Lifetime 2129 Quick start guide

WARNING

To ensure your safety, do not

attempt to assemble the table

without reading and following

all instructions and warnings

carefully.

VISIT THE LIFETIME WEB SITE:

WWW.LIFETIME.COM

6-PERSON ROUND

PICNIC TABLE

MODEL #2129

ASSEMBLY INSTRUCTIONS AND OWNER’S

MANUAL

Save this instruction in the event that the manufacturer

has to be contacted for replacement parts.

INSTRUCTION #1017715 11/03/2006

Copy

1. Adjustable Wrench

2. 5/16” Wrench

3. Phillips Screwdriver

BEFORE BEGINNING ASSEMBLY

A. Identify and inventory all parts using the checklist boxes on the Parts List.

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE.

• Proper and complete assembly and use is essential for proper operation and to reduce the risk of injury.

• 2 people are required for assembly.

• If technical assistance is required, contact the manufacturer.

• Most injuries are caused by misuse and/or failure to follow instructions.

TWO ADULTS ARE NECESSARY TO

COMPLETE ASSEMBLY!!

If two or more people are

sitting at the table at the

same time, we recommend

they sit across the table from

each other to prevent pos-

sible tipping of the table.

ID Part # Description Qty

AA 1007361 Table Top (1003645) 1

AB 1007365 Bench (1003635) 3

AC ZP97506 Table Leg 3

AD ZP97606 Center Table Leg Brace 3

AE ZP97706 Bench Leg 3

AF ZP97806 Bench Frame 3

AG ZP97906 Bench Leg Pivot 3

AH 1007362 Footcap 6

AI 1008729 Plug, Umbrella Hole 1

AJ 1007363 Bench Leg Cap 6

AK 1019483 Support Brace 1 3

AL 1019484 Support Brace 2 3

Table Frame Hardware (1020883)

RA BS03300 1/4” x 1/2” Screw 6

RC 1004700 5mm Cap Nut 12

RD 1004641 5mm Flat Washer 3

RE 1008307 #8 x 1/2” Screw 21

Bench Frame Hardware (1020884)

RA BS03300 1/4” x 1/2” Screw 18

RE 1008307 #8 x 1/2” Screw 12

BA 1016552 5mm x 12.5mm Carriage Bolt 24

BB 1003781 M5 Centerlock Nut 24

BD 1013012 Cotter Key 3

PARTS LIST

Tools and Materials Required

For Assembly

(Not Included)

1Footcaps on Table Legs

Turn a Table Leg (AC) upside down. Place a Footcap (AH) on

the bottom of each leg. Secure the each Footcap with two (2) #8

x 1/2” Screws (RE). Repeat for remaining two legs.

2Assemble Legs

Turn Table Legs right side up. Attach one (1) Center Leg Brace

(AD) to each table leg as shown. Ensure the end of brace angles

upwards. Secure with two (2) #8 x 1/2” Screws (RE). Repeat for

remaining Legs.

Completely tighten both Screws, then loosen them one (1) full

Stand Table Legs assemblies in circle with braces pointing in

towards the center.

Hardware Bag:

1020883

Screwdriver

RE (12)

Hardware Bag:

1020883

Screwdriver

RE (9)

Step 1 Hardware

Step 2 Hardware

Note: Completely tighten both

Screws (RE), then loosen them one

(1) full turn.

Move Clockwise and stand between the next pair of legs. Line up the end hole on the right brace with

the middle hole on the left brace as shown. Secure with one (1) #8x 1/2” Pan Head Screw (RE).

Move Clockwise and stand between the last pair legs. Line up the end hole on the right brace with the

middle hole on the left brace as shown. Secure with ine (1) #8 x 1/2” Pan Head Screw (RE). Set aside

assembly.

Note: The Center Leg Braces are joined together always in a Right over Left format.

Note: Do not completely tighten the

Screws (RE) yet.

Note: Do not completely tighten the

Screws (RE) yet.

Note: Do not completely tighten the

Screws (RE) yet.

While standing between two legs, line up the end hole on the right brace with the middle hole on the

left brace as shown. Secure with one (1) #8 x 1/2” Pan Head Screw (RE).

Two sets of three (3) Support Braces (AK & AL) come with your picnic

table. Set AK comes with two bolts next to each other (one of the bolts is

gold colored). Set AL comes with two bolts about 12” from each other.

3Support Braces to Table Top

Underside of Table

Pilot Hole

Gold Colored Bolt

Hardware Bag:

1020883

Screwdriver

Step 3 Hardware

RA (1)

Note: Do not completely tighten the Screw (RA) yet.

Place a Support Brace (AK) onto the underside of the Table Top and lightly secure the Brace with one

1/4” x 1/2” Screw (RA).

Pilot Hole

Underside of Table

Hardware Bag:

1020883

Screwdriver

Step 3 Hardware

RA (2)

Note: Do not completely tighten

the Screw (RA) yet.

Note: Do not completely tighten the Screw (RA) yet.

Place a Support Brace (AL) over Support Brace (AK) and lightly

secure the Brace to the Table Top with one (1) 1/4” x 1/2” Screw

(RA).

Pilot Hole

AK RA

Pilot Hole

Underside of Table

Hardware Bag:

1020883

Screwdriver

Step 3 Hardware

RA (2)

Note: Do not completely tighten the Screw (RA) yet.

Underside of Table

Secure Support Braces AL to AK using three (3) 5mm Washers and three (3) 5mm Cap Nuts.

WARNING

Do not overtighten the Cap Nut. If the end of

the Bolt breaks through the plastic cap, call our

Customer Service Department at the number

on Page One. Exposed threads on the end of

the Bolt may cause serious injuries.

CAUTION

Do not overtighten Screws (RA).

Overtightening may damage

parts and void warranty.

Pilot Hole

Underside of Table

Hardware Bag:

1020883

Screwdriver

Adjsutable Wrench

Step 3 Hardware

RC (3) RD (3)

RA (1)

Completely tighten all Screws (RA).

Remove the rst 1/4” x 1/2” Screw (RA) and gently tilt the Support

Brace (AK) and slide the last Support Brace (AL) into place.

Replace the rst 1/4” x 1/2” Screw (RA) into the rst Support Brace (AK).

Finally, secure the last Support Brace (AL) to the Table Top.

Completely tighten all Cap Nuts (RE).

With the Table Top facing top down on the ground, align the Leg

assembly (Step 2) over the three sets of bolts on the Support

Brace assembly. Fasten the Leg assembly to the Support Braces using

nine (9) 5mm Cap Nuts (AC). Tighten all hardware (including the Center

Braces from Step 2). Stand the Table upright.

Legs to Support Braces

Note the set of three bolts.

Hardware Bag:

1020883

Adjustable Wrench

RC (9)

Step 4 Hardware

5Assemble Benches

(Repeat This Step for all 3 Benches)

5a Turn a Bench Leg (AE) upside-down and fasten a Bench

Leg Cap (AJ) on each end of the foot. Secure each Cap

to the legs with two (2) #8 x 1/2” Screws (RE).

WARNING

Do not overtighten the Cap Nut. If the end

of the Bolt breaks through the plastic cap,

call our Customer Service Department at

the number on Page One. Exposed threads

on the end of the Bolt may cause serious

injuries.

Hardware Bags:

1020884

Screwdriver

Step 5 Hardware

RE (12)

5c Line up a bench leg with the right side of the Bench Frame (AF). Secure to frame with four (4) 5mm x

12.5mm Carriage Bolts (BA) and four (4) M5 Centerlock Nuts (BB).

5b Lay a Bench Frame (AF) top-side down, with curved

edges pointing away from you.

Note: The tab on the frame

must line up with the hole in

the Bench Leg plate.

Bench Leg

Frame

5d Line up a Bench Leg Pivot (AG) piece with the left side of the

bench seat frame. Secure to frame with four (4) 5mm x 12.5mm

Carriage Bolts (BA) and four (4) Centerlock Nuts (BB).

Note: The tab on the frame

must line up with the hole in

the Bench Pivot plate.

Bench Leg

Frame

Hardware Bags:

1020884

Screwdriver

Adjustable Wrench

BB (24) RA (18)

Step 5 Hardware

BA (24)

Table of contents

Other Lifetime Indoor Furnishing manuals

Lifetime

Lifetime 0130 User manual

Lifetime

Lifetime 60054 User manual

Lifetime

Lifetime 7060 User manual

Lifetime

Lifetime 6' PICNIC TABLE User manual

Lifetime

Lifetime 60055 User manual

Lifetime

Lifetime ADIRONDACK 60335 User manual

Lifetime

Lifetime 80421 User manual

Lifetime

Lifetime 81037 User manual

Lifetime

Lifetime 2127 User manual

Lifetime

Lifetime 60284 User manual

Lifetime

Lifetime 60064 User manual

Lifetime

Lifetime 60186 User manual

Lifetime

Lifetime 0114 Quick start guide

Lifetime

Lifetime ADIRONDACK CHAIR 60204 User manual

Lifetime

Lifetime 60064 User manual

Lifetime

Lifetime 60205 User manual

Lifetime

Lifetime RETRO PATIO 60193 User manual

Lifetime

Lifetime 60064 User manual

Lifetime

Lifetime 853281 User manual

Lifetime

Lifetime 60170 User manual

Lifetime

Lifetime 0111 User manual

Lifetime

Lifetime 0150 User manual

Lifetime

Lifetime WILD CHILD BACK PANEL 7526 User manual

Lifetime

Lifetime 80123 User manual

Popular Indoor Furnishing manuals by other brands

Homelegance

Homelegance California 1662PEK-1CK Assembly instruction

Osmond Ergonomics

Osmond Ergonomics FLO instructions

OVE

OVE ELOISE 42 installation manual

overstock

overstock MF286255 Assembly instructions

Sonoma

Sonoma 160-801 Assembly instructions

BOLERO

BOLERO Wicker Side Chair CF158 Care Instructions

Coaster

Coaster 4799N Assembly instructions

Stor-It-All

Stor-It-All WS39MP Assembly/installation instructions

Lexicon

Lexicon 194840161868 Assembly instruction

Next AMELIA NEW 462947 Assembly instructions

Furinno

Furinno 18089 Assembly instruction

Munchkin

Munchkin Push to Close MK0001 manual

impekk

impekk Manual II Assembly And Instructions

Elements

Elements Ember Nightstand CEB700NSE Assembly instructions

JWA

JWA CARY 68429 Assembly instruction

VIPACK

VIPACK AMORI AMKB9014 Assembly instructions

Anthro

Anthro GT03 Series Assembly instructions

Rowico

Rowico SANNA Assembly instructions