Lorex DCP1000 User manual

AUTO PAN TILT COLOR DOME

CAMERA FOR USE WITH VISTAPRO4

DIGITAL MONITORING SYSTEM

DCP1000

DYNACOLOR

FEATURES & FUNCTIONS

Reliable, high quality 1/4" CCD Camera providing optimum image clarity

Connects to computer via Interface box and RS232C – RS485 converter*

Remote PAN/TILT control with VistaPro4 software

Slow speed Pan/Tilt operation (15° per second) at 355° pan and 80° tilt range

3.6mm lens, 1Lux (F 2.0)

CONTENTS

This Package Contains:

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Explanation of two Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated "dangerous voltage" within the product's enclosure

may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance-(servicing) instructions in the literature

accompanying the appliance.

WARNING – TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO

RAIN OR MOISTURE.

Pan Tilt Controller

Interface Module

DCP1000 Color Auto Pan

Tilt Color Dome Camera

65 ft DIN extension

and 7 ft RS485

connection cables

*IMPORTANT NOTE:

THIS AUTO PAN TILT DOME CAMERA CANNOT FUNCTION ON VISTAPRO4 SOFTWARE

WITHOUT THE ACC-RS232 CONNECTOR ACCESSORY (SOLD SEPARATELY)

Pan Tilt Controller Interface Module

Port Description Connection Type

To Camera RS-485 data input/ video input 6 Pin DIN jack

To DVR Serial data output / video output 6 Pin DIN jack

SW 1 -6 Camera ID selection 6 Pin DIP switch

TO CAMERA

- transmits the Pan/Tilt control signals from the VistaPro 4 to the DCP1000 Dome Camera

- receives the video signal from the DCP1000 Camera to the VistaPro 4.

TO DVR

- receives the RS-485 signal from the PC’s Comm port (via the ACC-RS232 connector)

- transmits the video signal that comes from Pan/Tilt Dome Camera to DVR.

6 PIN DIP SWITCH

- sets the Channel ID of Pan/Tilt Dome Camera to correspond to the channel on the VistaPro4.

Refer to the diagram below for how to set the Dip Switch to correspond with a camera.

1 2 3 4 5 6

CAM

ID: 1

1 2 3 4 5 6

CAM ID: 2

1 2 3 4 5 6

CAM ID: 3

1 2 3 4 5 6

CAM ID: 4

①CAMERA INPUT

CONNECTOR

②DVR INPUT

CONNECTOR

③6PIN DIP

SWITCH

①②③

INSTALLATION

Ensure electrical power is not connected to the dome camera and PC system

during installation.

DIAGRAM SHOWING TYPICAL SET-UP

Important Note:

For the P/T/Z Camera Model setting in the Camera menu of Setup in the VistaPro4, the

DCP1000 is the “DYNACOLOR” camera in the drop down menu.

STEP BY STEP SETUP INSTRUCTIONS

Step 1: Mounting the Camera

Separate the back-plate from the base of the camera by gently twisting the base while

securing the back plate.

Attach the camera back plate on the ceiling using the Ø3 X 20 screws (supplied)

Secure the camera to the ceiling by gently twisting the base of the camera onto the

ceiling mounted back plate

Connect the 65’ Camera DIN cable to the female DIN input found on the Camera.

Connect the other end of the cable to the Interface box.

RS-485(+)

RS-485(-)

RS-232C

(to PC COM Port)

(VistaPro 4 Main

Board)

VIDEO

DC12V

7ft

RS485

Cable

65ft

6Pin Din

Cable

Pan/Tilt

Dome Camera

Interface

RS-232C to RS-485

CONVERTER

Do not hold clear bubble or the swivel when attaching the camera to

the back plate.

Step 2: Connecting the Camera to the VistaPro4 Digital Video Capture Card

At the location of the PC, plug the other end of the 65’ Camera DIN cable into the DIN

port labeled “To Camera” found on the PT interface module.

Using the 7’ RS-485 Connection Cable, connect the end terminated with the DIN plug to

the port labeled “To DVR” (next to the DIP switches) on the PT Interface module.

On the other end of the RS-485 Connection Cable, screw the single orange wire into the

“TX +” terminal of the ACC-RS232, and the green wire to the “TX –” terminal.

Plug the RCA jack (from the RS-485 Connection cable” into the desired Camera Input

found on the VistaPro4 card.

Connect the ACC-RS232 connector into an available DB9 Comm Port.

Step 3: Setting the Camera Address

The Dip Switch setting of the camera connected to the PT Interface must correspond to

the RCA Camera Input of the VistaPro 4

TECHNICAL SPECS: DCP1000 Pan/Tilt Dome Camera

Image sensor 1/4" Color CCD

Active pixels 512(H) X 492(V)

Image sensor area 4.8(H) X 3.7(V) mm

Resolution > 330 TV lines

Min. illumination 1 Lux (F2.0)

Video output 1.0V p-p (75 ohms)

Electronic iris 1/60 ~ 1/100,000 sec

Lens 3.6mm

Synchronization Internal

Signal format 525 lines, 2:1 interlace

System connection 6 Pin Mini DIN jack

Power source DC12V (from interface or controller)

Power consumption MAX. 2.4W

Operating temperature -10°C ~ +50°C

Dimension 126 X 107 mm

Weight 1Kg

Pan/Tilt speed 15° per second

Pan travel 355°

Tilt travel 80°

Table of contents

Other Lorex Security Camera manuals

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide