Lionel 464R Sawmill User manual
72-4147-250
7/04
Lionel
#464R Sawmill
Owner’s Manual
Car available separately
Congratulations on your purchase of the Lionel #464R Sawmill! This accessory features a
rotating “blade,” flashing warning lights, and an operating conveyor belt. When the
Sawmill is in operation, a conveyor belt carries the logs into the mill and finished lumber
emerges from the other side of the building.
Sawmill Inventory
2
Table of contents
Powering the Sawmill 3
Installing the Sawmill 4
Operating the Sawmill 5
Wiring and operating your Sawmill with TrainMaster Command Control 6-7
Adjusting the Sawmill 8-9
Replacing the lamps 10
Notes 11
Limited Warranty/Lionel Service 12
• Sawmill accessory
• Logs
• Wooden boards
• Slide switch
• Three green wires
• Owner’s Manual
• Service Center list
The following Lionel marks may be used throughout this instruction manual and are protected under law.
All rights reserved.
Lionel®, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™, DynaChuff™,
StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1®Remote Controller,
PowerMaster®, Lionel ZW®, ZW®, PowerHouse®, TMCC®, Lionelville™, Lockon®, Wireless Tether™
The name FasTrack®is used with permission from Pitsco, Inc.
Powering the Sawmill
Your Sawmill operates best at 10-14 volts (AC). As illustrated in Figure 1, you may connect the
accessory to a separate power supply or to a Lionel Lockon (available separately, 6-62900)
connected to your track. You will need the ends of the wires to be stripped back 1/4” to 3/8”.
To strip the wires, use a pair of wire strippers. Only an adult should perform this
task! Always use care when stripping wires.
1. Attach one wire to one of the spring clip terminals. Connect it to the Power/A terminal on
your power supply OR to the #1 terminal on your Lockon.
2. Attach another wire to the remaining spring clip terminal. Connect it to one of the terminals
on the small switch included with this accessory.
3. Attach another wire to the remaining switch terminal. Connect it to the Common/Ground/U
terminal on the power supply OR to the #2 terminal on the Lockon.
3
POWER
SUPPLY
COMMON/GROUND/U
POWER/A
Figure 1. Power connections
Slide switch
Spring clips
Rear view of Sawmill
Caution!
Installing the Sawmill
As illustrated in Figure 2, we recommend that you position the unloading platform on the
Sawmill directly in front of a Remote-Control Track section (available separately, 6-65530
for O gauge, 6-12746 or 6-65149 for O-27 gauge). Lionel Log Dump Cars (available separately)
can be triggered to empty their loads onto the platform using the track section’s controller.
4
You may choose to permanently secure the Sawmill to your layout with four screws (not
included). Refer to Figure 3 for the location of the mounting holes.
Figure 3. Mounting hole locations
Bottom view of sawmill
14 3⁄4"
Mounting holes
Figure 2. Remote-Control Track section
Remote-ControlTrack
section
To permanently install the Sawmill on your layout, four mounting holes are
provided as shown.
Note!
Operating the Sawmill
After your Sawmill has been assembled and connected to the power supply, you are ready to
start the action. Refer to Figure 4.
1. Drop the wooden boards into the slot in the Sawmill roof.
2. Place the logs on the unloading platform.
3. Slide the switch to activate the accessory. The logs will travel into the Sawmill via the
moving conveyor belt, and the “blade” will begin to rotate.
4. Finished boards will appear on the other side of the building.
5. Raise the Sawmill’s rear door to retrieve the logs and start again.
5
Figure 4. Sawmill operation
Raise door to remove logs
Remote-ControlTrack section
Place or unload logs here
Insert the wooden boards here
Rear view of Sawmill
Front view of Sawmill
To protect the accessory’s electronics, power to the motor will be turned off in the
event that the belt becomes jammed. The lights will be unaffected. To restore normal
operation, turn off power to the accessory for one minute, correct the jam, and then
restore power.
Note!
ACC2 ACC2
ACC1 ACC1
Power/A
Common/Ground/U
Wiring and operating your Sawmill with TrainMaster Command Control
For operation in the TrainMaster Command Control environment, you may choose to wire
your accessory with an SC-2 Switch and Accessory Controller (available separately,
6-22980) or the Accessory Switch Controller (available separately, 6-14182). Refer to these
manuals for additional information.
We recommend using 22- gauge wire.
SC-2 wiring and operation
Three wires (not included) are needed to connect your Sawmill to the SC-2 and a separate accessory
transformer. Refer to Figure 5.
1. Attach a wire to one of the Sawmill terminals and connect it to the Power/A terminal on
your power supply.
2. Attach another wire to the remaining Sawmill terminal and connect it to the accessory
toggle ON/OFF position on the SC-2.
3. Attach a final wire to the Common/Gound/U terminal on the power supply and connect it to
the COMM position on the SC-2.
Use the AUX2 button on your CAB-1 Remote Controller to toggle the Sawmill animation ON and OFF.
The lights are on when the accessory is operating.
6
Note!
Right rear corner of Sawmill
Figure 5. SC-2 connection
Wiring and operating your Sawmill with TrainMaster Command Control
(continued)
Accessory Switch Controller wiring and operation
Three wires (not included) are needed to connect your Sawmill to the Accessory Switch Controller
(ASC) and a separate accessory transformer. Refer to Figure 6.
1. Attach a wire to one of the Sawmill terminals and connect it to the Common/Gound/U
terminal on your power supply.
2. Attach another wire to the remaining Sawmill terminal and connect it to the numbered
accessory terminal on the ASC.
3. Attach a final wire to the Power/A terminal on the power supply and connect it to the COMM
position on the ASC.
Use the AUX2 button on your CAB-1 Remote Controller to toggle the Sawmill animation ON and OFF.
The lights are on when the accessory is operating.
7
Figure 6. ASC connections
Power/A Common/Ground/U
Sawmill
(bottom view)
8
L N EL
O
I
SAWMILL
Figure 7. Sawmill disassembly
Left-hand platform
Right-hand platform
Remove the screw and slide the platform
halves away from the center section.
Sawmill building
Screw
Adjusting the Sawmill
In the event that your Sawmill fails to operate correctly, follow these steps to align the belts
inside the accessory.
To protect the accessory’s electronics, power to the motor will be turned off in the
event that the belt becomes jammed. The lights will be unaffected. To restore normal
operation, turn off power to the accessory for one minute, correct the jam, and then
restore power.
1. Remove the screw at the front of the unit and slide the two halves of the platform apart.
Refer to Figure 7.
Note!
9
2. Lift away the Sawmill building, making sure that the wires are not pulled off the building.
3. Make sure that the conveyor belt is properly seated on the drive spools, as illustrated in
Figure 8.
Figure 8. Drive belt and spool locations
Conveyor belt Tabs fit into the
slots in the housing
4. Reassemble the accessory. Align the two platforms on the frame and guide the locating tabs
on the platform into the slots on the building.
Adjusting the Sawmill (continued)
Replacing the lamps
Your Sawmill is illuminated by two LEDs (light emitting diodes). The LEDs are expected to
last for the life of the unit and are not user serviceable. Only an authorized Lionel Service
Center should service this accessory, if it ever becomes necessary.
10
Table of contents
Other Lionel Toy manuals
Lionel
Lionel Lirr Passenger User manual
Lionel
Lionel 763e Hudson User manual
Lionel
Lionel Trolley User manual
Lionel
Lionel Fastrack O-36 User manual
Lionel
Lionel VISION Line User manual
Lionel
Lionel Area 51 RS-3 User manual
Lionel
Lionel Early-Era Inspection Vehicle User manual
Lionel
Lionel The Polar Express G-gauge User manual
Lionel
Lionel Jones & Laughlin Steel Slag Train User manual
Lionel
Lionel Ford Auto Dealership User manual
Lionel
Lionel 213 User manual
Lionel
Lionel 313 User manual
Lionel
Lionel Railroad Tugboat User manual
Lionel
Lionel Powered F7 B-Unit Diesel Locomotive User manual
Lionel
Lionel Superliner StationSoundsDiner User manual
Lionel
Lionel Fastrack 060 Remote Switch User manual
Lionel
Lionel WWII Airplane Pylon User manual
Lionel
Lionel Century Club II Niagara Milk User manual
Lionel
Lionel GP-20 User manual
Lionel
Lionel Dash 9 Diesel Locomotive User manual
