Linear Technology 813 Operating and maintenance instructions

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 813

HIGH VOLTAGE MICROPOWER VOLTAGE REGULATOR

LT3013

DESCRIPTION

Demonstration circuit 813 is a high voltage micro-

power voltage regulator using the LT3013 low drop-

out linear regulator, which comes in a low-profile 12-

pin DFN package. DC813 has an input voltage range

from 3V to 80V, an output voltage range between

1.24V and 60V, and is capable of delivering 250 mA

max. The DC supply current is typically only 1 uA in

shutdown. DC813 is installed with ceramic capaci-

tors, because of its ability to maintain stability with

ceramic output capacitors. Due to its high input volt-

age range, the DC813 voltage regulator is ideally

suited for automotive and industrial applications.

Design files for this circuit board are available. Call

the LTC factory.

LTC is a trademark of Linear Technology Corporation

QUICK START PROCEDURE

DC813 is easy to set up to evaluate the performance

of the LT3013. For proper measurement equipment

configuration, set up the circuit according to the dia-

gram in Figure 1.

Please follow the procedure outlined below for proper

operation.

1. Before proceeding to test, insert a shunt into

the OFF position of jumper JP1, and insert a

shunt into jumper JP2, the 3.3V option.

2. Apply 5V across Vin (to GND). Insert the

jumper JP1 shunt into the ON position. Draw

1 mA of load current. Measure Vout; it should

be 3.3V +/- 2.5% (3.21V to 3.39V).

3. Vary the input voltage from 5V to 80V and the

load current from no load to 250 mA. Vout

should measure 3.3V +/- 5% (3.13V to

3.47V).

Note: Be aware of the power dissipated by the

LT3013, due to its high input voltage capabil-

ity. Consequently, take care to stay under the

maximum junction temperature, 125 deg.C,

when operating the LT3013.

4. Insert the jumper JP1 shunt into the OFF posi-

tion and move the shunt in jumper JP2 into

the 5V output voltage option, and repeat the

test. Re-insert jumper JP1 shunt into the ON

position. Just as in the 3.3 Vout test, the 5V

output voltage should read Vout +/- 2.5% tol-

erance under static line and load conditions,

and +/- 5% tolerance under dynamic line and

load conditions.

5. When finished evaluating, insert jumper JP1

shunt into the OFF position.

Warning - If long leads are used to power the demo circuit, the input voltage at the part could “ring”. This ring-

ing could affect the operation of the circuit or even exceed the maximum voltage rating of the IC. To eliminate

this, insert a small aluminum electrolytic capacitor (for instance, a Sanyo cap., part # 100CV10BS) on the pads

between the input power and return terminals on the bottom of the demo board. The (greater) ESR of the alu-

minum electrolytic capacitor will dampen the (possible) ringing voltage due to the use of long input leads. On a

normal, typical PCB, with short traces, the capacitor is not needed.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 813

HIGH VOLTAGE MICROPOWER VOLTAGE REGULATOR

Figure 2. Measuring Input or Output Voltage Ripple

Figure1. Proper Measurement Equipment Setup

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 813

HIGH VOLTAGE MICROPOWER VOLTAGE REGULATOR

Other Linear Technology Controllers manuals

Linear Technology

Linear Technology DC116 Series Quick setup guide

Linear Technology

Linear Technology DC1669A Quick setup guide

Linear Technology

Linear Technology LT3692A Quick setup guide

Linear Technology

Linear Technology 1215 User manual

Linear Technology

Linear Technology Analog Devices LTC3882-1 User manual

Linear Technology

Linear Technology LTM4649EY Quick setup guide

Linear Technology

Linear Technology DC1588A Quick setup guide

Linear Technology

Linear Technology DC2087A Quick setup guide

Linear Technology

Linear Technology LTC3210 User manual

Linear Technology

Linear Technology LT3755 User manual

Linear Technology

Linear Technology LTC3624 Quick setup guide

Linear Technology

Linear Technology Analog Devices LT8607B User manual

Linear Technology

Linear Technology DC2069A Quick setup guide

Linear Technology

Linear Technology LTM4620A Quick setup guide

Linear Technology

Linear Technology DC1936A Quick setup guide

Linear Technology

Linear Technology DC 1090A User manual

Linear Technology

Linear Technology LTC3212 User manual

Linear Technology

Linear Technology LTC4412 Quick setup guide

Linear Technology

Linear Technology LTC4260 User manual

Linear Technology

Linear Technology DC1855A Quick setup guide

Linear Technology

Linear Technology LT3507 Quick setup guide

Linear Technology

Linear Technology LT3480 User manual

Linear Technology

Linear Technology Analog Devices LT8708-1 User manual

Linear Technology

Linear Technology LTC1624 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual