MERLYN MB2 User manual
NOTE: Please ensure the bathscreen
Is installed on the inside of the bath top.
inside edge
MB2
BT003 / T-027
Fixing Kit components
- PH2 Philips Head screw driver
Neutral cure anti bacterial silicone
13
2SS008
Wall prafile cover
Clear Seal
2SP0MOBY002L/R
1
1
1
Wall profile LR8387C
Hinge post S030C
A
1
Moving Glass Panel
Wall Plug 2SP12
3
3
3
3
3
Screw(4X40mm)
Screw Cover Cap
Screw Cover Cap Clip 2SS009
1
2
1
Screw(3.5X30mm)
SP0MOBY002L/R
2
1
3
4
6
7
9
8
10
11
13
2
5
12
15
1
16
15
1
1
14
SP0LFTPS SP0LFBPS
Top pivot sleeve
Bottom pivot sleeve
x1 x1
SP0LFBPS
SP0LFTPS
SP0LFCS
SP0LF02
Bracket bottom Leakfree
Bracket top Leakfree SP0LF01
14
16
foam plastics
1
LP-123
SP0M7029
LP-123
x1
Top Bracket
SP0LF01
Bottom Bracket
SP0LF02
x1
x1
4x40
A2403001
4x12
A2401201
Screw(4X12mm)
A2403001
A2401201
1. Ensure your bath is level before fitting.This screen is not designed to fit on baths with stepped fronts,roll top rims or integral soap dishes.
Fig 1
1A
1B 1D
1C
1.Bathscreen is reversible, choose which handing is required ensuring that the glass coated side is always
on the inside of the bath.Silicone the top pivot bracket and bottom pivot bracket, and then insert into the
round profile. Fig 1, 1A-1D.
2A
2B
2C 2D 2E
Fig 2
TOP
BOTTOM
OUTS IDE
OUTSI DE
OUTSIDE
TOP
BOTTOM
Bottom
Top
2. Unscrew the top pivot bracket SP0LF01 and insert panel A, reattach the pivot bracket.Fig 2.
Note: Ensure pivot bracket SP0LF02 is always on the bottom of the product
Top Bracket
SP0LF01
Bottom Bracket
SP0LF02
To help fit the bottom seal, turn the screen upside down. Apply silicone as shown in fig 3A. Fit seal SP0LFCS
on to the bottom of the bath screen Fig 3 ensuring to push the end of the seal fully into the bottom bracket .
NOTE: Silicone behind
the wall profile on the
bath edge if not siliconed
previously
edge
screen
lnside
lnside
lnside
lnside
lnside
3E
3A
3B
3C
3D
Fig 3
Fig 4
bath.Fig 4.
fix wall profiiles to wall.Fig 5.
4.
5.5.
LR8387C
LR8387C
Bottom
Top
6 mm
x3
5A
5B
5C
5D
Fig 5
3.
Screw A2403001,
6.
where the wall profile and hinge bracket sit on the bath inside and outside.
Seal around the end of the seal as shown and approx 50mm between the glass and profile.
7A
Inside and outside :
OUTSIDE
Fig 6
x3
6
7B
8
SP0MOBY002L/R.
8. bath.
Outside
lnside
Outside
Fig 7
Sealing.Fig 7
When installation is complete seal the joint between the wall profile and the wall,top to bottom.
Seal 50mm up where
Outside only
Silicone
the hinge upright and the wall profile over lap.
7. Drill 3 holes top,middle and bottom through the wall profile and hinge upright using a 3mm steel drill bit. Using the Screws
A2401201,and screw cover caps 2SS008 and screw cover caps clips 2SS009 fix the hinge upright to the wall profile in 3
places.Fig 6.
50mm
Outside lnside
Other MERLYN Bathroom Fixture manuals
MERLYN
MERLYN EASY CORNER DOOR User manual
MERLYN
MERLYN 6 Series User manual
MERLYN
MERLYN 8 Series User manual
MERLYN
MERLYN Arysto Ten GMW100 User manual
MERLYN
MERLYN 6 Series User manual
MERLYN
MERLYN ARYSTO User manual
MERLYN
MERLYN 6 Series User manual
MERLYN
MERLYN IQ Nexa User manual
MERLYN
MERLYN MB12 User manual
MERLYN
MERLYN NEXA VWBSVL300 User manual
MERLYN
MERLYN 6 Series User manual
MERLYN
MERLYN NEXA VWBSVL300 User manual
MERLYN
MERLYN IONIC EXPRESS User manual
MERLYN
MERLYN 8 Series User manual
MERLYN
MERLYN SIDE PANEL User manual
MERLYN
MERLYN MB7 User manual
MERLYN
MERLYN 8 Series User manual
MERLYN
MERLYN 6 Series User manual
MERLYN
MERLYN MB11 User manual
MERLYN
MERLYN ARYSTO User manual
