Molex 207129 Series User manual

Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle

oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 1 of 6

Revision: A Revision ate: 06-06-11

TYPE 4A

INSULATION CRIMP

▲SEE NOTE

BRUSH

STRIP LENGTH

TERMINAL

STRIP

CONDUCTOR

CRIMP HEIGHT

CUT-OFF TAB

SEAM

BELL MOUTH

WIRE

CUT-OFF TAB

Applicatio Tooli g

Specificatio Sheet

Modular Crimp Head

Order No. 63823-8570

Ha d Crimp Tool

Order No. 63823-8500

FEATURES

% A full cycle ratcheting hand tool ensures complete crimps

% Ergonomically designed soft handles

% Precisely designed crimping profiles with simple contact positioning

% Easy handling due to outstanding force ratio

% Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63816-0100,

accompanied by Air Powered Crimp Adapter (Order No. 63816-0700).

% Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V),

accompanied by Battery Powered Crimp Adapter (Order No. 63816-0600).

SCOPE

Products: 2.79mm (.110”) Slip-On Quick isconnect Receptacle, for 16-20 AWG.

Termi al Series No.

Termi al Order No.

Wire Size I sulatio Diameter Strip Le gth

Reel Form O ly

AWG

mm²

mm I . mm I .

35711 35711-0700

35711-0710

16 1.31

1.80-2.30

.070-.091

4.50-5.00

.177-.197

18 0.80

20 0.52

Customer to cut off terminal from reel: 0.20mm (.008”) maximum Cut-off Tab.

See crimp specification for the individual Insulation iameter.

DEFINITION OF TERMS

Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle

oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 2 of 6

Revision: A Revision ate: 06-06-11

WIRE

INSULATION

PUNCH

TERMINAL

WIRE STOP BLADE

Figure 1

▲I sulatio Crimp Note:

ue to the terminal’s insulation grip design and/or

insulation diameter range, this tool uses “overlap” form

geometry in the insulation punch. This produces an

overlap insulation crimp (A620 – compliant). While the

insulation punch profile may appear “lopsided”, this is a

normal condition for this tool. See figure to the right.

(Some tools with multiple crimp pockets may not have

the “overlap” profile on all pockets).

CRIMP SPECIFICATIONS:

After crimping, the crimp profiles should measure the following.

Termi al Series No.

Wire Size Co ductor Crimp Profile

Height Width

AWG

mm²

mm I . mm

I . 16

35711

16 1.31 1.35-1.45

.053-.057

2.00

.079

18 0.80 1.15-1.25

.045-.049

2.00

.079

20 0.52 1.00-1.12

.039-.044

2.00

.079

Termi al

Series No.

Wire Size I sulatio Crimp Pull Force Mi imum

Height (Ref)

Width (Ref)

AWG

mm²

mm I . mm I . N Lb.

35711

16 1.31 2.75 .108 3.10 .122

130.43 29.32

18 0.80 2.70 .106 2.95 .116

83.36 18.74

20 0.52 2.35 .093 2.95 .116

59.82 13.45

■Tool Qualification Notes:

1. Pull Force should be measured with no influence from the insulation crimp.

2. The above specifications are guidelines to an optimum crimp.

OPERATION

Open the tool by squeezing the handles together, at the end of the

closing stroke, the ratchet mechanism will release the handles, and

the hand tool will spring open.

Crimpi g Termi als

1. Lift the wire stop blade up.

2. Insert the terminal fully into the correct profile until the terminal

is fully seated and stops.

3. Bring down the wire stop blade.

4. Slide the pre-stripped wire into the wire stop blade. See Figure

1. Be sure to hold the wire in place until the terminal is fully

crimped. See Figure 2.

5. Close the tool until the ratchet releases, the tool handles will then spring open.

6. Lift the wire stop blade up if it is still in down position.

7. Carefully remove the crimped terminal.

OVERLAP

INSULATION

CRIMP

OVERLAP FORM GEOMETRY

ANVIL

PUNCH

WIRE

Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle

oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 3 of 6

Revision: A Revision ate: 06-06-11

Figure 2

WIRE

TERMINAL

LOCATOR

INSULATION

PUNCH

INSULATION

ANVIL

WIRE STOP

BLADE

CONDUCTOR

ANVIL

CONDUCTOR

PUNCH

Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

Mai te a ce

It is recommended that each operator of the tool be made

aware of, and responsible for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a

clean brush, or soft, lint free cloth.

2. o not use any abrasive materials that could damage the

tool.

3. Make certain all pins; pivot points and bearing surfaces are

protected with a thin coat of high quality machine oil. o

not oil excessively. The tool was engineered for durability

but like any other equipment it needs cleaning and

lubrication for a maximum service life of trouble free

crimping. Light oil (such as 30 weight automotive oil) used

at the oil points, every 5,000 crimps or 3 months, will

significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping

area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics

of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.

Warra ty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Repetitive use of this tool should be avoided.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle

oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 4 of 6

Revision: A Revision ate: 06-06-11

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above).

Variations in tools, terminals, wire stranding, and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all

insulation sizes.

4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts

available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no

influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips

on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping

Handbook 63800-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

Applicatio s for the Modular Crimp Head

WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction

and without first reading and understanding the instructions in the proper Manual or Specification Sheet.

See Chart below for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. isconnect the

power by unplugging or turn off the Actuator from its power source.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle

oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 5 of 6

Revision: A Revision ate: 06-06-11

MODULAR

CRIMP

HEAD

BATTERY

POWER

CRIMP

ADAPTER

LOCKING

PINS

LOCKING PINS

BATTERY

POWERED

TOOL

AIR

POWER

TOOL

MODULAR

CRIMP HEAD

LOCKING

PINS

LOCKING

PINS

AIR

POWER

CRIMP

ADAPTER

The chart below shows all applications for this Modular Crimp Head.

Modular Crimp Head

Order No.

Tool

Order o.

Tool

Descriptio

Adapter

Order No.

Adapter

Descriptio

Figure

No.

63823-8570

63816-0000

Hand Crimp Frame (Short) N/A N/A 3

63816-0050

Hand Crimp Frame (Long) N/A N/A 3

63816-0200

Battery Power Tool (110 V)

63816-0600

Battery Power Crimp Adapter

63816-0250

Battery Power Tool (220 V)

63816-0600

Battery Power Crimp Adapter

63816-0100

Air Power Tool 63816-0700

Air Power Crimp Adapter 5

Applicatio s for the Modular Crimp Head

Ha d Crimp Tool Battery Powered Tool Air Powered Tool

Figure 3 Figure 4 Figure 5

MODULAR

CRIMP

HEAD

LOCKING

PINS

HAND CRIMP

FRAME LONG

OR SHORT

Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle

oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 6 of 6

Revision: A Revision ate: 06-06-11

RATCHET

RELEASE LEVER

HANDLE

SPRING

CRIMPING

SPRING (2)

Figure 6

M4 X 14mm

LONG BHCS

PARTS LIST

Ha d Crimp Tool 63823-8500

Item

Order Number

Descriptio Qua tity

1 63823-8570 Modular Crimp Head 1

2 63816-0050 Hand Crimp Frame (Long)

3 63823-8575 Locator 1

4 63816-0001 Locking Pin 2

5 63600-0525 Handle Spring 1

6 63600-0520 Crimping Spring 2

http://www.molex.com

Other manuals for 207129 Series

100

This manual suits for next models

Table of contents

Other molex Crimping Tools manuals

Popular Crimping Tools manuals by other brands

Panduit

Panduit CT-1000 Operation & instruction manual

JST

JST CS 10 instruction manual

Danfoss

Danfoss ET4200 Operator's manual

Tyco Electronics

Tyco Electronics PRO-CRIMPER III instruction sheet

TE Connectivity

TE Connectivity 2063528-1 instruction sheet

Tyco Electronics

Tyco Electronics 69156-1 instruction sheet

CRH

CRH CRL CBLHCT1 instruction manual

Emerson

Emerson Klauke ES 105CFM manual

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Operating instructions manual

Danfoss

Danfoss ET4350 Operator's manual

Milwaukee

Milwaukee M18 Operator's manual

HOGERT

HOGERT HT1P169 user manual

Textron

Textron ESG105L instruction manual

Tyco Electronics

Tyco Electronics 90035-3 instruction sheet

Emerson

Emerson Klauke ES 20RMCCFB manual

Continental Refrigerator

Continental Refrigerator PC150HD quick start guide

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 instruction sheet

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 instruction sheet

molex 207129 Series User manual

Popular Crimping Tools manuals by other brands