LUCCI Air LONDO DC User manual

v1.0-AU (07/2022)

LUCCI

LONDO DC

CEILING FAN

⚫INSTALLATION

⚫OPERATION

⚫MAINTENANCE

⚫WARRANTY INFORMATION

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE

INSTALLATION AND FAN OPERATION.

LONDO DC Fan Installation Instructions

1 | P a g e

THANK YOU FOR PURCHASING

Thank you for purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power

which gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement and

silent operation.

Energy saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to

65% more energy than ceiling fans with traditional AC motors.

Silent operation – This DC fan motor is programmed with a stabilised current which efficiently reduces motor

noise.

Low operating temperature – The DC power is managed effectively which brings down the motor operating

temperature to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the

longevity of the motor.

6 speed remote control - Regular AC ceiling fans usually come with only 3 speeds, this DC fan comes

complete with a 6 speed remote, which gives a greater choice of comfort levels.

SAFETY PRECAUTIONS

1. The appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

2. Children should be supervised to ensure that they do not play with the appliance.

3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring

rules.

WARNING:

FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION

MUST BE INCORPORATED INTO THE FIXED WIRING IN

ACCORDANCE WITH THE WIRING RULES.

As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum

electrical safety of this standard.

Please note warranty will be void if installation is without a means for an

all-pole disconnection incorporated in the fixed wiring in accordance with

the wiring rules.

LONDO DC Fan Installation Instructions

2 | P a g e

Example: If a fan is connected to a circuit that can be isolated via an all-

pole safety switch at the switchboard, then this is considered to be an

all-pole disconnection to the ceiling fan electrical circuit, meeting the

requirements of clause 7.12.2 of AS/NZS 60335.1.

A single-pole switch on the active of the receiver input of remote

control must also be included in the wiring, and located the same

room as the ceiling fan.

4. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.

Contact your local government for information regarding the collection systems available. If electrical

appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water

and get into the food chain, damaging your health and well-being.

5. The structure to which the fan is to be mounted must be capable of supporting a weight of 16kg.

6. The fan should be mounted so that the blades are at least 2.1 m above the floor.

7. This fan is suitable for indoor, alfresco and coastal areas where the fan is fully undercover with a minimum

of 1 wall. This fan is not waterproof. When installed in an alfresco or coastal area, the ceiling fan must be

positioned in a location protected from water, wind and dust. Exposure to these elements will void the

warranty. Mounting the fan in a situation where it is subject to water or moisture is dangerous and may

increase the risk of damage, injury or electrical shock and will void the warranty.

8. Must be assembled and installed by a licensed electrician.

9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling

fan and contact the manufacturer, its service agent or suitably qualified persons.

10. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,

its service agent or suitably qualified persons.

11. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a

sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension

system shall be performed by the manufacturer, its service agent or suitably qualified persons.

LONDO DC Fan Installation Instructions

3 | P a g e

PARTS LIST

•Unpack your ceiling fan carefully. Remove all parts and hardware.

•Lay out all the components on a smooth non-scratch surface and make sure there are no components

missing before assembling. If parts are missing, return the complete product to the place of purchase for

inspection or replacement.

•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product

which appears damaged in any way. Return the complete product to the place of purchase for inspection,

repair or replacement.

•Examine all parts, you should have the following:

Mounting bracket x1

Mounting bracket screws x4

Fan assembly x1

Spare screw for fan blade x 1

Blades x 3 pcs

Blade Support Plates x3

Bottom cover x1

Remote receiver and Remote controller, screw,

battery, holder x 1 set

Motor housing x 1

Fig. 1

LONDO DC Fan Installation Instructions

4 | P a g e

INSTALLING THE FAN

TOOLS REQUIRED:

- Phillips / flat head screwdriver

- Pair of pliers

- Adjustable spanner

- Step ladder

- Wire cutter

- Wiring, supply cable as required by local provincial and national wiring codes and regulations

INSTALLING THE MOUNTING BRACKET

•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the

blade to the nearest objects or walls.

•Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 16kg,

with 4 long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig. 2)

NOTE: The bracket screws provided are for use with wooden structures only. For structures other

than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the

mounting surface and the surrounding environment.

ANGLED CEILING INSTALLATION

The hanging system of this fan is ONLY suitable for flat ceiling installation.

DO NOT install the fan on an angled ceiling.

Fig. 2

16 KG

LONDO DC Fan Installation Instructions

5 | P a g e

HANGING THE FAN TO MOTOR ASSEMBLY

•Install the motor housing (1) onto the motor assembly. (Fig.3)

•Lift the fan assembly up to the mounting bracket. Hang the fan assembly onto the J-hook (2) of the

mounting bracket. (Fig.4)

⚫Complete the electrical wiring according to the ‘ELECTRICAL WIRING DIAGRAM’ section below.

⚫ELECTRICAL WIRING DIAGRAM THE FAN

PREPARE AND COMPLETE THE ELECTRICAL WIRING --- WIRING DIAGRAM (FIG. 5)

WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A

LICENSED ELECTRICIAN.

NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED

WIRING.

NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN

ISOLATION SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN

PROGRAMMING THE REMOTE AND RECEIVER TO PAIR TOGETHER.

Ensure the motor earth wire is connected to the single earthing terminal block “1” in the diagram below.

(Fig. 5)

Fig. 3

Fig. 4

LONDO DC Fan Installation Instructions

6 | P a g e

From mains supply to mounting bracket terminal block: (Fig. 5)

1. Connect the live supply wire to the “L” terminal of the terminal block on the mounting bracket.

2. Connect the neutral supply wire to “N” terminal of the terminal block on the mounting bracket.

3. Connect earth wire to the earth terminal of the terminal block on the mounting bracket.

From mounting bracket to receiver and motor: (Fig. 5)

4. Click together the supply wires from the mounting bracket to the input of the DC motor receiver.

5. Click together the output wires of DC motor receiver to the input wires of the fan motor via the quick

connector plugs.

6. Connect the earth wires from the fan motor to the single earthing terminal block “1” in the diagram.

Fig. 5

LONDO DC Fan Installation Instructions

7 | P a g e

INSTALL THE FAN ASSEMBLY TO THE MOUNTING BRACKET

•After completing the electrical connection at the mounting bracket terminal block, connect the ceiling fan

wiring via the quick connector plugs.

NOTE: Ensure the earth wiring is secure and correct, by performing an earthing continuity test from

the fan’s accessible metal body back to the earth terminal at the terminal block on the mounting

bracket.

Install the fan assembly to the mounting bracket (Fig.6)

•There are 4 screws pre-installed on the mounting bracket:

- Loosen two canopy screws with star washer (2) by half thread from the mounting bracket. (For L-shape

slot on canopy to be mounted).

- Loosen two canopy screws (1) and remove from the mounting bracket.

•Lift the hanging canopy of the fan assembly up to the mounting bracket and let the L-shape slot on the

hanging canopy go through the two canopy screws with star washer (2). (Fig.7)

•Turn the hanging canopy (3) until it locks in place at the end section of the L-shape slot, ensure the star

washer are between the hanging canopy (3) and screw head. Secure it by tightening the two canopy

screws with star washer (2). (Fig.7)

•Secure and tighten the canopy screws (1) to the mounting bracket. The hanging canopy (3) shall have 4

screws (1) & (2) in total. Avoid damaging the electrical wiring prepared previously when hanging the

canopy. (Fig.8)

Fig. 6

Fig. 7

Fig. 8

LONDO DC Fan Installation Instructions

8 | P a g e

•Align the arrow mark (4) on the hook surface of the motor housing (5) up to the screws (2) of hanging

canopy (3). (Fig.9)

•Finally attach the motor housing (5) to the mounting bracket, secure it by pushing the hooks of the

motor housing into the slot holes of the hanging canopy and turn it anti clockwise. (Fig.9)

INSTALLING THE FAN BLADE

BLADE ATTACHMENT (Fig.10)

1. Before installing the blades, remove the blade screws with lockwashers from the bottom of fan motor.

2. Orientate the blade Support plate and fan blade onto the fan assembly (Fig.10)

Mount the fan blade onto the fan assembly using three blade screws with lockwashers in step 1, (Fig.10).

Ensure all screws are tightened evenly to reduce the chance of warping or unbalancing.

Take care not to over tighten the screws, as this can damage the blades

Take note the correct side of the blades with the marking “THIS SIDE UP” faces the ceiling.

3. Repeat for the remaining Two fan blades and support plates.

To secure the three blade support plates and the fan blades to the fan assembly, tighten all screws with

lockwashers.

Fig. 9

LONDO DC Fan Installation Instructions

9 | P a g e

INSTALLING THE BOTTOM COVER ( Fig.11)

Secure the bottom cover to the fan by turning it clockwise.

INSTALLATION OF THE REMOTE CONTROL HOLDER (Fig. 12)

Fig. 11

1. Locate a suitable wall to fix the remote control holder with the 2 screws. (Fig.12a).

2. Slide the remote into the holder to rest the remote. (Fig. 12b)

Fig. 12a

Fig. 12b

Fig. 10

Table of contents

Other LUCCI Air Fan manuals

LUCCI Air

LUCCI Air AIRFUSION A Installation guide

LUCCI Air

LUCCI Air AIRFUSION A Owner's manual

LUCCI Air

LUCCI Air Airfusion Moto Installation guide

LUCCI Air

LUCCI Air AIRFUSION CAROLINA Installation guide

LUCCI Air

LUCCI Air CONDOR Owner's manual

LUCCI Air

LUCCI Air FIJIAN II Series User manual

LUCCI Air

LUCCI Air Aria-WS-WH User manual

LUCCI Air

LUCCI Air AIRFUSION A User manual

LUCCI Air

LUCCI Air Airfusion Louisville User manual

LUCCI Air

LUCCI Air 209047 User manual

LUCCI Air

LUCCI Air AIRFUSION CAROLINA Installation guide

LUCCI Air

LUCCI Air AIRFUSION AIRLIE II ECO Series Installation guide

LUCCI Air

LUCCI Air AIRFUSION MARINER User manual

LUCCI Air

LUCCI Air AIRFUSION UNIONE-56 ORB User manual

LUCCI Air

LUCCI Air Futura ECO Series User manual

LUCCI Air

LUCCI Air Nordic User manual

LUCCI Air

LUCCI Air AIRFUSION SLIPSTREAM User manual

LUCCI Air

LUCCI Air PUMA User manual

LUCCI Air

LUCCI Air AIRFUSION BREEZE TRIPOD FAN User manual

LUCCI Air

LUCCI Air AIRFUSION BALI LD-BALI-52 User manual

LUCCI Air

LUCCI Air OSPREY 216170 Owner's manual

LUCCI Air

LUCCI Air AIRFUSION AIRMOVER Installation guide

LUCCI Air

LUCCI Air Airfusion Atlanta User manual

LUCCI Air

LUCCI Air AIRFUSION PEREGRINE Installation guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual