Maytag MHWE201YW User manual

W10408696B

W10409178B - SP

WASHER

INSTALLATION

INSTRUCTIONS

Table of Contents

WASHER SAFETY.........................................................1

INSTALLATION REQUIREMENTS................................2

Tools and Parts................................................................2

Alternative Parts..............................................................2

Location Requirements ..................................................3

Drain System ...................................................................4

Electrical Requirements .................................................5

INSTALLATION INSTRUCTIONS..................................5

Connect Drain Hose........................................................6

Connect Inlet Hoses........................................................7

Level Washer ...................................................................8

Complete Installation Checklist.....................................9

WASHER SAFETY

INSTALLATION NOTES

Date of purchase:_________________________________

Date of installation: _______________________________

Installer: ________________________________________

Model number: ___________________________________

Serial number: ___________________________________

NOTES SUR L’INSTALLATION

Date d’achat :____________________________________

Date d’installation : _______________________________

Installateur : _____________________________________

Numéro de modèle :_______________________________

Numéro de série :_________________________________

Table des matières

SÉCURITÉ DE LA LAVEUSE ......................................10

EXIGENCES D’INSTALLATION ..................................10

Outillage et pièces ........................................................10

Autres pièces.................................................................10

Exigences d’emplacement ...........................................11

Système de vidange......................................................13

Spécications électriques............................................13

INSTRUCTIONS D’INSTALLATION............................14

Raccordement du tuyau de vidange............................15

Raccordement des tuyaux d’arrivée d’eau.................16

Établissement de l’aplomb de la laveuse....................17

Liste de vérication pour l’achèvement

de l’installation ..............................................................19

INSTRUCTIONS

D’INSTALLATION

DE LA LAVEUSE

Optional tools:

Parts supplied:

NOTE: All parts supplied for installation are in the washer

basket.

4" min

(102 mm)

Wood block

Adjustable or open end

wrenches 1⁄2" (13 mm) and

9⁄16" (14 mm)

Ruler or measuring tape

Level

Pliers that open to 19⁄16"

(39.5 mm)

Flashlight Bucket

Beaded tie strap Drain hose

INSTALLATION REQUIREMENTS

Tools and Parts

Gather required tools and parts before starting installation.

Tools needed:

Transport bolt hole

plugs (Quantity will vary,

depending on model.)

Alternative Inlet Hoses:

(may be required for some installations, not supplied

with washer)

n 8212656RP 10 ft (3.0 m) Inlet hose, Black EPDM (2 pack)

n 8212641RP 5 ft (1.5 m) Inlet hose, Black EPDM (2 pack)

n 8212546RP 4 ft (1.2 m) Inlet hose, Black EPDM (2 pack)

n 8212545RP 5 ft (1.5 m) Inlet hose, Red and Blue EPDM

(2 pack)

n 8212487RP 5 ft (1.5 m) Nylon braided inlet hose (2 pack)

n 8212638RP 6 ft (1.8 m) Nylon braided inlet hose, space

saving 90° elbow, hypro-blue steel couplings

(2 pack)

n 8212637RP 6 ft (1.8 m) Inlet hose, Black EPDM, space

saving 90° elbow, hypro-blue steel couplings

(2 pack)

Available Accessories:

An optional matching pedestal is available for your washer.

Please contact your retailer for ordering information, or see

the Assistance or Service page on the back of your Use and

Care Guide.

Alternative parts

(Not supplied with washer)

Your installation may require additional parts. To order, please

refer to toll-free numbers on the back page of your Use and

Care Guide.

If you have: You will need:

Laundry tub or Sump pump system

standpipe taller than (if not already available)

96" (2.4 m)

Overhead sewer Standard 20 gal. (76 L) 30" (762 mm)

tall drain tub or utility sink and sump

pump (available from local plumbing

suppliers)

1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)

diameter Standpipe Adapter

Part Number 3363920

Connect Kit Part Number 285835

Floor drain system Siphon Break Part Number 285834;

additional Drain Hose,

Part Number 8318155; and Connector

Kit, Part Number 285835

Drain hose too short Extension Drain Hose

Part Number 285863

Water faucets beyond 2 longer water ll hoses;

reach of ll hoses 6 ft (1.8 m) Part Number 76314

10 ft (3.0 m) Part Number 350008

Drain hose form and hose

clamp

Inlet hoses (2) with

washers (4)

Parts needed: (Not supplied with washer)

LOCATION REQUIREMENTS

Proper installation is your responsibility.

You will need:

n A water heater set to 120° F (49° C).

n A grounded electrical outlet located within 6 ft (1.8 m) of

power cord on back of washer.

n Hot and cold water faucets located within 4 ft (1.2 m) of hot

and cold water ll valves on washer, and water pressure of

20-100 psi (137.9-689.6 kPa).

n A level oor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet or surfaces with foam backing is

not recommended.

n Floor must support washer’s total weight (with water and load)

of 400 lbs (180 kgs).

IMPORTANT: Do not install, store, or operate washer where

it will be exposed to weather or in temperatures below 32° F

(0° C). Water remaining in washer after use may cause damage

in low temperatures. See “Washer Care” in Washer Use and Care

Guide for winterizing information.

All dimensions show recommended spacing allowed, except for

closet door ventilation openings which are the minimum required.

For each arrangement, consider allowing more space for ease of

installation and servicing, and spacing for companion appliances

and clearances for walls, doors, and oor moldings.

Space must be large enough to allow door to fully open.

Add spacing of 1" (25 mm) on all sides of washer to reduce

noise transfer. If a closet door or louvered door is installed, top

and bottom air openings in door are required.

Recessed area or closet installation

(stacked washer and dryer):

301/2"

(775 mm)

27"

(686 mm)

36"

(914 mm)

501/4"

(1276 mm)

(25 mm)

36" min.

(914 mm)

(50 mm)

Custom under counter installation:

Recessed area or closet installation (washer only):

48" min.

(1220 mm)

(25 mm)

(102 mm)

24 in.2

(155 cm2)

48 in.2

(310 cm2)

(76 mm)

(25 mm)

51/4"

(133 mm)

24 in.2

(155 cm2)

48 in.2

(310 cm2)

(76 mm)

72"

(1829 mm)

12"

(305 mm)

(25 mm)

(102 mm)

24" min.

(610 mm)

38" min.

(965 mm)

(25 mm)

Recessed or closet installation (washer on pedestal):

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an

Extension Drain Hose (Part Number 285863) that may be

purchased separately. See “Alternative Parts”. Minimum siphon

break height: 28" (710 mm) from bottom of washer. (Additional

hoses may be needed.)

30"

(762 mm)

28"

(710 mm)

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum

carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)

diameter to 1" (25 mm) diameter Standpipe Adapter Kit is

available (Part Number 3363920). Top of standpipe must be

at least 30" (762 mm) high; install no higher than 96" (2.4 m)

from bottom of washer. If you have an overhead sewer and

need to pump higher than 96 inches, a sump pump and

associated hardware are needed. See “Alternative Parts”.

Minimum capacity: 20 gal. (76 L). Top of laundry tub must

be at least 30" (762 mm) above oor; install no higher than

96" (2.4 m) from bottom of washer.

Floor drain system

30"

(762 mm)

41/2"

(113 mm)

41/2"

(113 mm)

30"

(762 mm)

30"

(762 mm)

DRAIN SYSTEM

Drain system can be installed using a oor drain, wall standpipe,

oor standpipe, or laundry tub. Select method you need.

IMPORTANT: To avoid siphoning, only 41/2" (113 mm) of drain

hose should be inside standpipe. Always secure drain hose with

beaded tie strap.

Floor standpipe drain system

(178 mm)

(25 mm)

(102 mm)

(229 mm)

(25 mm)

Custom cabinet installation: Wall standpipe drain system

41/2"

(113 mm)

See requirements for oor standpipe drain system.

Laundry tub drain system

INSTALLATION

INSTRUCTIONS

NOTE: To avoid oor damage, set washer onto cardboard

before moving it.

It is necessary to remove all shipping materials for proper

operation and to avoid excessive noise from washer.

Move washer to within 36" (914 mm) of its nal location. It must

be in a fully upright position.

ELECTRICAL REQUIREMENTS

n A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is recommended that a separate circuit

breaker serving only this appliance be provided.

nThis washer is equipped with a power supply cord having

a 3 prong grounding plug.

nTo minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation

of the customer to have the properly grounded outlet installed

by a qualied electrician.

nIf codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

n Do not ground to a gas pipe.

n Check with a qualied electrician if you are not sure the

washer is properly grounded.

nDo not have a fuse in the neutral or ground circuit.

Locate all transport bolts on rear of washer (quantity may vary,

depending on model).

1. Move washer

48"

(1.2 m)

2. Locate transport bolts

Loosen bolts with a 13 mm (1/2") wrench.

Slide each bolt and spacer to center of hole. Pull bolts and

plastic spacers from back of washer. Save transport bolts

and spacers. Contact a qualied servicer if washer is to be

transported.

Close bolt holes on cabinet back with transport bolt hole plugs

included with washer parts.

Pull power cord through opening in rear panel and close

holes (2) with attached white plastic cap.

NOTE: If washer is transported at a later date, call a certied

technician to properly set up washer for relocation, to avoid

suspension and structural damage.

CONNECT DRAIN HOSE

Gently place power cord over top of washer to allow free

access to back of washer.

Squeeze hose clamp tabs with pliers and slide over end of

drain hose. Slide drain hose onto washer elbow connector

and secure with clamp.

For a laundry tub or standpipe drain, go to step 8.

You may need additional parts with separate directions.

See Floor drain system under “Alternative Parts”.

3. Remove transport bolts from

washer

4. Cover bolt holes with transport

bolt hole plugs

6. Place power cord over top

5. Remove power cord

7. Attach drain hose to drain port

Run water through both faucets and inlet hoses, into a laundry

tub, drainpipe, or bucket, to get rid of particles in the water

lines.

Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

Snap either end of the drain hose form to the drain hose at the

point where the corrugation begins (A). Bend the drain hose to

form and snap into place (B).

Place hose into standpipe (shown in picture) or over side of

laundry tub.

IMPORTANT: Only 41/2" (113 mm) of drain hose should be

inside standpipe; do not force excess hose into standpipe or

lay on bottom of laundry tub. Drain hose form must be used.

CONNECT INLET HOSES

Insert new at washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

Attach hose to hot water faucet. Screw on coupling by hand

until it is seated on washer. Use pliers to tighten couplings an

additional two-thirds turn. Repeat this step with second hose

for cold water faucet.

IMPORTANT: Do not overtighten or use tape or sealants on

valve when attaching to faucets or washer. Damage can result.

HELPFUL TIP: Make note of which hose is connected to hot

water to help in attaching hoses to washer correctly. In most

standard congurations, hoses will cross over each other when

attached correctly.

Washer must be connected to water faucets with new inlet

hoses (A) with at washers (B) (not provided). Do not use old

hoses.

NOTE: Both hoses must be attached and have water owing

to inlet valves. For optimal performance, hot and cold water

must be supplied to the washer.

9. Place drain hose in standpipe

4.5"

(113 mm)

Drain

hose form

8. Connect drain hose form

A B

10. Connect washer into inlet hose

A B

11. Connect inlet hoses to water

faucets

12. Clear water lines

LEVEL WASHER

Leveling your washer properly reduces excess noise and

vibration.

NOTE: Installing washer on soft oor surfaces, such as

carpets or surfaces with foam backing, is not recommended.

Remove cardboard from beneath washer.

Slide washer to its nal location. Place a level on top edges

of washer, checking each side and front. If not level, tip

washer and adjust feet up or down as shown in steps 17

and 18, repeating as necessary. If washer is against a wall,

move out slightly before tipping back.

Grip washer from top and rock back and forth, making sure all

four feet are rmly on oor. Repeat, rocking washer from side

to side. If washer rocks, go to step 18 and adjust leveling feet.

If all four feet are in rm contact with oor, go to Step 19.

Not Level LEVEL Not Level

Attach hot water hose to hot water inlet valve marked with a

red valve. Screw coupling by hand until it is snug. Use pliers

to tighten couplings an additional two-thirds turn. Repeat with

cold water inlet valve.

IMPORTANT: To reduce risk of hose failure, replace the hoses

every 5 years. Record hose installation or replacement dates

for future reference.

nDo not overtighten or use tape or sealants on the valve.

Damage to the valves can result.

nPeriodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Slowly turn on water faucets to check for leaks. A small

amount of water may enter washer. It will drain later.

13. Connect inlet hoses to washer

14. Turn faucets on and check for leaks

15. Secure drain hose with

beaded tie strap

41/2"

(113 mm)

41/2"

(113 mm) 41/2"

(113 mm)

Laundry Tub Standpipe Wall

16. Check levelness of washer

place level here

17. Rock washer to test foot contact

Secure drain hose to laundry tub leg, drain

standpipe, or inlet hoses for wall standpipe

with beaded tie strap located in parts bag.

To avoid siphoning, do not seal or put more than

41/2" (113 mm) of the drain hose into drainpipe or standpipe.

COMPLETE INSTALLATION

CHECKLIST

qCheck electrical requirements. Be sure you have correct

electrical supply and recommended grounding method.

qCheck that all parts supplied are now installed. If there is an

extra part, go back through steps to see what was skipped.

qCheck that you have all of your tools.

qCheck that transport bolts and plastic spacer materials were

completely removed from back of washer.

qCheck that both hot and cold hoses are attached and water

faucets are on.

qCheck for leaks around faucets, valves, and inlet hoses.

qRemove protective lm, tape, or any packaging material

remaining on washer.

qCheck that washer is plugged into a grounded 3 prong

outlet.

qDispose of/recycle all packaging materials.

qRead “Using Your Washer” in your Washer Use and Care

Guide.

qTo test and clean your washer, press POWER and choose

the NORMAL cycle and run it without clothes. Use only HE

detergent. Use 1/2 the manufacturer’s recommended amount

for a medium-size load.

If washer is not level, use a 9/16" or 14 mm open-end or

adjustable wrench to turn jam nuts clockwise on feet until they

are about 1/2" (13 mm) from the washer cabinet. Then turn the

leveling foot clockwise to lower the washer or counterclockwise

to raise the washer. Recheck levelness of washer and that all

four feet are rmly in contact with the oor. Repeat as needed.

HELPFUL TIP: You may want to prop up front of washer

about 4" (102 mm) with a wood block or similar object that

will support weight of washer.

When washer is level and all four feet are rmly in contact with

the oor, use a 9/16" or 14 mm open-end or adjustable wrench

to turn jam nuts counterclockwise on leveling feet tightly

against washer cabinet.

HELPFUL TIP: You may want to prop washer again with a

wooden block.

18. Adjust leveling feet

Raise

Washer

Lower

Washer

Jam nut

19. Tighten leveling feet with jam nut

Jam nut

20. Plug into a grounded 3 prong outlet

SÉCURITÉ DE LA LAVEUSE

Pièces fournies :

REMARQUE : Toutes les pièces fournies pour l’installation

se trouvent dans le panier de la laveuse.

4" min

(102 mm)

Cale en bois

Clés plates ou clés à

molette de 1⁄2" (13 mm) et

9⁄16" (14 mm)

Règle ou mètre ruban

Niveau

Pince avec ouverture

jusqu’à 19/16" (39,5 mm)

Attache de xation perlée Tuyau de vidange

EXIGENCES D’INSTALLATION

Outillage et pièces

Rassembler les outils et piéces nécessaires avant de commancer

l’installation.

Outillage nécessaire :

Bouchons d’obturation

de trous de boulons de

transport (La quantité peut

varier, selon le modèle.)

Tuyau de vidange et bride

de tuyau

Outillage facultatif :

Lampe de poche Seau

Other manuals for MHWE201YW

This manual suits for next models

Table of contents

Languages:

Other Maytag Washer manuals

Maytag

Maytag MVWX500XL0 User manual

Maytag

Maytag MVWC200XW Assembly instructions

Maytag

Maytag W10240444A User manual

Maytag

Maytag LAT2300 User manual

Maytag

Maytag W10607442A User manual

Maytag

Maytag MVWB980BG0 User manual

Maytag

Maytag SAV-1 User manual

Maytag

Maytag W10235703A User manual

Maytag

Maytag LAT9406 User manual

Maytag

Maytag MAV-3 User manual

Maytag

Maytag MFR60PN User manual

Maytag

Maytag Bravos MVWB850Y User manual

Maytag

Maytag MXS20 Operating instructions

Maytag

Maytag MHW6630MBK User manual

Maytag

Maytag BRAVOS MVWB700VQ User manual

Maytag

Maytag Atlantis III User manual

Maytag

Maytag Performa PAV2200 User manual

Maytag

Maytag MVWC300BW1 User manual

Maytag

Maytag MAH14PDAAL Instruction Manual

Maytag

Maytag MHW8000AW0 User manual

Maytag

Maytag Neptune SL-3 User manual

Maytag

Maytag MXS20 User manual

Maytag

Maytag 3RMTW4905TW0 User manual

Maytag

Maytag LAT9520 User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide