Magnetek GPD 333 User manual

MagneTek

GPD 333

Technical Manual

efesotomasyon.com - Yaskawa ac drive,servo motor

Fm-1

CONSTANT FACTORY

SETTING USER

SETTING

no-00

no-01

0000

no-02

60.0

no-03

230.0

no-04

60.0

no-05

1.5

no-06

12.0

no-07

1.5

no-08

12.0

no-09

10.0

no-10

10.0

no-11

10.0

no-12

10.0

no-13

0.0

no-14

0.0

no-15

0.0

no-16

0.0

no-17

6.0

no-18

0000

no-19

See

para. 3.8

in manual

no-20

0000

no-21

0000

no-22

1.00

no-23

0.00

no-24

100

no-25

no-26

CONSTANT FACTORY

SETTING USER

SETTING

no-27

0.0

no-28

0.0

no-29

1.0

no-30

170

no-31

160

no-32

no-33

no-34

no-35

no-36

no-37

no-38

no-39

0.0

no-40

0000

no-41

160

no-42

0.1

no-43

( = 10 kHz)

no-45

1.00

no-46

0000

no-47

no-50

0.0

no-51

1.0

Constant

no-44

currently NOT USED.

Constants

no-52

thru

no-59

currently

NOTUSED.

Effective Date: 1/24/95

Constants

no-48

and

no-49

are for

display-only functions; no user setting

possible.

MagneTek

QUICK REFERENCE – – GPD 333CONSTANTS

efesotomasyon.com - Yaskawa ac drive,servo motor

Fm-2

"Blank" backup for page Fm-1

efesotomasyon.com - Yaskawa ac drive,servo motor

WARNING

Do not touch circuit components until main input power has been

turned off and "CHARGE" lamp is extinguished. The capacitors

are still charged for up to 5 minutes and can be quite dangerous.

Do not connect or disconnect wires and connectors while power is

applied to the circuit.

CAUTION

The GPD 333 leaves the factory with constants initialized for

external 2-Wire control and constant

no–00

set to 01 . Before

using either initialization function of this constant, know your con-

trol wiring configuration :

08 = Factory 2-Wire control initialization (maintained Run contact)

09 = Factory 3-Wire control initialization (momentary Start/Stop input)

Entering either initialization code returns all constants to factory

settings, and automatically returns constant

no-00

setting to 01 .

If the GPD 333 is connected for 3-Wire control and this constant is

set to 08 (2-Wire control initialization), the motor may run in

reverse direction WITHOUT A RUN COMMAND APPLIED.

Equipment damage or personal injury may result.

Constant

no-03

must be set for the proper motor voltage. Drive

leaves factory with this constant set for 230.0 or 460.0 volts.

CAUTION

Always ground the GPD 333 using ground terminal G ( E ). See

paragraph 1.4.2 "Grounding".

Never connect main circuit output terminals T1 ( U ), T2 ( V ) &

T3 ( W ) to AC main circuit power supply.

CAUTION

Do not perform a withstanding voltage test on any part of the

GPD 333. Equipment uses semi-conductors and is vulnerable to

high voltage.

The Control PC board employs CMOS ICs which are easily dam-

aged by static electricity. Use proper electrostatic discharge

(ESD) procedures when handling the Control PC board.

– i –

efesotomasyon.com - Yaskawa ac drive,servo motor

IMPORTANT

All constants have been factory set. Do not change their set-

tings unnecessarily. Changing constant settings requires use of

the optional Digital Operator, Model DS039.

– ii –

efesotomasyon.com - Yaskawa ac drive,servo motor

– iv –

Figure 1-1. GPD 333 NEMA 1 Dimensions

NOTE: For GPD 333 NEMA 4/12 dimensions, see page 56.

RATED

INPUT HWD

H1 W1 d

MODEL

NO.

DIMENSIONS in inches (mm)

5.91 (150)

7.87 (200)

DS020, 21

DS022, 29

DS023 - 25

DS040, 41

DS042, 43

DS044, 45

4.13 (105)

5.51 (140)

7.48 (190)

3.94 (100)

5.47 (139)

6.69 (170)

4.72 (120)

6.69 (170)

7.48 (190)

5.43 (138)

7.32 (186)

7.28 (185)

3.66 (93)

5.04 (128)

4.96 (126)

6.89 (175)

0.20 (5)

0.22 (6)

.024 (7)

230V

460V

4 holes "d" diameter

(at corners of heat sink)

FRONT VIEW SIDE VIEW

efesotomasyon.com - Yaskawa ac drive,servo motor

Section 1 INSTALLATION

1.1 GENERAL. The GPD 333 is a high performance

pulse width modulated design which generates a sine-coded,

adjustable voltage/frequency three phase output for complete

speed control of any conventional squirrel cage induction

motor. The GPD 333 can maintain a 150% current overload

capability for 60 seconds. The GPD 333 will not induce any

voltage line notching distortion back to the utility line and

maintains a displacement power factor of not less than 0.98

throughout its speed range.

When properly installed, operated and maintained, the

GPD 333 will provide a lifetime of service. It is mandatory that

the person who operates or maintains this equipment thor-

oughly read and understand this manual before proceeding.

1.2 RECEIVING. The GPD 333 is thoroughly tested at

the factory. After unpacking, verify the part numbers with the

purchase order (invoice). Any damages or shortages evident

when the equipment is received must be reported immediately

to the commercial carrier who transported the equipment.

Assistance is available from your sales representative.

1.3 PHYSICAL INSTALLATION. Location of the

GPD 333 (Figure 1-1) is important to achieve proper perfor-

mance and normal operating life. The unit should be installed

in an area where it will be protected from:

• Direct sunlight, rain or moisture.

• Corrosive gases or liquids.

• Vibration, airborne dust or metallic particles.

For effective cooling as well as proper maintenance, the

GPD 333 must be installed vertically. There MUST be a

MINIMUM 4.0 inch clearance above and below, and a MINI-

MUM 1.18 inch clearance on each side.

For open type chassis, remove top cover and terminal cover.

When mounting units in an enclosure, make sure air entering

drive is below 113°F (45°C).

efesotomasyon.com - Yaskawa ac drive,servo motor

1.3.1 Installation or Removal of Digital Operator.

The GPD 333 is shipped with the

status panel (shown at right) in

place. If programming of con-

stants is to be performed, or if

local control via keypad entry is

desired, the optional Digital

Operator, Model DS039, must be

installed.

1. Ensure that input power is

not applied to the GPD 333, and

the "CHARGE" lamp is off.

2. Remove the GPD 333 access

cover (see Figure 1-2).

3. Press down on the terminal marker lever (see View B in

Figure 1-1.1), and lift upward on the bottom edge of the status

plate to remove it from the mounting recess.

4. Locate the Digital Operator in the mounting recess, as

shown in View A of Figure 1-1.1, and press until it snaps into

place.

5. Reinstall the access cover.

If, after constant programming, the drive is not to be operated

or monitored via the Digital Operator, it may be removed with-

out affecting operation. Perform the same procedure as above

to remove the Digital Operator and reinstall the status plate.

1.1

Status Plate

efesotomasyon.com - Yaskawa ac drive,servo motor

1.2

Figure 1-1.1. Installing/Removing Digital Operator

View A – Installing

View B – Removing

efesotomasyon.com - Yaskawa ac drive,servo motor

Table of contents

Other Magnetek Controllers manuals

Magnetek

Magnetek IMPULSE G+ Series 3 User manual

Magnetek

Magnetek Impulse G+ series 4 User manual

Magnetek

Magnetek IMPULSE G+ User manual

Magnetek

Magnetek HPV 600 User manual

Magnetek

Magnetek HPV 900 Series 2 User manual

Magnetek

Magnetek Impulse G+ series 4 User manual

Magnetek

Magnetek IMPULSE G+ Series 3 User manual

Magnetek

Magnetek IMPULSE G Plus Series 4 User manual

Magnetek

Magnetek FLEX EX2 Service manual

Magnetek

Magnetek RVS-DN User manual

Magnetek

Magnetek FLEX EX User manual

Magnetek

Magnetek SBN Series User manual

Magnetek

Magnetek 2001-G+M User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual