MinimumRC ASG-32 User manual
ASG-32 Glider
Assembly Instructions
Important notification
1.The model is supplied with UFO and 502 glue. UFO is for bonding foam parts, and 502 for
bonding wood, carbon fiber and metal parts. 502 glue will cause serious corrosion to foam parts.
2.Please wait for the glue to dry and solidify in each installation step before the next ins tallation.
3.Please avoid using flame to heat the heat shrinkable tube on the model. Electric iron shall be
used for heating.
4.Please use razor blade to remove the parts from the plate. Do not tear the parts by force.
1. Fuselage internals
2. Bond the inner structure of the fuselage with 502 glue.
Please pay attention to the opening direction of the servo base.
3. Combined motor base, use 502 glue to fix the motor.
4. Use m1.2x6mm screw to fix the turnover motor base. Adjust the distance between the fixed
pieces on both sides of the motor base till the motor base can be turned over freely. If necessary,
sand the motor base to reduce its thickness to make the turning movement smooth.
5. Screw in another m1.2x6 screw from the right side to form the motor line limit to prevent the
motor line from interfering with the motor base movement or propeller running.
6.Connect the servos to a powered receiver. Bind the receiver with your transmitter to make the
servos return to their neutral point. Test whether the servos are working normally, and install the
servo arms according to the position shown in the picture. (use screws to fix the servos on the
servo base from the top.)
Note: Please make sure that the servos have been tested and installed in strict accordance with
the following picture. After assembling the model, it will be not able to adjus t.
7. Install the receiver. No glue is required here.
8.Connect the cable of servos and motor, and connect the receiver to power for test. Ensure that
the servos and motor work normally and the motor rotation direction is correct.
Secure the cable with ties.
Note: please make sure the motor rotation direction is correct. After the model is assembled, it
cannot be adjusted.
9. Combine the fuselage inner structure with the right panel of the fuselage.
Note: the bottom of inner structure (red circles) should be 2mm away from the edge.
10. Use the end of a carbon fiber rod to score through the half -cut line of the tail surface.
11. As shown in the figure, glue the fuselage side strips (and vertical tail) to the inside of the right
fuselage side panel in the order of A-B-C-D-E-F.
·The fuselage side strips are made of flexible material, which can be bent before bonding.
·In strict accordance with the A-B-C-D-E-F sequence installation, can ensure the accurate position
of the fuselage side strips.
·The fuselage side strips should be aligned with the fuselage side plate contour, which is helpful
to the model aesthetics.
12. The installation of fuselage side plate is completed, as shown in the figure.
Take 200 mm conduit and two duct seats for elevator drive.
13. As shown in the figure, paste a conduit seat inside the right side of the fuselage. The distance
between the seat and the conduit hole on the side plate is about 30mm.
14. As shown in the figure, paste a duct seat on the right side of the vertical tail. This guide
socket is used to fix the end of elevator drive pipe.
The blue curve in the figure shows the route of elevator conduit pipe and steel wire.
15. Glue the conduit to the conduit base inside the fuselage, and the two ends of the conduit pass
through the two conduit holes on the right side of the fuselage.
Left end of the guide pipe extends out of the fuselage by 5mm.
16. Glue the end of the duct to the duct seat on the vertical tail.
17. Install the duct on the left side of the fuselage as shown.
Take one 170mm conduit and one duct base.
Paste the duct base inside the left side of the fuselage, 30mm away from the duct hole.
18. Glue the conduit to the conduit base on the left side of the fuselage, both of the ends of the
conduit pass through the conduit hole.
Other MinimumRC Toy manuals
MinimumRC
MinimumRC Shrimp V2 User manual
MinimumRC
MinimumRC F8F Rare Bear Manual
MinimumRC
MinimumRC T-34 Mentor User manual
MinimumRC
MinimumRC T-34 Mentor User manual
MinimumRC
MinimumRC Ju-87 User manual
MinimumRC
MinimumRC Flycat User manual
MinimumRC
MinimumRC F8F-RareBear Pro User manual
MinimumRC
MinimumRC Piper Cub J-3 User manual
MinimumRC
MinimumRC Messerschmitt BF-109 User manual
MinimumRC
MinimumRC J-3 User manual
MinimumRC
MinimumRC P40 Q Series User manual
MinimumRC
MinimumRC Beech V-35 User manual
MinimumRC
MinimumRC Butterfly V1 User manual
MinimumRC
MinimumRC LISA User manual
MinimumRC
MinimumRC Cessna L-19 User manual
MinimumRC
MinimumRC Sopwith Camel User manual
MinimumRC
MinimumRC Tigermoth User manual
MinimumRC
MinimumRC PZL106 Q Series User manual
MinimumRC
MinimumRC NANCHANG CJ-6 User manual
MinimumRC
MinimumRC P-51 Mustang User manual
