Matan Barak Series Instruction Manual
10100139 - C © Matan Digital Printers Ltd. Page 1 of 13
Installing the Linear Encoder
(3 m and 5 m Printers)
Technical Note – 10100139 Rev. C
10100139 - C © Matan Digital Printers Ltd. Page 2 of 13
Safety Procedures
Before reading this Technical Note, please refer to the section on Safety
Procedures in the Barak User's Manual.
http://www.matanprinters.com/download.asp?p=/UV%20line/Customer%20Re
quirements/
About this Technical Note
This Technical Note describes the installation of the Linear Encoder on the 3 m
and 5 m Barak printers.
The Linear Encoder's List of Parts
The following tables show the parts required for the 3 m and 5 m Linear Encoder
Kit.
3 & 5 M Linear Encoder
Part # for 3 M Part # for 53 M Description Qty
10100139 10100139 Technical Note 1
77700424 77700424 Linear Encoder Kit 1
77700423 77700422 Encoder Scale 1
77700391 77700391 Linear Encoder Kit 1
22200864 22200864 Encoder Strip Clamps 2
33300754 33300754 Bracket for Converter 1
33300755 33300755 Connecting Plate 1
55500068 55500068 Screw M3x12: 3
55500017 55500017 Screw M4x10 4
55500176 55500176 Screw M6x16 CON 2
55500010 55500010 Spring Washer M4 4
55500089 55500089 Flat Washer M4 4
55500185 55500185 T-nut M6 2
33300762 33300762 Bracket 2
33300754 33300754 Bracket 1
22200866 22200866 Jig for sticking Scale 1
55500035 55500035 Spring Washer M3 3
You will also need Loctite #222.
The Encoder Magnetic Scale The Encoder Converter & Reader
Connecting Plate Bracket for Converter
Encoder Clamp Kit
T-nut
CON Screw
Clamp
10100139 - C © Matan Digital Printers Ltd. Page 3 of 13
Preparation
1. Check that you have a complete set of the correct components for this
installation, as detailed in the list of parts and shown in the figures above.
2. Make sure that the CARRIAGE is at the HOME position.
3. Print the scaling.mjob file from My Documents\Barak FE.
4. Turn off the printer.
5. Disconnect the X MOTOR ENCODER and the power cable, as shown below.
Installing the Linear Encoder
1. Wearing protective gloves, clean the top of the printer's BEAM and the area
next to the CARRIAGE BELT, using alcohol, as shown in the following two
figures.
Use a clean wipe and alcohol Clean the top of the printer beam
2. Manually move the CARRIAGE to the middle of the printer.
3. Hold one end of the ENCODER SCALE, with the adhesive strip facing down.
10100139 - C © Matan Digital Printers Ltd. Page 4 of 13
4. At the left side of the CARRIAGE, use Sellotape to stick the end of the ENCODER
SCALE onto the beam, as shown below.
10100139 - C © Matan Digital Printers Ltd. Page 5 of 13
One of the ends of the encoder magnetic scale stuck to the beam
5. Make sure that the SCALE roll is to your left and that its end is at the bottom
of the roll and facing to your right.
6. Move the CARRIAGE to the left, over the SCALE, until you see the right end of
the SCALE exposed at the right side of the CARRIAGE, as shown below.
The encoder magnetic scale appears to the right of the Carriage
7. Remove the Sellotape from the end of the SCALE.
Encoder Scale
Sellotape
Carriage Encoder Scale
Sellotape
8. Gently pull the right end of the SCALE to the very end of the right end of the
beam, as shown below.
End of the beam
10100139 - C © Matan Digital Printers Ltd. Page 6 of 13
Stick the end of the magnetic scale to the right side of the beam
9. Peel off the protective tape from the adhesive strip of the SCALE, as shown
above.
10. Place the JIG on the SCALE as shown below.
11. Place the MAGNETIC SCALE JIG, on the MAGNETIC SCALE as shown above.
12. Using the jig to keep it in the right position, stick the MAGNETIC SCALE along
the entire BEAM, and at the same time, remove the protective tape of the
adhesive strip, as shown below.
Peel off the
protective tape
from the Scale
Jig
Protective Strip
Encoder Scale
Sticking the magnetic scale Removing the sticky protective tape
13. You must now secure the MAGNETIC SCALE to the BEAM. This is done using the
two CLAMPS.
At the right end of the BEAM, insert the T-nut into the BEAM's groove, and
then insert the CLAMP into the same slot, above the T-nut.
14. Apply one or two drops of Loctite #222 onto the conical screw's thread and
tighten the screw, through the CLAMP, into the T-nut, as shown below.
10100139 - C © Matan Digital Printers Ltd. Page 7 of 13
Carriage Belt Con Screw M6 x 16
T-nut (under the Clamp)
Clamp
Magnetic Scale
Beam
The ri
g
ht end of the Beam
15. Secure the left end of the SCALE to the BEAM, in the same way that you
secured the right side.
Adjusting the Encoder Reader
1. Attach the ENCODER READER to the Bracket as shown below.
Positioning the Encoder Reader Securing the Encoder Reader
2. Place the ENCODER READER and the BRACKET on a flat surface so they will be
correctly aligned with each other and tighten the screws, as shown below.
Aligning the sensor and the bracket on a flat surface
3. Using two screws, washers and spring washers, attach the BRACKET to the
CARRIAGE, as shown below.
10100139 - C © Matan Digital Printers Ltd. Page 8 of 13
10100139 - C © Matan Digital Printers Ltd. Page 9 of 13
2 screws
Attaching the Bracket to the Carriage
4. Using a dry wipe, clean the magnetic scale all along its complete length, as
shown below.
Magnetic Scale
Cleaning the Magnetic Scale
5. Disconnect the old encoder connectors.
6. Reinstall the BRACKET with the ENCODER READER, onto the CARRIAGE but do
not tighten the screws yet.
7. Using the ENCODER READER's BOX BRACKETS, place the ENCODER READER's
electronic box over the right BCC card, and connect the new ENCODER
READER connectors instead of the old connectors, as shown below.
Placing the Encoder Reader's electronic box and connecting the new connectors
Attaching the Encoder Reader's electronic box to the Carriage
8. Turn on the printer.
9. Place a 0.5mm feeler gauge between the ENCODER READER and the MAGNETIC
SCALE to adjust the height, and tighten the bracket screws, as shown below,
then remove the gauge.
Adjusting the height between the encoder reader and the magnetic scale to 0.5mm
10100139 - C © Matan Digital Printers Ltd. Page 10 of 13
Table of contents
Other Matan Printer manuals
