ML Accessories RW6WW Instruction Manual

INSTALLATION & MAINTENANCE MANUAL

RW6WW / RW6CW / RW6CCT

These instructions should be read carefully and retained after installation by the

end user for future reference and maintenance.

These instructions should be used to aid installation of the following products:

RW6WW / RW6CW / RW6CCT

GENERAL INSTRUCTIONS

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building Regulations. If in any doubt, consult a

qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is ﬁtted) does not exceed

the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location

for installation

• If used under insulation, the insulation should be laid unbroken over the luminaire (not

packed around it). Only mineral wool style insulation may be used

• This product is for indoor use only

• This product is Class I and must be earthed

• This product is IP65 rated (IP20 from above)

INSTALLATION

Note - If this product is being used in conjunction with an external PIR or sensor, please

conﬁrm with the manufacturer of the sensors that they are compatible with LED luminaires.

•Provide power to the required point of installation

•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring

not to infringe with any joists, gas/water pipes or electrical cables

Fig. 1

RW6 Series

These instructions should be read carefully and retained after installation by the end user for future

reference and maintenance.

These instructions should be used to aid installation of the following products:

RW6WW / RW6CW / RW6CCT

SAFETY

•Installation of this luminaire should only be carried out by a qualified electrician or

competent person to the latest Building and current IEE Wiring Regulations (BS7671)

•Please isolate mains prior to installation/maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not

exceed the rating of the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress of Protection) rating of this luminaire when deciding the

location for installation

•We recommend a 50mm spacing around and above the fitting for air dissipation

•This product is Class I and must be earthed

•This product is dimmable with most trailing edge dimmers

•This product is IP65 rated

INSTALLATION

Note: If this luminaire is being used in conjunction with external PIR or sensors, please confirm with

the manufacturer of the sensors that they are compatible with LED luminaires.

•Provide power to the required point of installation. Suitable IP rated junction boxes should

be used where required

•Cut a suitable hole in the ceiling as per the cut-out details in Fig 1 ensuring that it does not

infringe with electrical cables, water/gas pipes or ceiling joists

Fig 1

72mm

•With the aid of a cross-head screwdriver, remove the cover to access the mains terminal

block (see Fig 2)

Fig 2

•Connect the luminaire to the mains supply ensuring that correct polarity is observed

L - Live (brown) E - Earth (yellow/green) and N - Neutral (blue) (see Fig 3)

Fig 3

• With the aid of a cross-head screwdriver,

remove the cover to access the mains

terminal block (see Fig. 2)

• Connect the luminaire to the mains supply ensuring that correct polarity is observed:

L - Live (brown) E - Earth (yellow/green) and N - Neutral (blue) (see Fig. 3)

•Two cables can be inserted into the push-ﬁt terminal block in order to achieve loop

in/loop-out wiring

Fig. 2

Fig. 3

•With the aid of a cross-head screwdriver, remove the cover to access the mains terminal

block (see Fig 2)

Fig 2

•Connect the luminaire to the mains supply ensuring that correct polarity is observed

L - Live (brown) E - Earth (yellow/green) and N - Neutral (blue) (see Fig 3)

Fig 3

•Lift both of the spring clips on the sides of the ﬁtting and push into the ceiling

•Switch on and check for correct operation

Fig. 4

ADJUSTABLE CCT FITTING ONLY (RW6CCT)

COLOUR CHANGE

• To change the colour temperature of the ﬁtting, switch the ﬁtting on, off, and on again

within 2 seconds. Repeat this switching cycle until desired colour temperature has been

achieved (see Fig. 4)

•Refit the terminal cover and tighten screw ensuring that the strain relief grips the cable

securely

•To remove the bezel turn anti-clockwise

•To refit the bezel turn clockwise

•Hold back springs and insert fitting into ceiling

•Switch on power supply and check for correct operation

ADJUSTABLE CCT FITTING ONLY (RW6CCT)

COLOUR CHANGE

•To change the colour temperature of the fitting, switch the fitting on, off and on again within

2 seconds. Repeat this switching cycle until desired colour temperature has been achieved

(see Fig 4)

Fig 4

MEMORY FUNCTION

•The luminaire will always remain the same colour temperature until the above switching

cycle has been carried out

RESET FUNCTION

•To reset the fittings back to warm white, turn on the fittings and leave them on for 5

seconds

WARRANTY

This product has a warranty of 5 years from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper

use, or removal of the batch code will invalidate the warranty. If this product should fail

within its warranty period, it should be returned to the place of purchase for a free of

charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

GENERAL

WARNING

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which

may damage the product.

This product is dimmable using trailing edge dimmers, please check compatibility before

installation.

The light source of this luminaire is not replaceable; when it reaches its end of life the whole

luminaire should be replaced.

This product should be recycled in the correct manner when it reaches the end of its life.

Check local authorities for where facilities exist.

This product must be disconnected from the circuit if subjected to any high voltage or

insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

MEMORY FUNCTION

• The luminaire will always remain the same colour temperature until the above switching

cycle has been carried out

RESET FUNCTION

• To reset the ﬁttings back to warm white, turn on the ﬁttings and leave them on for 5

seconds

• Switch the ﬁttings off/on 4 times within 6 seconds

• Upon the 4th “on” switch, all luminaires will revert back to warm white

DCJUL21_V4

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

118

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

This manual suits for next models

Table of contents

Other ML Accessories Lighting Equipment manuals

ML Accessories

ML Accessories SPIKE5S Instruction Manual

ML Accessories

ML Accessories NH0183BD Instruction Manual

ML Accessories

ML Accessories BA01 Series Instruction Manual

ML Accessories

ML Accessories Knightsbridge BT9H4/6K Instruction Manual

ML Accessories

ML Accessories CAPWGU Instruction Manual

ML Accessories

ML Accessories Knightsbridge SPIKEW Manual

ML Accessories

ML Accessories Knightsbridge SFPL Series Instruction Manual

ML Accessories

ML Accessories WALL1 Instruction Manual

ML Accessories

ML Accessories TRIBCCW Instruction Manual

ML Accessories

ML Accessories AXREMC Instruction Manual

ML Accessories

ML Accessories AX CCT Instruction Manual

ML Accessories

ML Accessories BF1430S Instruction Manual

ML Accessories

ML Accessories AC65118 Instruction Manual

ML Accessories

ML Accessories ENM5 Instruction Manual

ML Accessories

ML Accessories SHE1B Instruction Manual

ML Accessories

ML Accessories OWALL1 Series Instruction Manual

ML Accessories

ML Accessories SUR5LED Instruction Manual

ML Accessories

ML Accessories ENM5C Instruction Manual

ML Accessories

ML Accessories BL01BK Instruction Manual

ML Accessories

ML Accessories EA1 Series Instruction Manual

ML Accessories

ML Accessories SHE1BEM Instruction Manual

ML Accessories

ML Accessories EMLSUS Instruction Manual

ML Accessories

ML Accessories NCLB12 Instruction Manual

ML Accessories

ML Accessories WP15CTP Instruction Manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions