Molex ServiceGrade 64016-0036 User guide

Hand Crimp Tool for Avikrimp™ /Insulkrimp ™ Terminals and Slices

Doc No: ATS-64 16 36 Release Date: 6-25-12 UNCONTROLLED COPY Page 1 of 4

Revision: A Revision Date: 6-25-12

ServiceGrade





Hand Crimp Tool

Application Tooling

Specification S eet Order No. 64016-0036

FEATURES





 A full cycle ratcheting hand tool ensures complete crimps





 Ergonomic soft grip handles for comfortable crimping





 For crimps conforming to industry standards such as UL, USCAR21, and WHMA-IPCA62 Class 2,

please use the 64 1- 1 Premium Grade™ hand tool for the Molex terminal

SCOPE

Products: Avikrimp™ /Insulkrimp ™ Terminals and Splices 1 - 22 AWG, (Rings, Spades, Hooks, Block Spades

and Flanged Spades). Also terminates ends of step down butt splice 1 -12 to 14 - 16 AWG and 14 - 16 to 18 -

22 AWG.

Crimping Information:

Crimp the terminal and appropriate gauge wire in the specified profile.

Description Wire Size Pull Force Min. ▼

Tool Crimp Profile

Markings

AWG

Lb.

Red

lue

Yellow

Terminals

(Rings, spades, hooks,

block spades, or

flanged spades)

356.

8 .

3.3

311.5

7 .

222.6

5 .

1.3

133.5

3 .

89.

2 .

57.9

13.

.35

35.6

Splices

(Butt splices or

parallel splices)

178

4 .

3.3

155.7

35.

111.2

25.

1.3

66.8

15.

44.5

1 .

44.5

1 .

.35

35.6

▼

Pull force test samples should not have the wire insulation crimped.

Note:

An occasional, destructive, pull force test with the terminal and wire crimped should be performed to check hand

tool crimp. The pull force value must exceed the terminal’s minimum pull force specifications listed above. If values

do not exceed the minimum pull force when all instructions are followed then a new tool is required.

Hand Crimp Tool for Avikrimp™ /Insulkrimp ™ Terminals and Slices

Doc No: ATS-64 16 36 Release Date: 6-25-12 UNCONTROLLED COPY Page 2 of 4

Revision: A Revision Date: 6-25-12

Figure 1

TERMINAL

WIRE

HAND TOOL

OPEN

MWID OR MAX

INSULATION DIAMETER

STRIP

LENGTH

STUD SIZE

(REF)

BARREL

BRUSH

INSULATION

FERRULE

TERMINAL

Figure 2

WIRE

CONDUCTOR P

UNCH

INSULATION PUNCH

DEFINITION OF TERMS

The illustrations in this document are a general representation. Some of

the terminals may look different and be held in a different area of the

terminal.

OPERATION

CAUTION: Install only Molex terminals listed above with this tool.

Do not crimp hardened objects as damage can occur to the tool.

WARNING: Make sure that the wire is DISCONNECTED from any

power supply

Make sure work area is clean and dry and wear approved eye

protection.

Open the hand tool by squeezing the handles together; at the end of the closing stroke the anti-backup ratchet will

release. Release the handles and the hand tool will open.

Crimping Terminals

1. Select the desired terminal. See the Molex website (http://www.molex.com).

2. Holding the terminal at the contact end, place the terminal in the appropriate nest. See Figure 1.

3. Slowly close the handles of the tool until the terminal is held in place. If the handles are closed too far the

terminal will begin to crimp.

4. Place a pre-stripped wire into the terminal. See terminal product specification on the Molex website. Push the

wire into the terminal barrel until it stops. See Figure 2.

5. While holding the wire in place, slowly close the handles of the tool. If a jam occurs, stop closing the tool and

release the anti-backup ratchet located on the top of the tool. Pushing it forward will release the jaws. See

Figure 5.

6. Continue to close the tool handles until the anti-backup ratchet releases. Allow the handles to open.

7. Remove the crimped terminal from the tool.

8. Inspect the crimp for loose wire strands, missing crimp, or other damage. Any minor terminal bending may be

straightened by hand.

Hand Crimp Tool for Avikrimp™ /Insulkrimp ™ Terminals and Slices

Doc No: ATS-64 16 36 Release Date: 6-25-12 UNCONTROLLED COPY Page 3 of 4

Revision: A Revision Date: 6-25-12

BUTT SPLICE

TERMINAL

Figure 3

WIRE

WIRE TAB

Crimping Butt Splices

1. Position the splice into the nest.

2. Partially close the tool to hold the splice in place.

3. Insert the properly stripped wire into the splice. The wires end

should butt against the tab in the terminal. See Figure 3.

4. Continue to close the tool handles until the anti-backup ratchet

releases. Allow the handles to open.

5. Remove the crimped splice. Inspect for proper crimp location.

6. Rotate the butt splice terminal 18 °, so that the opposite end of

splice is in the nest.

7. Repeat steps 1 thru 4.

Maintenance

It is recommended that each operator of the tool be made aware of,

and responsible for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean

brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine

oil. Do not oil excessively. Light oil (such as SAE3 W oil) applied at the oil points, shown in Figure 4, every

5, crimps or 3 months, is recommended.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

If the tool ever becomes jammed in a partially closed position, DO NOT force

the handles open or closed. The tool will open by lifting the ratchet release

lever. See Figure 5.

Tool Handle Preload

Tool handle preload should NOT require adjustment upon receipt of tool.

This hand tool is set from the factory to a preload that will fully close the tool jaws without excessive force from the

operator. Over the life of the tool the tool linkage can wear and handle preload force may decrease and preload can

be adjusted. It is the operator’s responsibility to periodically perform a tensile pull test on the crimped wire. If the

pull test value falls below the specification, the preload should be adjusted. If after adjustment, the crimp does not

meet the pull test value, then the tool should be replaced.

Fig

ure

RATCHET RELEASE

LEVER

Figure 4

Hand Crimp Tool for Avikrimp™ /Insulkrimp ™ Terminals and Slices

Doc No: ATS-64 16 36 Release Date: 6-25-12 UNCONTROLLED COPY Page 4 of 4

Revision: A Revision Date: 6-25-12

Warranty

This tool is for electrical terminal crimping purposes only. All tools are warranted to be free of manufacturing defects

for a period of 3 days. Should such a defect occur, the tool will be repaired or exchanged free of charge. This

exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any

clamping, fixturing, or use of handle extensions voids this warranty.

ServiceGrade™ crimp hand tools are low cost tools used in field repair for a limited number of terminations. If a

high quality tool is required or a higher volume of terminations required, please purchase the corresponding

PremiumGrade™ crimp hand tool. A ServiceGrade™ crimp tool may or may not have a terminal locator and in

some case may need the locator removed to operate properly.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock. NEVER perform crimps on active

electrical circuits.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Certification

Molex does not certify or re-certify ServiceGrade™ hand tools but rather supplies the following guidelines for

customers to maintain their hand tools.

% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped

12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

25mm (1. ”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

% When the hand tool is no longer capable of achieving minimum pull force, it should be replaced.

Visit our Web site at http://www.molex.com

This manual suits for next models

Table of contents

Popular Crimping Tools manuals by other brands

Panduit

Panduit CT-1000 Operation & instruction manual

JST

JST CS 10 instruction manual

Danfoss

Danfoss ET4200 Operator's manual

Tyco Electronics

Tyco Electronics PRO-CRIMPER III instruction sheet

TE Connectivity

TE Connectivity 2063528-1 instruction sheet

Tyco Electronics

Tyco Electronics 69156-1 instruction sheet

CRH

CRH CRL CBLHCT1 instruction manual

Emerson

Emerson Klauke ES 105CFM manual

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Operating instructions manual

Danfoss

Danfoss ET4350 Operator's manual

Milwaukee

Milwaukee M18 Operator's manual

HOGERT

HOGERT HT1P169 user manual

Textron

Textron ESG105L instruction manual

Tyco Electronics

Tyco Electronics 90035-3 instruction sheet

Emerson

Emerson Klauke ES 20RMCCFB manual

Continental Refrigerator

Continental Refrigerator PC150HD quick start guide

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 instruction sheet

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 instruction sheet

molex ServiceGrade 64016-0036 User guide

Popular Crimping Tools manuals by other brands