METHVEN AIO User manual

Methven warrants this product against manufacturing defects and that it is suitable for use

under the general operating conditions speciﬁed in this instruction sheet. However, regional

regulations apply and may aﬀect your warranty. Please refer to www.methven.com or call

customer service for full details.

New Zealand

0800 804 222

Australia

1300 638 483

0800 195 1602

www.methven.com

Never use abrasives or abrasive cleaning agents to clean this product. Clean regularly with

contamination free warm soapy water and a damp soft cloth.

Care and Cleaning:

Step 5

Screw the grub screw into the diverter knob, ensuring it

does not protrude out of the knob or into the threads.

Rotate the brass diverter spindle fully

counter-clockwise.

Screw the knob onto the brass diverter spindle until it

touches the faceplate. Unscrew approximately 1mm (1

turn) to a position such that the handle of the knob is

pointing vertically upwards.

To secure the diverter knob, tighten grub screw ﬁrmly

with the hex key provided.

•

Step 6

Push handle on to cartridge lever, and tighten grub

screw ﬁrmly with hex key provided.

•

435931 ISSUE A

Technical Speciﬁcations:

Operating Pressure:

Min: 150kPa/1.5bar

Max: 1000kPa/10bar*

Optimum: 150kPa/1.5bar - 500kPa/5bar

Operating Temperature:

Hot: Max 80°C*

Cold: Min 5°C

Inlet Connections:

All ½" BSP

* Regional speciﬁc regulations apply.

Please refer to your warranty statement at

www.methven.com

AIO SHOWER MIXER WITH DIVERTER

Installation Guide

Hot

Cold

Outlet 2

50-55mm

65mm ±10

Outlet 1

75mm

55-60mm

Step 1

Leave plastic covers in place during the installation.

Secure the mixer body to the supporting timber

ensuring that it is oriented square and vertical.

IMPORTANT: Before you begin, turn oﬀ the water supply.

•

Step 2

Flush all pipe-work thoroughly prior to the next step.

Connect hot and cold supplies and outlets to mixer

body ensuring a good seal at each joint.

Leak test installation prior to closing wall cavity.

The seal integrity of pipe joins are the responsibility

of the installing plumber.

•

Step 3

Wall lining hole should be cut or ﬁnished as per the

dimension shown in the diagram on the right.

Optimum distance from mounting surface to ﬁnished

wall surface = 65mm ±10

•

Step 4

Remove plastic covers.

Ensure that the faceplate locator is ﬁtted to the small

hole in the faceplate.

Apply silicone to the faceplate to create a seal with

the ﬁnished wall surface.

Slide o-ring, then faceplate onto mixer body.

•

Mixer Body Assembly

O-ring

Faceplate

Handle

Grub Screw

Hex Key

Grub

Screw

Diverter

Knob

Faceplate

Locator

•

IMPORTANT: Please read all of the instructions before installation.

General:

Methven recommends this product is installed by a licensed plumber in compliance with all

relevant regional regulations.

Do not hydrostatic test the installation with this mixer installed. Damage to the ceramic cartridge

may occur.

All pipe work must be thoroughly ﬂushed prior to the installation of the mixer.

In-line ﬁlters must be ﬁtted on both hot and cold supplies to prevent foreign particles damaging

the ceramic cartridge.

Do not remove the ceramic cartridge from the mixer when installing.

After installation all connections must be checked for leaks.

All outlets used primarily for personal hygiene shall deliver water at a safe temperature as per

regional regulations.

This mixer is not recommended for use in uncontrolled heating systems such as wet-backs or

solar heating units unless a suitable tempering valve is ﬁtted.

It is the responsibility of the installer to ensure a waterproof seal is achieved between the

product and mounting surface. If in doubt about the quality of the seal, remove the product and

reinstall using silicone to ensure a seal is achieved.

Other METHVEN Kitchen & Bath Fixture manuals

METHVEN

METHVEN Kiri 113 User manual

METHVEN

METHVEN Deva IND104 User manual

METHVEN

METHVEN MAKU BASIN MIXER User manual

METHVEN

METHVEN AURAJET User manual

METHVEN

METHVEN ALBSMCP User manual

METHVEN

METHVEN SHOWER VALVES WITH DIVERTERS User manual

METHVEN

METHVEN Breeze BRBSMCPUK User manual

METHVEN

METHVEN SATINJET User manual

METHVEN

METHVEN AIO BASIN MIXER User manual

METHVEN

METHVEN Aio Shower Mixer with Fastflow User manual

METHVEN

METHVEN Deva Vision VSN104 User manual

METHVEN

METHVEN KAHA 3 User manual

METHVEN

METHVEN MINIMALIST MK2 User manual

METHVEN

METHVEN 01-8444 User manual

METHVEN

METHVEN SURFACE BASIN MIXER User manual

METHVEN

METHVEN Amio 01-4057 User manual

METHVEN

METHVEN Aio AOBCP User manual

METHVEN

METHVEN KOHA User manual

METHVEN

METHVEN Waipori 01-8185 User manual

METHVEN

METHVEN Indra INBFCPUK User manual

METHVEN

METHVEN 01-8123 User manual

METHVEN

METHVEN Kaha 113 User manual

METHVEN

METHVEN Aroha 01-9106 User manual

METHVEN

METHVEN ROUND RAIL User manual

Popular Kitchen & Bath Fixture manuals by other brands

Grohe

Grohe BRIDGEFORD 33 870 manual

Hans Grohe

Hans Grohe Zenio Metro 31811000 manual

Gröne

Gröne Zedra 32 555 manual

Transform

Transform QL045 owner's manual

Sanela

Sanela SLU 09PTB Instructions for use

Glacier bay

Glacier bay FP4A0052BNV Installation and care guide

Lefroy Brooks

Lefroy Brooks C1-1400 Installation, operating, & maintenance instructions

Grohe

Grohe Rapido E installation manual

Danze

Danze D302455 quick start guide

Waterworks

Waterworks CEKM30 Installation guidelines

Helvex

Helvex Omega TV-298 installation guide

Tribata.

Tribata. GEORGIAN G5393 manual

Alpha Bidet

Alpha Bidet Alpha One user manual

InSinkErator

InSinkErator H/HC3300 Installation, care & use

Clou

Clou Xo type 1 installation instructions

Kohler

Kohler Contra 26448T-4 installation instructions

Grohe

Grohe Bridgeford 20 158 manual

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Instructions for use and assembly instructions