Lantech IGS-0016 User manual

Lantech

IGS-0016

16 10/100/1000T Industrial Unmanaged

Ethernet Switch

IES-0016

16 10/100TX Industrial Unmanaged

Ethernet Switch

User Manual

V1.0

Sep-2019

Recommendation for Shielded network cables

STP cables have additional shielding material that is used to reduce external interference. The

shield also reduces the emission at any point in the path of the cable. Our recommendation is

to deploy an STP network cable in demanding electrical environments. Examples of

demanding indoor environments are where the network cable is located in parallel with

electrical mains supply cables or where large inductive loads such as motors or contactors are

in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the

power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

Content

Overview............................................................1

Introduction............................................................. 1

Model Lists ............................................................. 1

Packing List............................................................ 2

Safety Precaution ................................................... 2

Hardware Description.........................................3

Front Panel............................................................. 3

Top View ................................................................ 3

Dimensions............................................................. 4

Wiring the Power Inputs.......................................... 5

Wiring the Fault Alarm Contact ............................... 5

LED Indicators........................................................ 7

RJ-45 Pin Assignments........................................... 8

Cabling................................................................. 10

Mounting Installation........................................11

DIN-Rail Mounting ................................................ 11

Wall-Mount Plate Mounting................................... 13

Hardware Installation .......................................14

Installation Steps .................................................. 15

Troubleshooting ...............................................16

Overview

Introduction

The unmanaged industrial switch is a cost-effective solution and meets

the high reliability requirements demanded by industrial applications.

Model Lists

Model name

10/100/1000T

ports

10/100TX

ports

PoE ports

IGS-0016

IES-0016

For latest product specifications, please refer to Lantech official site.

Packing List

1 x 16-port Industrial Ethernet Switch

1 x Terminal Block

Safety Precaution

Attention

If DC voltage is supplied by an external circuit, please use a

protection device on the power supply input.

Hardware Description

In this paragraph, we will introduce the Industrial switch’s dimensions,

port, cabling information, and wiring installation.

Front Panel

The Front Panel of the IGS-0016/ IES-0016 are shown as below.

Front Panel of the Industrial Switch

Top View

The top panel of the Industrial Switch is equipped one terminal block

connector of two DC power inputs.

Top panel of the Industrial Switch Converter

Dimensions

. The dimensions of IGS-0016/IES-0016 are 49 x 152 x 105 mm (W x H

x D). The figure below gives the dimensions and views of each side of

the 16-port Industrial Ethernet Switch.

Wiring the Power Inputs

Please follow the steps below to insert the power wire.

1. Insert the positive and negative wires into the V+ and V- contacts on the

terminal block connector.

2. To tighten the wire-clamp screws for preventing the DC wires to loose.

Wiring the Fault Alarm Contact

The fault alarm contact is in the middle of terminal block connector as the

picture shows below. Inserting the wires, it will detect the fault status

which the power is failure or port link failure (for managed model) and form

an open circuit.

Note

The wire gauge for the terminal block should be in the range

between 12~ 24 AWG.

Insert the wires into the fault alarm contact (No. 3 & 4)

This manual suits for next models

Table of contents

Other Lantech Switch manuals

Lantech

Lantech LES-2400-RPS User manual

Lantech

Lantech LPGS-2424C Series User manual

Lantech

Lantech IES-2008 User manual

Lantech

Lantech IPES-0008A-12V User manual

Lantech

Lantech IPWMR-3204DF User manual

Lantech

Lantech LGS-2300-RPS User manual

Lantech

Lantech TPGS-L6208XT User manual

Lantech

Lantech IPES-5222T Series User manual

Lantech

Lantech IES-22812F-2P User manual

Lantech

Lantech IES-3416DSFP User manual

Lantech

Lantech IES-5408T User manual

Lantech

Lantech IPES-5208T-X Series User manual

Lantech

Lantech LPES-2208CA User manual

Lantech

Lantech LGS-2404 User manual

Lantech

Lantech mini Switch 800 User manual

Lantech

Lantech IPES-5408T-X-IGN Series User manual

Lantech

Lantech IGS-2404 User manual

Lantech

Lantech IES-0208CA User manual

Lantech

Lantech IPES-0208 Series User manual

Lantech

Lantech IES-3208C User manual

Lantech

Lantech LPES-2224C User manual

Lantech

Lantech TPGS-L6216XT User manual

Lantech

Lantech IPES-5408T User manual

Lantech

Lantech IPES-0204DFT-4 User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual