors over its load capacity or for

any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for

any damage or injury caused by improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF

REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

ASSEMBLY STEPS

STEP 1: Apply Pads to the Base Bottom

OPTIONA

STEP 2: Clamp Installation Or Grommet Base Installation

Fix the Decorative Cover (C) to the Base (E) and fix thebracket on the table by tightening the

Clamp (B).Use a 5mm Allen Wrench (I).

Paste the Pad (E1) onto the Base (E)

Loosen Bolts (B4) by using 5mm Allen Key (I),Then align the screw hole on the Base (E), and

then lock the Screw (B4) with a 5mm Allen Wrench (I).

OPTION A: Clamp Installation

Min10mm~Max50mm

Don't over tightened

OPTION B: Grommet Base Installation

STEP 2: (Continued)

Use Bolt Y (B3) through the screw hole on Bracket (B1) to fix the Base (E) and the table board

together.

Use 5mm Allen Key(I) to detach Clip Plate(B2)and bolt Y(B3) from Clamp(B).

EMin10mm~Max50mm

Install Arm (A),Fixator(H) ,Wire Clip (G) on the base in sequence as shown below.

Make sure to tighten the Fixator(H) to desired place with 5mm Allen Key.

Adjust the tightness of the bolt of Arm(A) to make the rotation flexible.

STEP 3 : Arm Installation

NOTE: Hand tighten screws to avoid over tightening.

STEP 4 : Attach Monitor

M-A

M-C

OPTION B: Curved Back Monitor

Attach the VESA Plate (D) to back of monitor and secure

with Screws (M-B) with Washers (M-C)and

Spacer(M-D)using 5 mm Allen Key (I). Avoid excessive

tightening screws damage the monitor.

OPTION A: Flat Back Monitor

Attach the VESA Plate (D) to back of monitor and

secure with Screws(M-A) with Washers(M-C )

using 5 mm Allen Key (I). Avoid excessive

tightening screws damage the monitor.

M-B

M-C

M-D

one or two piece

STEP 5 : Hang Monitor

Refer to below illustrations to

adjust tilting angle of your monitor.

Important Notice:

Once the monitor is hanged on, hold the monitor with both hands and DO NOT let go

suddenly or immediately. Instead, leave the monitor in a slow & gentle way while

observing whether the arms will fall down wildly.

Solution:

1. Loosen the tilting bolt.

2. Hold the bottom of monitor

with one hand and adjust to

determine your desired tilt

angle.

3. Retighten the tilting bolt to

fix the intended angle.

Problem:

If monitor face down

Slide the monitor onto the head of swivel arm.Install the Security Bolt (F).

Make sure the security bolt is tightened before you rotate the monitor.

STEP 6 : Adjust Tension

CAUTION

Note1:

Situation 1: Arm falls down

Solution:

Upper Arm with monitor falls down and fails to stay where

intended.

Turn the inside screw counterclockwise(“+”direction) to increase

gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up

Solution:

Upper Arm with monitor rises up and fails to stay where intended.

Turn the inside screw clockwise(“-”direction) to decrease gas

spring tension until the arm can stay as intended.

Be sure to keep the arm in horizontal position during adjustment.

For intended functioning of the mount, you may need to adjust the tension of Arm (A) in

accordance with your monitor weight by 6 mm Allen Key (J).

(AT LEAST) 2 4 6 8 10 12 15

min

For how many circles the screw should be turned, please refer to the table below.

Note2:

STEP 7 : Cable Management

Insert

Tighten

Insert

Press

1.Remove the cable cover using a 5mm Allen Key (I)

2.Fix the wire in the harness wire cover

3.Install and fix the harness cover on the Arm (A) using a 5mm Allen Key (I)

Remove bottom plastic covers from gas spring Arm (A) .Run cables from monitor through bottom

of gas spring Arm (A). Then cover the Wire Cap (A1) onto the upper arm of the Arm (A).

Reattach plastic covers as shown in diagram.

Adjust as Desired

DESK DESK

Please do not move stand

outside desk for safety!

±135°

±180°

±90°

±180°

Note: To ensure stability, the tightness of the rotating axis has been

preset, so it would be kind of difficult to rotate the VESA plate.

Suggestion: Please attach the monitor first, then hold the two sides of

it with both hands, and rotate vigorously.

If that doesn't work out, please do not hesitate to ask for our help.

Adjust monitor position and rotation.

Swivel

Tilt

Swivel

Rotation

+90°

-90°

Tilt

Rotation

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 