Mosaic MH107 User manual

User Manual of MH107

1. Product Features

Name: Wireless Door & Window Alarm

Working voltage: 3V

Standby current: 100uA

Working current: 50mA

Power: 0.15w

1. Type: magnetic induction

2. Sounds an alarm when somebody opens the door or window illegally.

3. Can be free controlled by the wireless remote control.

4. A password of 3 digits can be set, and it won't be lost even if power off.

5. Zone control function. Multiple devices can be controlled by the remote

control at different zones

6. Siren on/off setting

7. Setting of reminder sound when door not closed

8. Setting of reminder sound when door not locked

9. "DING DONG" sound when linked with MH101 Door Phone for use.

10. Triggers MH102 Video Camera to take videos when linked with it for use.

11. RF on/off setting

12. Lock the keypad automatically when entering wrong password 5 times.

13. Sounds an alarm after 4 seconds when triggered.

14. LED indicator when battery low

15. Still sounds an alarm even in the environment of strong magnetism.

2. Installation and Use

1.Take out the insulating piece, and you will hear one "bi", which means correct

insert of the battery.

2.Tear off the protection paper of 3M adhesive tape on the back of MH107, and

stick the magnet part parallel to the alarm, ensuring the gap to be less than

1cm.

3. Function setting

Password setting

Password setting n

* Default password is "1 2 3" d when door not closed

1) . ARM

Press "3" on the keypad and we will hear one beep. 20 seconds later it

is ARMED

2) .DISARM

Enter the correct password and press "3".After one beep it is DISARMED.

(default password is "1 2 3" if it's not revised)

3) .Revise password

In the status of "DISARMED", enter the current password "1 2 3" and press "3", red

light stays on for 3 seconds. Enter the new password "xxx" and enter "1 2 3" again

and press "3", the red light flashes 3 times. New password is successfully set.

("xxx" stands for new password; default password is "1 2 3" if it's not revised)

RF on/off

1) .ON

Enter the password "xxx" and enter "2111" to turn the RF function on. Red light

flashes 3 times. In this case, MH107 can work with other wireless units.

2) .OFF

Enter the password "xxx" and enter "2112" to turn the RF function off. Red light

flashes 3 times. In this case, MH107 can't work with other wireless units and it

will work individually

Siren on/off

1 ).ON

Enter the password "xxx" and enter "2121" to turn the siren on. Red light flashes

3 times. When MH107 is triggered, the siren will sound.

2) .OFF

Enter the password "xxx" and enter "2122" to turn the siren off. Red light

flashes 3 times. When MH107 is triggered, the siren will not sound

Reminder sound when door not closed

1) .ON

Enter the password "xxx" and enter "2211" to turn the sound on. Red light

flashes 3 times.

2) .OFF

Enter the password "xxx" and enter "2212" to turn the sound off. Red light

flashes 3 times.

Reminder sound when door not locked

1) .ON

Enter the password "xxx" and enter "2221" to turn the sound on. Red light

flashes 3 times.

2) .OFF

Enter the password "xxx" and enter "2222" to turn the sound off. Red light

flashes 3 times

4. Reset to default factory

Open the battery cover and take out the battery. After 3 seconds, press and

hold the learn code key, and insert the battery. When you hear three beeps,

it has been reset to default factory. Default password is "1 2 3"

5. Pairing two MH107, Divide into different zones

With the help of the remote control, you can pair two units to be divided into

different zones and managed separately by the same remote.

a. Zone “1”： Open the battery cover of unit "1", press the code button

continuously, at same time press the "1 " button (represent zone 1) of the

remote control for 3 seconds, the red light of the remote control will flash

and beeps twice. Zone "1" is set successfully. The button “1” can

arm/disarm alarm unit "1" installed at Zone 1.

b. Zone “2”：Open the battery cover of unit "2", press the code button

continuously, at same time press the "2 " button (represent zone 2) of the

remote control for 3 seconds, the red light of the remote control will flash and

beeps twice. Zone "2" is set successfully. The button “2 ” can arm/disarm alarm

unit "2" installed at Zone 2.

6. Remark

1).Every step of button operation must be completed within 5 seconds.

2 ).When you enter the password wrongly for 5 times, MH107 sounds a

2-second beep and 10 beeps, and the keypad will be locked for 5 minutes.

After that time, you can use the remote control to unlock the keypad and

re-enter the password.

FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION:

Changes or Modifications not expressly approved by the party responsible

could void the user’s authority to operate this device.

NOTE: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which

the receiver is

connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Examples of RF Exposure statement:

This equipment complies with the FCC RF radiation exposure limits set forth

for an uncontrolled

environment.This equipment should be installed and operated with a minimum

distance of 20 centimeters between the radiator and your body.

FCC ID: ZAX5E-MH107

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause to harmful interference,

and (2) This device must accept any interference received, including

interference that may cause undesired operation.

After-sale service

Please don't hesitate to call the service hotline, contact the online customer

service or visit Mosaic website.

Hotline: 0769-8544 9889

Email: sales01@mosaichk.net

Website: www.mosaichk.net

Table of contents

Other Mosaic Security System manuals

Mosaic

Mosaic MH803 User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual