Mikado LOGO 10 User manual

Mikado Modellhubschrauber • Clara-Zetkin-Str.8 • 14471 Potsdam • Germany

Phone +49 331 95130280 • Fax +49 331 95130281 • www.Mikado-Heli.de

Modellhubschrauber

www.Mikado-Heli.de

Manual

LOGO 10

Modellhubschrauber

Manual

LOGO 10

Page2 ©MikadoModellhubschrauber

Index

1 Main Frame .........................................6

1.1 Motorplate 6

1.2 Main Frame 7

1.3 Bearing Case 8

2 Landing Gear.....................................9

3 Motor Installation .............................10

3.1 Motor Adaptor Plate 10

3.2 Motor Attachment 11

4 Main Gear ..........................................12

4.1 Hub 12

4.2 Adjusting Gear Backlash 13

5 Tail Rotor............................................14

5.1 Tail Rotor Shaft 14

5.2 Vertical Fin 15

5.3 Pitch Slider 16

5.4 Tail Rotor Lever 17

5.5 Tail Rotor Hub 18

5.6 Final Assembly 19

6 Tail Boom...........................................20

6.1 Tail Boom Assembly 20

6.2 Tail Boom Holder 21

6.3 Tail Drive Pulley 22

6.4 Tail Control Rod 23

6.5 Installation 24

6.6 Horizontal Fin 25

6.7 Tail Rotor Blades 25

7 Finished Main Frame & Tail Boom.26

8 Preparation for Servo Installation .27

8.1 120° CCPM 27

8.2 90° CCPM 27

8.3 Servo Arms 28

8.4 Servo Centering 28

8.5 Linkage 29

9 Servo Installation .............................30

9.1 Tail Rotor Servo 30

9.2 Elevator Servo 31

9.3 Elevator Linkage/Swashplate 32

9.4 Canopy Fixing Bolts 32

9.5 Aileron Servo left 33

9.6 Aileron Servo right 34

9.7 Aileron Linkage 35

10 Wash-Out Hub ................................36

10.1 Assembly 36

10.2 Installation 37

11 Main Rotor Head ............................38

11.1 Blade Grips 38

11.2 Mixing Arms 38

11.3 Yoke 39

11.4 Seesaw 40

11.5 Flybar Control Bridge 41

11.6 Ball Bolts 41

11.7 Flybar 42

11.8 Flybar Paddles 42

11.9 Final Assembly 43

11.10 Rotor Head Linkage 44

12 Logo 10 assembled.......................46

13 RC Installation................................47

13.1 Receiver, Gyro, Speed Controller 47

13.2 Battery 48

14 RC Programming ...........................49

15 Canopy............................................55

15.1 Trimming and Taping 55

15.2 Decals 56

16 Rotor Blades...................................57

17 Final Pre-Flight Check ..................58

17.1 Direction of Main and Tail Rotation 58

17.2 Blade Tracking Adjustment 58

18 Control Movements.......................59

18.1 Pitch/Throttle 59

18.2 Rudder 59

18.3 Elevator 60

18.4 Aileron 60

19 Overview ........................................61

19.1 Chassis 61

19.2 Rotor Head 62

19.3 Tail Boom/Tail Rotor 62

19.4 Upgrades/Accessories 63

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160mm

123456

inches

Manual

LOGO 10

Page3 ©MikadoModellhubschrauber

Safety Instructions

OPERATING YOUR MODEL SAFELY

Operate the helicopter in spacious areas with no people nearby.

! Warning: Do NOT operate the helicopter in the following places and situations

(or else you risk severe accidents):

in places where children gather or people pass through

in residential areas and parks

indoors and in limited space

in windy weather or when there is any rain, snow, fog or other precipitation

If you do not observe these instructions you may be held reliable for personal injury or property damage!

Always check the R/C system prior to operating your helicopter.

When the R/C system batteries get weaker, the operational range of the R/C system decreases. Note that you

may lose control of your model when operating it under such conditions.

Keep in mind that other people around you might also be operating a R/C model.

Never use a frequency which someone else is using at the same time. Radio signals will be mixed and you will

lose control of your model.

If the model shows irregular behavior, bring the model to a halt immediately. Turn off all power switches and

disconnectthebatteries.Investigate the reason and fixtheproblem.Do not operate the modelagainaslong as the

problem is not solved, as this may lead to further trouble and unforeseen accidents.

! Warning: In order to prevent accidents and personal injury, be sure to observe the following:

Beforeflyingthe helicopter, ensure thatall screwsare tightened.Asingle loose screwmaycause amajor accident.

Replace all broken or defective parts with new ones, as damaged parts lead to crashes.

Never approach a spinning rotor. Keep at least 10 meters/yards away from a spinning rotor blades.

Do not touch the motor immediately after use. It may be hot enough to cause burns.

Perform all necessary maintenance.

PRIOR TO ADJUSTING AND OPERATING YOUR MODEL, OBSERVE THE FOLLOWING

!Warning:Operate the helicopter only outdoors and out of people’s reach as the main rotor operates at high rpm!

! Warning: While adjusting, stand at least 10 meters/yards away from the helicopter!

Novice R/C helicopter pilots should always seek advice from experienced pilots to obtain hints with assembly

and for pre-flight adjustments. Note that a badly assembled or insufficiently adjusted helicopter is a safety hazard!

In the beginning, novice R/C helicopter pilots should always be assisted by an experienced pilot and never fly

alone!

Throttle channel should be in motor OFF position while powering up.

When switching the R/C system ON or OFF, always proceed in the following order:

When switching ON:

Position the throttle control stick (on transmitter) to a position where the LOGO 10 motor does not operate.

Turn on the transmitter.

Turn on the receiver.

Connect the motor battery.

Operate your model.

When switching OFF:

Turn off the motor (move throttle control to a position where motor does not operate).

Wait until the rotor head has stopped spinning.

Disconnect the motor battery.

Turn off receiver.

Turn off transmitter.

Manual

LOGO 10

Page4 ©MikadoModellhubschrauber

Tools for Assembly & R/C Equipment

Scissors

Rubber Hammer

Drill with

1.5mm bit

(.059 in)

Marker

Screwdrivers

(plus and minus)

Hex Wrenches

1.5/2.0/2.5/3.0mm

(.055/.079/.098/.118in)

Radio with Heli-Software

4x Mini Servos (Graupner DS361

or Graupner C341)

Receiver Battery

(Sanyo AR500)

Battery (Sanyo RC2400 or Sanyo 3000 NiMH)

Receiver (Graupner DS 19

or SMC 19 SPCM)

Gyro (Futaba GY240

or GY401)

Fast Charger (Schulze isl 6-330d or isl 6-636+)

Motor + Speed Controller (check the Mikado

webpages for recommended motors)

Alle shown products are examples.You may use different brands.

Ball link pliers

Threadlock

BEC, replaces

receiver battery

Manual

LOGO 10

Page5 ©MikadoModellhubschrauber

Listing of Parts

Chassis, Bag 1 1965 3 socket head cap screw M3 x 18

1914 2 countersunk screw M4x10 2013 2 washer 4 x 8 x 1

1915 2 countersunk screw M3 x 8 2064 8 self-tapping screw 2.9 x 16

1953 6 socket head cap screw M3 x 10 2074 1 hex locknut M3

1961 1 cylinder screw M3x35 2370 2 hex spacer 27 mm

1964 2 socket head cap screw M3 x 12 flat head 2370 2 hex spacer 23 mm

2012 2 washer 3 x 7 x 0,5 2485 1 tail boom holde

2062 4 self-tapping screw 2.9 x 13 2488 1 cylindrical pin 4 x 31.5

2064 2 self-tapping screw 2.9 x 16 2491 1 horizontal stabilize

2072 8 hex nut M3 2728 1 driven belt gear, 40 Z

2189 1 rod end 8 mm 2760 1 tail boom 565 mm

2370 1 hex spacer, 38 mm 2762 1 tail rotor rod, 545mm

2370 2 hex spacer, 19 mm 2763 2 rudder control guide

2384 1 thread rod M3

2724 2 O-ring battery holders, 38x3,5 + 46x3,5 Main Rotor Head, Bag 7

2379 1 motor plate 909 1 yoke

2380 1 bearing case 933 1 stabilizer control bridge

2382 2 canopy fixing bolt 935 1 seesaw

2383 1 swashplate guide bracket 2314 2 blade holde

2499 1 motor adaptor plate 2346 1 rotorhead shaft

2720 1 LOGO 10 mainframe right 2358 2 stabilizer blade 3 mm

2721 1 LOGO 10 mainframe left 2361 2 ball bolt

912 2 pin

Main Gear, Bag 2 939 1 seesaw bolt

1344 1 C-Ring 965 2 double ball-link

1915 4 countersunk screw M3 x 8 1570 4 balls

1940 3 socket head cap screw M4x5 1900 2 cylinder screw M2 x 3

2010 2 washer 10x16x0,5 1902 8 cylinder screw M2 x 8

2386 1 fixing colla

1903 4 cylinder screw M2 x 10

2725 1 main gear, 200 teeth 1921 2 set screw M3 x 3

2731 1 one-way hub 1956 2 socket head cap screw M3 x 16

2740 1 main rotor shaft 1965 1 cap screw (yoke) M3 x 18

1972 2 socket head cap screw M3 x 12

Wash-out / Swashplate Bag 3 1975 2 cap screw (blade holder) M3 x 25

969 1 washout-block 2012 4 Washer 3x7x0,5

978 2 mixing arm for slide bearing 2015 2 washer 4 x 12 x 1

980 2 bolt for no. 981 2070 4 hex nut M2

981 2 Y-rod 2072 1 hex nut M3

982 2 bolt + e-ring 2074 2 hex locknut M3

1570 2 ball 2320 2 mxing arm, slide bearing 3x5x6

1902 2 cylinder screw M2 x 8 2750 1 stabilizer bar 360 mm

2365 2 swashplate 2755 6 dumper rubber 8x2,5 (4x), 7x2,5 (2x)

Tail Rotor, Bag 5 Landing frame, Bag 8

1570 1 ball 1954 4 socket head cap screw M3 x 12

1902 1 cylinder screw M2 x 8 2012 4 washer 3 x 7 x 0,5

1921 1 set screw M3 x 3 2074 4 hex locknut

1953 1 socket head cap screw M3 x 10 2495 2 landing gear strut

1954 2 socket head cap screw M3 x 12 2775 2 landing gear skid

1955 3 socket head cap screw M3 x 14

1958 2 socket head cap screw M3 x 25 Control rods, Bag 9

2004 2 washer 5 x 10 x 0.1 1567 6 ball-links 2.5 mm

2074 5 hex locknut M3 1569 2 ball-links, angular 2.5 mm

2442 1 tail rotor case 1570 4 ball

2446 1 tail rotor lever + washer 3x4x10,5 1586 4 control rod 60 x 2.5 mm

2450 1 tail rotor pitch plate 1902 4 cylinder screw M2 x 8

2452 1 control ring 2070 4 hex nut M2

2455 1 control sleeve 2770 3 control rod 30 x 2,5mm (swashplate)

2458 1 tail rotor housing

2460 1 tail rotor blades Ball Bearings, Bag 10

2462 2 tail rotor blade holde

937 3 ball bearing 4 x 13 x 5

2463 2 bushing 3 x 5 x 2.1 941 2 ball bearing 3 x 10 x 4

2466 1 driven belt gea

1329 2 ball bearing 10 x 19 x 5

2467 1 gear drive

1440 2 ball bearing 6 x 10 x 2,5

2468 1 driving pin 2 x 8 mm 2351 4 ball bearing 8 x 14 x 4

2476 1 tail rotor shaft 2423 4 ball bearing 3 x 8 x 3

2490 1 vertical stabilize

2470 2 ball bearing 5 x 10 x 4

2765 1 driven belt 490 XL 2489 1 ball bearing 4 x 9 x 4

Tail Boom, Bag 6 2478 1

ntenna tube

1560 2 ball link 2 mm 2790 1 LOGO 10 canopy

1921 1 set screw M3 x 5 2792 1 decals LOGO 10

Manual

LOGO 10

Page6 ©MikadoModellhubschrauber

#2379

1x 10x19x5 #1329

6x M3 #2072

1 Main Frame

1.1 Motorplate

Bag 1 • Bag 10

Manual

LOGO 10

Page7 ©MikadoModellhubschrauber

#2720

#2721

6x M3x10 #1953

2x 2,9x16 #2064

1x 38 mm #2370

1x M3x35 #1961

#2189

1 Main Frame

Please avoid overtightening the

2.9x16 mm selftapping screws and

the socket head cap screw M3x35

when drilling them into the plastic

side-frames.

Use the 8 mm ball end #2189, so

you have the option of attaching the

tailboombracelater(#2761,notinclu-

ded in the kit), if desired.

1.2 Main Frame

Bag 1

Manual

LOGO 10

#2380

1x 10x19x5 #1329

2x 19 mm #2370

4x 2,9x13 mm

#2062

1 Main Frame

Please avoid overtightening the

2.9x13 mm selftapping screws when

drilling them into the plastic side-fra-

mes.

1.3 Bearing Case

Bag 1 • Bag 10

Manual

LOGO 10

#2495

#2775

4x M3x12 #1954

4x M3 #2074

4x 3x7x0,5 #2012

2 Landing Gear

Bag 8

Align the skids and secure them

with superglue.

Manual

LOGO 10

#2499 2x M3x8 #1915

3 Motor Installation

3.1 Motor Adaptor Plate

Bag 1

Some electric motors (e.g. Kontro-

nik, Plettenberg, Speed 700 Neody-

me motors) are constructed such

that they cannot be moved along the

motor plate. If you are using one of

these motors, please use the motor

adaptor plate #2499.The plate is not

needed for Hacker motors.

Please check from the Mikado

website which pinion works best with

the motorset you have (on

www.mikado-heli.de go to LOGO 10

and click “Motorization”). When a

wrong pinion is chosen, the perfor-

mance of your electric helicopter will

deteriorate and the motor or speed

controller can be damaged.

Donottightenthesetscrewfullyuntil

the final position of the pinion on the

motor shaft is determined. This is

done after installing the main gear.

There are two options for attaching

thepinion:

1. For securing the pinion, you may

flatten the motor shaft where the set

screwmeets the motor shaft -without

making a flat surface on the motor

shaft.

2. Alternatively, you may screw the

set screw directly onto the motor

shaft. For this it is required that the

set screw has an appropriate rim for

engaging the motorshaft (all Mikado

pinionshavethisrim).Note,however,

that after attaching the set screw

once,the rimbecomesbluntandmay

not be used again.

Table of contents

Other Mikado Toy manuals

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Build instructions

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

iKarus

iKarus ECO 8 Assembly instruction

Multiplex

Multiplex EasyStar II Building instructions

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

Meccano

Meccano 15103 instructions

LEGO

LEGO TECHNIC 8735 instructions