Lenze S921 User manual
CANopen Communication Module
S94CAN01A
L
S921
Doc ID: S94CAN01A
Table of Contents
1 Preface and General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 How to use these Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1 Persons responsible for safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.2 General safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.1 Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.2 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 CANopen DS301 Communication Profile Support . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 Supported NMT (Network Management) services: . . . . . . . . . . . . . . . . . . . . 7
4.2 The Heartbeat Error Control Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.3 Communication Objects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. Drive 94 Specific Objects and functionality . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1 CAN Velocity mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2 CAN Torque mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.3 E94 Drive specific objects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1
ENGLISH
Preface & General Info
1 Preface and General Information
1.1 How to use these Operating Instructions
• These Operating Instructions are intended for safety-relevant operation on and with the
E94ZACAN1 CANopen option module. They contain safety information which must be
observed.
• All personnel working on and with the module must have these Operating Instructions
available and observe the information and notes relevant for them.
• These instructions are only valid in combination with the Operating Instructions of the
corresponding controller. They must always be complete and in a perfectly readable
state.
2
ENGLISH
Safety Info
2 Safety Information
2.1 Persons responsible for safety
Operator
• An operator is any natural or legal person who uses the drive system or on behalf of
whom the drive system is used.
• The operator or his safety personnel is obliged to ensure
- the compliance with all relevant regulations, instructions, and legislation.
- that only skilled personnel works on and with the drive system.
- that the personnel have the Operating Instructions available for all corresponding
works.
- that all unqualified personnel are prohibited from working on and with the drive
system.
Qualified personnel
Qualified personnel are persons who - because of their education, experience, instructions,
and knowledge about corresponding standards and regulations, rules for the prevention of
accidents, and operating conditions - are authorized by the person responsible for the safety
of the plant to perform the required actions and who are able to recognize potential hazards.
(Definition for qualified personnel to VDE 105 or IEC 364)
2.2 General safety information
• These safety notes do claim to be complete. In case of questions and problems please
contact your Lenze representative.
• At the time of delivery the drive system meets the state of the art and ensures basically
safe operation.
• The indications given in these Operating Instructions refer to the stated hardware and
software versions of the controller.
• The controller is hazardous if:
- unqualified personnel work on and with the controller.
- the controller is used inappropriately.
• Ensure by appropriate measures that neither personal injury nor damage to property
may occur in the event of failure of the drive system.
• The drive system must only be operated when no faults occur.
• Retrofitting, modifications, or redesigns are basically prohibited. Lenze must be
contacted in all cases.
3
ENGLISH 3
ENGLISH
Technical Data
3 Technical data
3.1 Related documents
• CANopen Application Layer and Communication Profile or CiA Draft Standard 301
• Drive 94 reference manual
3.2 General information
The internationally standardized CAN bus protocol, which had been developed for the
European Automobile Industry, is mainly characterized by
• Its resistance against interference and extreme temperatures
• Short transfer times
• Low connection expenses
These advantages have made CAN products interesting for other industries too.
The CANopen communication profile is based on CAN technology.
The CANopen protocol has been developed by the CiA(CON in Automation) in conformity
with the CAL (CON Application Layer). All mandatory parts of the CiA DS301 protocol,
version 4.01 have been implemented in the E94ZACAN1 Module.
3.3 Installation
The E94ZCAN1 CANopen Communication Module is designed to operate with the E94S
SimpleServo drive. For proper installation……
• Remove power from the drive and allow unit to discharge
• Remove blank module cover from Option Bay 1
• Plug in the 20 pin connector into drive
• Plug in the CANopen module
• Use set screws to connect module to drive
4
ENGLISH 4
ENGLISH
Technical Data
3.4 Configuration
Drive 94 supports CANopen communication protocol through its CANopen Communication
Module. Upon power up, the drives firmware detects the CAN Module and automatically
enables both the CANopen functionality as well as the CANopen configuration menu.
We can utilize SimpleServo LED display and push buttons to both configure the drive for the
CAN network, as well as check and set drive parameters. The “UP” (▲) and “DOWN” (▼)
buttons are used to navigate through the drives parameters.
Power up the drive and review the display.
rvn_ Drive is Enabled and in Run mode. Disable the drive by deactivating the Enable
input.
DiS_ Drive is Disabled and ready to be configured. Press the “ENTER” button
( ) to continue.
StAt Current drive status. From here you use the “UP” (▲) and “DOWN” (▼) buttons to
navigate through the drives parameters. Press the “DOWN” (▼) button to continue.
CAnd CAN delay menu. This is the delay in seconds after which a “start remote node”
message can be broadcast and its value is between 0 and 5 (seconds). Press
the “ENTER” button ( ) to view this number and use the “UP” (▲) and “DOWN”
(▼) buttons to change the delay setting. Set the delay back to “0” and press the
“ENTER” button ( ) to exit. Press the “DOWN” (▼) button to continue.
CAn0 CAN operational mode. This is where you define what mode you want the drive to
be in at power up. This parameter is R/W. To view the setting, press the “ENTER”
button ( ). Use the “UP” (▲) and “DOWN” (▼) buttons to change the setting.
Select setting “1” and press the “ENTER” button ( ) to store your setting and to
exit. Press the “DOWN” (▼) button to continue
___0 CAN starts in pre-operational state.
___1 CAN starts in operational mode.
___2 CAN starts in operational mode and is a “quasi master”, meaning that it
will send “start remote node” message (described in standard DS301)
after a delay specified in CAnd menu.
CAnS CAN network status value. This is a binary representation of the status of the
CAN network. This is read only parameter and you can have more than one
status active at one time. Press the “ENTER” button ( ) to view status. Press the
“ENTER” button ( ) to exit. Press the “DOWN” (▼) button to continue.
___1 Initialization Complete.
___2 CAN bit or frame error occurred.
___4 CAN “error passive” occurred.
___8 Receive queue overrun occurred.
__16 Transmit queue overrun occurred.
__32 Reserved
__64 Reserved
_128 CAN “bus off” error occurred
5
ENGLISH 5
ENGLISH
Technical Data
CAnA CAN network address. This parameter is R/W and can be between 0 and 127. This
is the drives address on the CAN Network. Press the “ENTER” button ( ) to view
address setting. Use the “UP” (▲) and “DOWN” (▼) buttons to change the setting.
Press the “ENTER” button ( ) to store your setting and to exit. Press the “DOWN”
(▼) button to continue.
CAnb CAN network baud rate. This is R/W parameter. Use the “UP” (▲) and “DOWN”
(▼) buttons to change the setting. Select setting “500” and press the “ENTER”
button ( ) to store your setting and to exit. Press the “DOWN” (▼) button to
continue.
1000 1000Kb baud rate
_800 800Kb baud rate
_500 500Kb baud rate
_250 250Kb baud rate
_125 125Kb baud rate
__50 50Kb baud rate
__20 20Kb baud rate
__10 10Kb baud rate
Hx.xx Drive Hardware Revision (ex. H1.01). Read only press the “DOWN” (▼) button to
continue.
Fx.xx Drive Firmware Revision (Version F1.12 or greater required for CANOPEN
Network). Read only. Press the “DOWN” (▼) button to continue.
OPEr Drive Operating Mode. This is a R/W parameter. Use the “UP” (▲) and “DOWN”
(▼) buttons to change the setting. Select either CAnV (CANBUS Velocity Mode)
or CAnt (CANBUS Torque Mode). Press the “ENTER” button ( ) to store your
setting and to exit. Press the “DOWN” (▼) button to continue.
POS_ Position Mode
uEL_ Velocity Mode
torq Torque Mode
CAnu CANBUS Velocity Mode
CAnt CANBUS Torque Mode
t-uL Velocity Limited Torque Mode.
bAud E94 Drive Baud Rate. This Baud Rate is only for RS232/RS485 communications.
It doesn’t affect the CANBUS Network. This is R/W parameter. Use the “UP” (▲)
and “DOWN” (▼) buttons to change the setting. Select setting “38.4” and press the
“ENTER” button ( ) to store your setting and to exit. Press the “DOWN” (▼) button
to continue.
_38.4 8400 bits per second
_19.2 19200 bits per second
__9.6 9600 bits per second
6
ENGLISH 6
ENGLISH
Technical Data
Adr_ E94 Drive address. This address is only for RS232/RS485 communications. It
doesn’t affect the CANBUS Network. This parameter is R/W and can be between 0
and 31. Press the “ENTER” button ( ) to view address setting. Use the “UP” (▲)
and “DOWN” (▼) buttons to change the setting. Press the “ENTER” button ( ) to
store your setting and to exit. Press the “DOWN” (▼) button to continue.
FLtS E94 Drive Fault History. This parameter is Read only. Press the “ENTER” button (
) to view. Use the “UP” (▲) and “DOWN” (▼) buttons to scroll through the fault
history. Press the “ENTER” button ( ) to exit. Press the “DOWN” (▼) button to
continue.
Ht__ E94 Drive Heatsink Temperature. This parameter is Read only and shows heatsink
temperature in °C if greater than 40°C. Otherwise the display show “LO” (low).
Press the “ENTER” button ( ) to view. Press the “ENTER” button ( ) again to
exit. Press the “DOWN” (▼) button to continue.
EnC_ E94 Drive Encoder Activity. This parameter is Read only and shows primary
encoder counts for encoder diagnostics activity. Press the “ENTER” button ( ) to
view. Press the “ENTER” button ( ) again to exit. Press the “DOWN” (▼) button
to continue.
HALL E94 Drive Hall Activity. This parameter is Read only and displays the motors Hall
sensor state. Press the “ENTER” button ( ) to view. Press the “ENTER” button (
) again to exit. Press the “DOWN” (▼) button to continue.
bUS_ E94 Drive DC Bus Voltage. This parameter is Read only and displays the DC bus
voltage value. Press the “ENTER” button ( ) to view. Press the “ENTER” button (
) again to exit. Press the “DOWN” (▼) button to continue.
CUrr E94 Drive Phase Current. This parameter is Read only and displays the current
value of the motors phase current (RMS) while the drive is enabled. If the drive is
disabled the display will show “diS”. Press the “ENTER” button ( ) to view. Press
the “ENTER” button ( ) again to exit. Press the “DOWN” (▼) button to continue.
7
ENGLISH
Communication Objects
4 CANopen DS301 Communication Profile Support
4.1 Supported NMT (Network Management) services:
The E94 Drive automatically goes to an Operational state upon reset without waiting for the
Start Node command from the NMT master.
• Start Node – Upon receiving this service request from the NMT master the drive will
resume operation. This only is applicable when the drive is in the Stopped state. The
drive resumes its move and its CANopen SDO and PDO services are operational again.
• Stop Node – Upon receiving this service request the drive stops its motion and holds its
position. (Note: power is still applied to the motor) The drive also disables its CANopen
SDO and PDO services.
• Reset Node – Upon receiving this service request the drive will reset. If the drive is in
motion it executes a quick stop before it resets.
• Reset Communication – Resets the CAN communication driver.
4.2 The Heartbeat Error Control Service
The E94 Drive can be set up as a heartbeat producer. In this mode the drive will periodically
send out a heartbeat requests. The heartbeat producer time is stored in index 0x1017 in the
object dictionary as a multiple of 1 millisecond.
Value of 0 for the heartbeat producer time disables the heartbeat service.
8
ENGLISH
Communication Objects
4.3 Communication Objects
OBJECT NAME DESCRIPTION
1000h Device Type The E94 Drive is not DSP 402 compliant but follows some
of the major velocity and torque profiles recommendations.
Therefore it uses custom device profile value of
0x00022192.
1001h Error Register The following values are allowed:
0 – NO error
1 – over voltage
2 – feedback error
3 – over current
4 – over temperature
5 – external fault detection
6 – over speed
7 – position error excess
8 – bad motor data
1008h Manufacturer Device Name Drive 94 uses the ‘SS94’ device name
1009h Manufacturer Hardware Version It is 0x94xx where xx is the current version number
100Ah Manufacturer Software Version It is 0x94xx where xx is the current version number
1017h Producer Heartbeat Time See 1.2 above
1018h Identity Object Vendor ID – 0x00456765
Product Code - 0x0000005E
1400h 1st receive PDO Parameter
(Torque)
Asynchronous PDO with 255 transmission type used only
if the drive is in CAN Torque mode. The target torque
update is triggered immediately upon receiving of this
RPDO.
Sub index 01 contains the RPDO COB-ID and has R/W
access. The default value of this COB-ID is 0x200 + CAN
network node id/address.
1401h 2nd receive PDO Parameter
(Velocity)
Asynchronous PDO with 255 transmission type and used
only if the drive is in CAN Velocity mode. The target
velocity update is triggered immediately upon receiving of
this RPDO.
Sub index 01 contains the RPDO COB-ID and has R/W
access. The default value of this COB-ID is 0x300 + CAN
network node id/address.
1600h 1st receive PDO Mapping (Torque) Only the following static mapping is supported:
Sub index 01 -> 6040h Control word
Sub index 02 -> 6071h Target Torque
NOTE: This object is used only in CAN Torque mode
1601h 2nd receive PDO Mapping (Velocity) Only the following static mapping is supported:
Sub index 01 -> 6040h Control word
Sub index 02 -> 60FFh Target Velocity
NOTE: This object is used only in CAN Velocity mode
Table of contents
Other Lenze Control Unit manuals
Lenze
Lenze i500 Series User manual
Lenze
Lenze ECS series User manual
Lenze
Lenze EtherCAT E84AYCET User manual
Lenze
Lenze EMB934 Series User manual
Lenze
Lenze ECS series User manual
Lenze
Lenze E94AYCCA Use and care manual
Lenze
Lenze EMF2192IB User manual
Lenze
Lenze ETC Series User manual
Lenze
Lenze E94AYAE-SM301 User manual
Lenze
Lenze E82ZAFSC010 User manual
Lenze
Lenze E94AYCDN User manual
Lenze
Lenze E82ZAFVC010 Use and care manual
Lenze
Lenze EtherNet/IP E84AYCEO User manual
Lenze
Lenze 8250 Series User manual
Lenze
Lenze E84DZEW Series User manual
Lenze
Lenze E84DZEVBLANP User manual
Lenze
Lenze SM302 User manual
Lenze
Lenze E84AYCEC User manual
Lenze
Lenze EMZ9374IB User manual
Lenze
Lenze EtherCAT E84AYCET Use and care manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
