Marsden M-150 User manual

Table of contents

Popular Scale manuals by other brands

AWS

AWS ZEO-50 user manual

Gima

Gima Glass Body Fat Analyzer Use and maintenance book

Seca

Seca 374 user manual

TEC

TEC TEC SL59 SERIES owner's manual

Axis

Axis B/E Series user manual

Alecto

Alecto ACW-40 user manual

Rice Lake

Rice Lake MSI-4260 IS Technical manual

IKA

IKA RCT basic safety control operating instructions

ADE

ADE M20011 operating manual

Duronic

Duronic KS3000 manual

Digi

Digi SM-720 Service manual

Cardinal

Cardinal CS Series Operation manual

Korona

Korona Kastella Instructions for use

A&D

A&D FC-50Ki instruction manual

BDA

BDA CAMARGUE installation guide

Tanita

Tanita HD-357 Instructions for use

Leifheit

Leifheit 03173 quick start guide

Lumme

Lumme LU-1340 user manual

OPERATING MANUAL

M-150

Please take time to read these

instructions before starting

to use the scale

Contents

Maintenance and General Care 3

Assembly Instructions 4

Operating Instructions 6

BMI Operation 7

Zero/Tare/Hold/Units 8

Error Messages 9

Contact Details 10

Page 2

Maintenance and General Care

Repairs and servicing should only be carried out by an authorised service

agent.

There are no user serviceable parts in the weighing scale itself.

The mains power adaptor fuses are not accessible.

When the adaptor is plugged into the mains supply a red LED should

illuminate to indicate that the adaptor is functioning correctly. If the LED does

not illuminate, then the scale should be checked by competent personnel.

The weight indicator contains an internal rechargeable battery pack; this

should only be replaced by authorised service agents. Under normal

operating conditions the batteries should last for several years.

We would recommend using alcohol based wipes or similar when cleaning the

scale.

Please do not use large amounts of water when cleaning the scale as this

could cause damage to the scale’s electronics. You should also refrain from

using corrosive liquids or high pressure washers.

Always disconnect the scale from the mains power supply before cleaning.

Page 3

Assembly Instructions

1) Open the packaging and check that all parts are accounted for.

2) Place the cable through the column, then fix the indicator to the pillar as

shown in the image below.

Page 4

3) Connect the cable from the indicator into the load cell cable in the base.

4) Fix the column onto the scale base using the 3 x M5 bolts, making sure not to

trap any wires.

5) Push the height rod through the hole at the base of the indicator and then

connect to the black stopper on the base of the scale. Rotate the height

measure clockwise to screw into the base.

Page 5

Operating Instructions

1) Turning the scale on and off

To turn the scale on press the ON button

firmly.

The model number and software version

will briefly show on the display. Then the

scale will display 0.0 and it is ready to

use.

To turn the scale off, press and hold the

OFF button for 3 seconds.

Page 6

2) BMI Operation

Turn the scale on and then allow the

individual to stand on the scale.

When a stable weight is showing, firmly

press the BMI button.

The display will show H 1.75. This is the

height in metres and centimetres.

The last digit should be flashing.

Press the BMI key again to move to the

digit that you need to change.

Press the PRINT key to change the

flashing digit (from 0-9).

When height has been inputted press the

TARE button to confirm. The BMI will

then display.

To exit BMI mode, press TARE or ZERO.

Normal weighing mode will then be

resumed.

Page 7

3) Zero/Tare/Hold/Units

To make the scale show 0.00, press the

ZERO button once.

If you want to remove unwanted weight,

such as a coat for example, put the coat

on the scale and press the TARE button.

When the coat is removed from the scale

a minus weight will be displayed. An

individual can then stand on the scale

and the reading will be accurate.

To get a stable weight reading press the

HOLD key.

This will capture the weight and display it

even if the individual steps off the scale.

To cancel, press the HOLD key again.

To change the unit of measurement in

standard weighing mode, press the UNIT

key for 3 seconds with nobody on the

scale.

The indicator will then change the unit

between kg and lb.

Page 8

Error Messages

Error Message

Meaning

Err1

Incorrect password has been entered

Err2

Out of setting range

Err4

Unable to zero due to the weight being

out of zero range

Page 9

Page 10