LevelOne FNC-0107TX User manual
FNC-0107TX
10/100Mbps Fast Ethernet
Adapter
User’s Manual
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
2
FCC Warning
This equipment has been tested and found to
comply with the regulations for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with this
user’s guide, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to cause
harmful interference, in which case the user will
be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class B product. In a domestic
environment, this product may cause radio
interference, in which case the user may be
required to take adequate measures.
Trademarks
All product and brand names are trademarks
and/or registered trademarks of their repective
companies.
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
3
Table of Contents
INTRODUCTION…………………... 4
About Fast Ethernet……………………… 4
About Auto-negotiation………………….. 4
About WOL (Wake-On-Lan)……………. 5
Product Features…………………………. 6
INSTALLATION…………………… 7
Hardware Installation…………………….. 7
BIOS Confiuration……………………….. 8
Driver Installation………………………… 8
Boot ROM Installation…………………… 8
TROUBLESHOOTING……………... 9
SPECIFICATIONS………………….10
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
4
INTRODUCTION
Thank you for choosing the Level One
FNC-0107TX 10/100Mbps Fast Ethernet
Adapter, the value leader among Fast
Ethernet adapters for PCI−Bus personal
computers. This Introduction chapter
will be useful if you are new to Fast
Ethernet and other new technology
featured by the 10/100Mbps Fast Ethernet
Adapter. Otherwise, skip ahead to the
Installation chapter.
About Fast Ethernet
Fast Ethernet is a network technology specified
by IEEE Standard 802.3u. It extends the
traditional 10Mbps Ethernet technology to
achieve 100Mbps transmission and reception,
while retaining the same CSMA/CD Ethernet
protocol. Thus while Fast Ethernet provides a
tenfold increase in network capacity, it is wholly
compatible with traditional 10Mbps Ethernet
network facilities.
AboutAuto-negotiation
Auto-negotiation is an IEEE 802.3 procedure of
negotiating the highest data flow capability
between the device (in this case, our Adapter)
and their links partner (some other device). The
data flow information, to be negotiated, consists
of the data speed (10Mbps or 100Mbps) and data
transfer (half-duplex or full-duplex
communication). The physical process of
auto-negotiation requires only a few milliseconds
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
5
to choose the fastest communications capability
between the two devices.
About WOL (for WOL model only)
WOL (Wake-On-LAN) is an ACPI function
allowing a powered OFF computer to be
powered ON from a remote station. ACPI
(Advanced Configuration Power Interface) is a
new technology and an open industry
specification to provide power management
support systems through hardware and operating
system cooperation. To use the WOL feature,
the NIC must be WOL capable and the
motherboard of the PC (for which the card is
installed) must be of ACPI architecture.
While the powered OFF computer sleeps, the
WOL NIC monitors LAN traffic for valid
Wake-up frames. The NIC will determine
whether a received Wake-up frame is addressed
to the PC. If so, the NIC will send a signal to
the motherboard to power ON the computer.
What is the utility in the WOL card?
•”I forgot a document and I'mout of town?”
Send a Wake-up signal to your computer
and transfer the needed file to your location.
•Initiate long routines and reports before you
get to work.
•Transfer files when the network traffic is
low (during late hours).
•Power ON your PC before you arrive to
work.
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
6
WOL has great utility in power management of
PCs, workstations, and kiosks.
Product Featues
Designed for versatility and performance, the
FNC-0107TX 10/100Mbps Fast Ethernet
Adapter provides the following features:
•Wake-On-LAN (WOL) provides great utility
for power management of PC.
•Operates in a PCI Bus Master slot of a
Pentium/ Pentium-Pro/ Pentium-II computer,
independent of CPU speed.
•PCI Bus Master memory access, for high
throughput and low CPU demand.
•Plug and Play installation.
•100Mbps Fast Ethernet or 10Mbps Ethernet
data transfer, selected via auto-negotiation.
•Full-duplex or half-duplex operation,
selected by auto-negotiation.
•Built-in FIFO buffers reduce overhead of
memory transfers.
•Drivers for all leading Network Operating
Systems.
•Two LED indicators: Link, Activity.
•LINK Indicator
A steady green LED indicates good
linkage between the FNC-0107TX
10/100Mbps Fast Ethernet Adapter and its
supporting hub.
•ACTIVITY Indicator
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
7
A flashing green LED indicates that the
adapter is sending or receiving data.
INSTALLATION
Installation of a FNC-0107TX 10/100Mbps Fast
Ethernet Adapter requires Hardware installation
first, then BIOS and Software installation.
Hardware Installation
1. Trun OFF the computer, unplug its power
cord and open the computer case.
2. Insert the contact edge of the FCN-0107TX
10/100Mbps Fast Ethernet Adapter into the
connector of any available PCI Bus Master
expansion slot. Press the card firmly into
the connector and ascertain that the card
contacts are fully seated in the connector.
3. For WOL model, connect the WOL cable to
the NIC WOL connector. Both ends of the
WOL cable are identical, so either and may
be used.
4. Install the bracket screw, which secures the
card to the cinouter chassis.
5. Replace the computer’s case and connect
the network cable to newly installed
network card. Reconnect the computer’s
power cord and plug it into the power
outlet.
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
8
BIOS Configuration
Due to a fault in some Plug-n-Play BIOS
programs, it happens occasionally that a newly
installed adapter is assigned an Interrupt Number
which is already assigned to another device. In
such a case, the conflict of Interrupt Number will
cause faults in the behavior of both devices.
Then it is necessary to run the CMOS Setup
utility, and manually assign a non-conflicting
Interrupt Number.
Driver Installation
Before you connect the FNC-0107TX
10/100Mbps Fast Ethernet Adapter to the
network, you have to install the network driver
first. The driver for each networking operating
system is under a separate directory. A
HELP8139.EXE file under root directory lists
the information and detailed installation
procedure of all the available drivers.
Boot ROM Installation
The optional Boot ROM device allows you to
connect a diskless workstation to the network.
Perform the following steps to install your Boot
ROM device:
1. Insert the Boot ROM into the socket on the
Card.
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
9
2. Refer to the installation procedure provided
by networking operating system.
TROUBLESHOOTING
If you experience any problems with the adapter,
first verify that the appropriate driver is loaded,
that the proper grade of cable is employed for the
network connection, and that the supporting hub
is functioning properly.
1. Ascertain that the adapter card is fully and
firmly seated in the slot connector.
2. Check the length and rating of connecting
cables.
3. Ascertain that the adapter's PCI slot is not
deactivated at the BIOS level. The CMOS
Setup utility in PCI computers ordinarily
provides the option to activate or deactivate
PCI slots.
4. Replace the adapter in question with a
verified adapter and run RSET8139.EXE
diagnostic tests on the sofrware diskette at
directory of \DIAG\.
5. Install the questioned adapter in another PCI
computer and run the tests again.
Remove all other PCI adapters from the
computer and run the tests again. If the
verification/diagnostic run is not normal, then
there is probably an interrupt number conflict
which will have to be resolved manually by a
CMOS Setup utility run after you have
reinstalled all of the expansion cards.
FNC-0107TX 10/100Mbps Fast Ethernet Adapter
10
SPECIFICATIONS
Standards: IEEE 802.3 10BASE-T
IEEE802.3u 100BASE-TX
PCI Local Bus specification
Rev.2.1
Host interface: PCI 2.1 Bus (Bus Master)
Data Bus Width: 32-bit PCI bus mastering
Jumperless Hardware
Auto-negotiation functionality
Wake-On-Lan:
(for WOL model only) Magic Packet
Microsoft wake-up frame
LED indicators: Link, Activity
Media Interface: RJ-45
EMI Compatiblity:
FCC Class B
CE Certification, Class B
VCCI-II
Canada C-Tick
Dimensions: 120mm x 58mm
Storage
Temperture: -25°C ~ 70°C
Operating Temp.: 0°C ~ 50°C
Storage Humidity: 10% ~ 90% non-condensing
Operating Humidity: 10% ~70% non-condensing
Power Consumption: 1.1 Watts (maximum)
PCB Layer: 2 layers
Other manuals for FNC-0107TX
1
Table of contents
Other LevelOne Adapter manuals
LevelOne
LevelOne PIS-3100 User manual
LevelOne
LevelOne WNC-0305USB User manual
LevelOne
LevelOne PLI-1010 User manual
LevelOne
LevelOne WUA-0605 User manual
LevelOne
LevelOne USB-0301 User manual
LevelOne
LevelOne WNC-0600USB User manual
LevelOne
LevelOne WUA-0315 User manual
LevelOne
LevelOne LevelOne WUA-0604 User manual
LevelOne
LevelOne MIMO WPC-0500 User manual
LevelOne
LevelOne WUA-0605 User manual
LevelOne
LevelOne PLI-4052 User manual
LevelOne
LevelOne WUA-0614 User manual
LevelOne
LevelOne WPC-0600 User manual
LevelOne
LevelOne USB-0502 User manual
LevelOne
LevelOne Original instructions User manual
LevelOne
LevelOne USB-0501 User manual
LevelOne
LevelOne PLI-2040 User manual
LevelOne
LevelOne PIS-3100 User manual
LevelOne
LevelOne WUA-0614 User manual
LevelOne
LevelOne PLI-3410 User manual
