La Crosse Technology WT-3143AX1 Dimensions
La Crosse Technology, Ltd Page 1
WT-3143AX1 FAQS
The links below will work in most PDF viewers and link to the topic area by clicking
the link. We recommend Adobe Reader version 10 or greater available at:
http://get.adobe.com/reader
CONTENTS
WT-3143Ax1 FAQS............................................................................................................. 1
Batteries............................................................................................................................... 1
Atomic Clock Factory Restart............................................................................................ 2
Supported Time Zones....................................................................................................... 2
Time is Incorrect................................................................................................................. 3
Clock is incorrect by Hours but minutes are correct..................................................... 3
Manually Set Time.............................................................................................................. 3
How long will the battery last?......................................................................................... 3
Can I shut off the WWVB signal?..................................................................................... 3
Is there a booster antenna to receive the WWVB signal in a difficult location? ...... 3
Daylight Saving Time......................................................................................................... 4
Can I wire a control timing circuit to the La Crosse Technology®atomic clock?..... 4
Why do the hands spin once or twice everyday?.......................................................... 4
Hands spin non-stop .......................................................................................................... 4
Hands jumps or jerks around the dial............................................................................. 4
Hands stuck at certain time.............................................................................................. 4
Position the Clock ............................................................................................................... 5
BATTERIES
La Crosse Technology, Ltd Page 2
Explanation: Many problems are resolved with fresh batteries of the appropriate
voltage. Many items sent in under warranty work, when tested with fresh batteries.
Batteries manufactured this year will have an expiration date 10 years (or more) in
the future. Battery technology has improved and batteries will maintain voltage
longer in storage. However, the environment the batteries reside in for the 10 years
can deplete the power.
We suggest a name-brand Alkaline battery.
A minimum voltage of 1.48V is necessary for proper performance.
Use a battery dated at least six years in advance of the current year. Batteries
dated earlier than six years from now may still work, but may be unstable in
performance.
Good name-brand batteries make less noise, which reduces the chance of RF
(radio frequency) interference from the battery compartment.
Extra Battery compartments:
You can insert two additional AA batteries in the side compartments to increase
battery life up to 3 years.
Batteries should all be about the same level of charge when inserted.
ATOMIC CLOCK FACTORY RESTART
Explanation: The factory restart returns the atomic clock to an “out-of-the-box”
state and often resolves an issue.
Factory Restart:
1. Remove the battery from the clock for 15 minutes.
2. Press the Set button at least 20 times to clear all memory.
3. Slide the switch to select a time zone.
4. Insert 1 fresh AA, LR6 1.5 volt ALKALINE battery according to the polarity
marked on the case.
5. Position the clock on an exterior wall that faces Ft. Collins Colorado. During the
night, your clock will automatically set itself.
Note: The hands will move to the 12:00 position and search for the radio signal.
If the clock does not receive the radio signal in the first 10 minutes, the clock
will start running from the 12:00 position and will continue to run. Do
not attempt to reset the hands manually even though the time on the clock is
incorrect. The clock is synchronizing to the WWVB signal and once the radio
signal is decoded, the hands will automatically adjust to the correct time. This
may take up to 5 nights.
SUPPORTED TIME ZONES
This atomic clock offers four time zones: Pacific, Mountain, Central and Eastern.
La Crosse Technology®does not make an analog clock with more than four time
zones.
The atomic clock works in North America.
Outside of North America, the atomic clock will not receive a WWVB signal, but
will keep time as a quartz clock if manually set.
La Crosse Technology, Ltd Page 3
TIME IS INCORRECT
Indicative of non-receipt of WWVB signal
Electrical storms between you and Colorado can interfere with the WWVB signal
Replace battery and perform restart procedure. Allow up to 5 days to receive a
signal.
Reposition the atomic clock with the front or back facing Colorado.
Try a different location, ideally near a window. The clock should be at least six
feet from computers, TVs, air conditioners, other atomic clocks and other
electrical appliances that cause interference.
Large buildings, metal roofed buildings and buildings or rooms full of electrical
and/or radio equipment make it difficult to receive the WWVB time signal.
CLOCK IS INCORRECT BY HOURS BUT MINUTES ARE CORRECT
This is a Time Zone issue. Hold your Time Zone button for 5 seconds. The clock
should correct itself.
Check that DST is on. Press and release the small, unmarked gray button
between the ET and CT button one time.
MANUALLY SET TIME
Note: Allow up to five nights for the clock to receive the WWVB signal before
manually setting the time.
Set the clock manually:
1. Hold the SET button for 3+ seconds to activate the manual mode. Once the
clock is in manual mode, there are two ways to move the minute hand forward.
2. Hold the SET button down to move the minute hand forward consistently.
3. Alternatively, press and release the SET button rapidly (more than once per
second) to move the minute hand forward step by step (in minute increments).
4. Use these features to move the minute hand forward until the correct time is
set. The clock will automatically leave manual mode after the SET button is not
pressed for 6+ seconds.
HOW LONG WILL THE BATTERY LAST?
A good AA Alkaline battery will last over 12 months.
With 2 additional batteries, battery life is up to 3 years.
CAN I SHUT OFF THE WWVB SIGNAL?
No. If you manually set the time, when the clock receives a WWVB signal, that
signal will override the manual set.
IS THERE A BOOSTER ANTENNA TO RECEIVE THE WWVB SIGNAL IN A
DIFFICULT LOCATION?
No, the clock cannot work with a booster antenna.
La Crosse Technology, Ltd Page 4
Opening the clock or movement voids the warranty.
DAYLIGHT SAVING TIME
Dependent on your location, the position of the clock in your home, and
atmospheric interference, it may take up to 5 nights for the change from
Daylight Savings Time to Standard Time and vice-versa to occur.
Check that the DST selector bar is in the ON position.
Check for fresh batteries. Without proper batteries, the antenna will have a
harder time picking up the signal.
Position the atomic clock in a window (with the front or back) facing Ft. Collins,
Colorado and leave for up to five nights. If you do not have a window facing this
direction, position the clock near an outside wall and point the unit in this
general direction.
CAN I WIRE A CONTROL TIMING CIRCUIT TO THE LA CROSSE
TECHNOLOGY®ATOMIC CLOCK?
No, the clock cannot work on a timing circuit.
Opening the clock voids the warranty.
WHY DO THE HANDS SPIN ONCE OR TWICE EVERYDAY?
When the hands spin about the same time every day the clock is auto-correcting
the time. The hour hand should not spin more than twice around the clock.
Hands may spin if the battery is underpowered or over powered.
Use only Alkaline batteries in the clock.
HANDS SPIN NON-STOP
This is indicative of a low or overpowered battery (number 1 warranty issue).
Replace battery and perform restart procedure. Allow 5 days to catch the WWVB
signal
If constant spinning continues, the movement may need replacement.
HANDS JUMPS OR JERKS AROUND THE DIAL
This is indicative of a low or overpowered battery (number 1 warranty issue).
Replace battery and perform the restart procedure. Allow up to 5 days to receive
a signal.
If the hands continue to jump, the movement may need replacement.
HANDS STUCK AT CERTAIN TIME
This is indicative of a low or overpowered battery (number 1 warranty issue).
Replace battery and perform restart procedure. Allow up to 5 days to receive a
signal.
La Crosse Technology, Ltd Page 5
Check to see if the hands may be bent.
Movement may need replacement.
POSITION THE CLOCK
This La Crosse Technology®atomic clock is designed for indoor or outdoor use.
INDOOR: Select a location to place the radio-controlled clock where it will be at
least six feet away from a TV, computer, air conditioner or other household
electrical appliances. The optimal location is near a window. Windows facing
Colorado provide the best signal.
Table of contents
Other La Crosse Technology Clock manuals
La Crosse Technology
La Crosse Technology WT-3144S User manual
La Crosse Technology
La Crosse Technology WT-8002UV2 Dimensions
La Crosse Technology
La Crosse Technology 404-50447 User manual
La Crosse Technology
La Crosse Technology WT-3132 User manual
La Crosse Technology
La Crosse Technology 433-3833 User manual
La Crosse Technology
La Crosse Technology 012721 User manual
La Crosse Technology
La Crosse Technology BBB87733 Operating and maintenance manual
La Crosse Technology
La Crosse Technology 513-1429BL Dimensions
La Crosse Technology
La Crosse Technology WT-3161WHx1 User manual
La Crosse Technology
La Crosse Technology 403-3246BR User manual
La Crosse Technology
La Crosse Technology WT-3161BK User manual
La Crosse Technology
La Crosse Technology WS-7038U User manual
La Crosse Technology
La Crosse Technology C86286 Dimensions
La Crosse Technology
La Crosse Technology WT-3161BL User manual
La Crosse Technology
La Crosse Technology WT-3129B User manual
La Crosse Technology
La Crosse Technology WT-8112U User manual
La Crosse Technology
La Crosse Technology WS6158-IT User manual
La Crosse Technology
La Crosse Technology WS-8008U Installation guide
La Crosse Technology
La Crosse Technology 513-1311OT User manual
La Crosse Technology
La Crosse Technology KWS-8140U-IT User manual
Popular Clock manuals by other brands
Silicon Laboratories
Silicon Laboratories SI5324 manual
Heathkit
Heathkit GC-1005 Assembly manual
Oregon Scientific
Oregon Scientific PRYSMA RMR221P manual
Andrew O'Malley
Andrew O'Malley DOTKLOK Assembly instructions
ALGE-Timing
ALGE-Timing ASC3 manual
Bodet
Bodet Profil 960 Installation and operating instructions
