Maytronics Dolphin Wave 30 User manual
Dolphin Wave 30 Pool Cleaner | Operating Instructions
1
Contents
1. INTRODUCTION .............................................................................2
2. SPECIFICATIONS ............................................................................2
3. WARNINGS AND CAUTIONS........................................................2
3.1 Warnings.................................................................................2
3.2 Cautions..................................................................................2
4. POOL CLEANER PARTS..................................................................3
5. USING THE POOL CLEANER.........................................................4
5.1 Setup.......................................................................................4
5.2 Putting the Pool Cleaner into the pool................................5
5.3 Removing the Pool Cleaner from the pool..........................5
5.4 Maintenance...........................................................................6
5.5 Off-season storage ................................................................7
CADDY ASSEMBLY .............................................................................50
Robotic Pool Cleaner
Dolphin Wave 30
Operating Instructions
EN
2
Dolphin Wave 30 Pool Cleaner | Operating Instructions
Robotic Pool Cleaner Dolphin Wave 30
Operating Instructions
1. INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner.
We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and
cost effective pool cleaning. Its reliable filtration in all pool conditions and all-surface climbing brush
enhance maximum pool hygiene.
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologys, long lasting
performance and easy maintenance.
2. SPECIFICATIONS
Motor protection: IP 68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft
3. WARNINGS AND CAUTIONS
3.1 Warnings
Use the originally supplied power supply only
Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth
leakage interrupter (ELI)
Keep the power supply out of standing water
Position the power supply at least 3m/10ft away from the edge of the pool
Do not enter the pool while the pool cleaner is working
Unplug the power supply before servicing
3.2 Cautions
When not in use store the Pool Cleaner on the Caddy in a shaded area.
Use the Pool Cleaner in the following water conditions only:
Chlorine Maximum 4 ppm
pH 7.0 - 7.8
Temperature 6 – 34°C / 43-93°F
NaCl Maximum 5000 ppm
CAUTION
Digital "Switch mode" Power supply
Input 100-250 AC Volts
50-60 Hertz ; 180 Watt
Output <30 VDC ; IP 54
Dolphin Wave 30 Pool Cleaner | Operating Instructions
3
4. POOL CLEANER PARTS
Bottom lid an d fi lte r Bag
Won de r Bru sh
For smooth ceramics.
Combin e d Bru sh
All surface climbing brush
ideal for most pool surfaces
PVC Bru sh
For concrete, PVC,
fiberglass and liner.
Optional Brushes
Filtration
Robotic Pool Cleaner Model Dolphin Wave 30
Power supply unit
Brushes
4
Dolphin Wave 30 Pool Cleaner | Operating Instructions
5. USING THE POOL CLEANER
5.1 Set Up
Attach the floating cable to the power supply by inserting it with the notch on the connector (1) lined up
with the groove in the socket on the power supply and turning clockwise (2).
GFI/ELI
40°C Max
104°F Max
Dolphin Wave 30 Pool Cleaner | Operating Instructions
5
° °
° °
Turn the power supply ON.
OFF
5.2 Putting the Pool Cleaner into the pool
5.3 Removing the Pool Cleaner from the pool
The robot will perform automatic shut-off at the end
of the cleaning cycle.
Turn OFF and unplug the power supply.
CAUTION
If Wonder brush/ Wonder rings are dry,
soak them in water until soft.
Shake the robot from side to side or turn it
upside down to release trapped air.
Let it sink to the pool floor.
The Pool Cleaner will now operate until it has
reached the end of the cleaning cycle.
CAUTION
DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.
Using the floating cable, bring the Pool Cleaner to the pool’s edge.
Using the handle remove the Pool Cleaner from the pool.
B
C
C
A
ON
° °
° °
6
Dolphin Wave 30 Pool Cleaner | Operating Instructions
Clean the filter bag with a hose.
Periodically clean the brushes with a hose.
It is recommended to periodically wash
the filter bag in a washing machine.
Use gentle cycle program.
Filter bag
Dolphin Wave 30 Pool Cleaner | Operating Instructions
7
To remove the kinks,
stretch the cable out
completely and let it
sit for at least a day in
the sun.
If you notice debris trapped in the impeller open the impeller and remove the debris.
If the pool cleaner will not be in use for an extended
period, perform the following storage steps:
on the Caddy.
a protected area out of direct sun/rain/frost at a
temperature of between 5˚- 45˚C / 41˚- 113˚F .
5.5 Off-season storage
Cleaning the impeller
Unplug the power supply.
Cable
A
B
Ph Ph
No. 2
Table of contents
Other Maytronics Swimming Pool Vacuum manuals
Maytronics
Maytronics Dolphin Explorer E30 User manual
Maytronics
Maytronics 8180090 User manual
Maytronics
Maytronics Dolphin WAVE 300 XL User manual
Maytronics
Maytronics Dolphin W 20 User manual
Maytronics
Maytronics Dolphin WAVE 300 XL User manual
Maytronics
Maytronics Dolphin M400 User manual
Maytronics
Maytronics Mass 10 User manual
Maytronics
Maytronics Dolphin Nautilus CC User manual
Maytronics
Maytronics Dolphin S100 User manual
Maytronics
Maytronics Dolphin Wave 75 User manual
Maytronics
Maytronics Dolphin POOL UP User manual
Maytronics
Maytronics 2x2 Gyro User manual
Maytronics
Maytronics MBC5-UNI User manual
Maytronics
Maytronics Dolphin SX30 User manual
Maytronics
Maytronics CLASSIC 8D-UNI User manual
Maytronics
Maytronics Dolphin WAVE 100 User manual
Maytronics
Maytronics Dolphin Liberty User manual
Maytronics
Maytronics MTC8-UNI User manual
Maytronics
Maytronics DOLPHIN DX4 User manual
Maytronics
Maytronics MTC6 DELUXE 5 User manual
