Lorex SG7210S User manual
It’s all on the web BUSINESS & HOME
B&W
INDOOR/OUTDOOR
OBSERVATION SYSTEM CAMERA
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Model SG7210S
Software Upgrades
Firmware Upgrades
www.lorexcctv.com
Specifications
Image Sensor ¼” B&W CMOS Image
Sensor
Effective Pixels H: 320, V: 240
Scanning System 2:1 Interlace EIA
Scanning Frequency H: 15.75KHz, V: 60Hz
Resolution 240 TV Lines
Shutter Speed Auto 1/60 – 1/6,000 Sec
S/N Ratio N/A
Sync. System Internal
Min. Illumination 0.5 Lux F2.0
White Balance AWB
Video Output 1 Vp-p
Video Termination 6 pin Mini DIN
Lens 3.6 mm F2.0
Power Supply 12 Vdc (from Monitor)
Current Consumption 150 mA
Operating Temp 14ºF to 113ºF (-10ºC to 45ºC)
Weather Proof Rating IP 44
Gain Control AUTO
VISIT
Quick Set-u
p
Guide
Strategic Vista International Inc.
Copyright © 2005 Strategic Vista International Inc
As our products are subject to continuous improvement, SVII
and its subsidiaries reserve the right to modify product design,
specifications and prices, without notice and without incurring
any obligation. E&OE
ti
g
hten
swivel
Features:
•B&W Indoor/ Outdoor* Motion Sensor Camera
•¼” B/W CMOS Image Sensor
•Two way audio
•Compatible with all Lorex, Sylvania and Sentinel
CCTV B&W Observation Systems
•3.6 mm wide angle lens
55 ft extension cable
B&W PIR Motion Sensor
Camera Mounting Bracket
SG7210S Camera with 6’ cable and
mounting bracket
a. Attach the camera to the mounting stand and
tighten the swivel.
* This camera is not designed for direct exposure to water, rain or
snow
b. Connect the supplied cable to the back of the
camera
1. Confirm Package Contents 2. Mount and Install the Camera 3. Connect the Camera to the Monitor
a. Connect the other end of the cable to the back
of the observation system monitor.
Keep the camera installed away from sunlight.
Also avoid places where humidity is high or unable to
protect against rain. The mounting bracket must be
attached to a structural device, such as a wall or ceiling
rafter using a suitable fastener.
4. Troubleshooting
PROBLEM REMEDY
No Picture Check the connection
Picture Flickering Make sure the camera is not
facing any direct light or
sunlight
Motion Sensor is not
working. Check the connections from
the PIR to the camera
c. Locate a wall stud or ceiling joist and secure
the stand using the supplied screws.
Table of contents
Other Lorex Security Camera manuals
Lorex
Lorex E892AB Series User manual
Lorex
Lorex W461ASC Series User manual
Lorex
Lorex LNZ32P4 SERIES User manual
Lorex
Lorex VQ1032 User manual
Lorex
Lorex Professional CVC6993CL User manual
Lorex
Lorex SG7610B User manual
Lorex
Lorex SG6185W User manual
Lorex
Lorex CVC6993 User manual
Lorex
Lorex LW3400 Series User manual
Lorex
Lorex C861MB Series User manual
Lorex
Lorex E881AP Series User manual
Lorex
Lorex CVC6973HR User manual
Lorex
Lorex Vantage LBCHD2051 Series User manual
Lorex
Lorex E892AB Series User manual
Lorex
Lorex LNC201 User manual
Lorex
Lorex Vantage LDC6011PK2 User manual
Lorex
Lorex Vantage LW2231 User manual
Lorex
Lorex LW2202C User manual
Lorex
Lorex LZV1722 User manual
Lorex
Lorex LNE1001 User manual
