KT&C KEZ-c2TR28V12XIR User guide

KEZ-c2TR28V12XIR

HD-TVI 1080p Varifocal IP66 Super Beam

IR True WDR Turret Cameras with OSD,

CVBS Output and UTC Control

Quick Operation Guide

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

Thank you for selecting this KT&C Omni EZHD Series product. For

additional information please refer to the complete User Guide for

this cameras series. End users should contact their KT&C Certified

Dealer for service. Certified Dealers can obtain support directly from

KT&C.

About This Guide

While KT&C makes every effort to insure the completeness and

accuracy of the information contained in this Guide, we are not

responsible for typographical errors or misprints. At the same time,

KT&C reserves the right to make changes to improve the performance

of our products at any time without notice, and so the specifications

and content of this document are subject to change without notice.

Every effort will be made to include updates in new versions of this

manual and/or online.

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and found to

comply with the limits for a digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

the user will be required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied

accessories too are marked with "CE" and comply

therefore with the applicable harmonized European

standards listed under the Low Voltage Directive 2006/95/EC, the

EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with

this symbol cannot be disposed of as unsorted

municipal waste in the European Union. For proper

recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more information

see: www.recyclethis.info.

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed of as

unsorted municipal waste in the European Union.

See the product documentation for specific battery

information. The battery is marked with this symbol,

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

which may include lettering to indicate cadmium (Cd), lead (Pb), or

mercury (Hg). For proper recycling, return the battery to your supplier

or to a designated collection point. For more information see:

www.recyclethis.info

Safety Instructions

These instructions are intended to ensure that the camera is installed

in a manner that avoids danger to persons or property loss.

These precautionary measures are divided into “Warnings” and

“Cautions”

Warnings: Serious injury or death may occur if any of the warnings

are neglected.

Cautions: Injury or equipment/property damage may occur if any of

the cautions are neglected.

Warnings

Warnings Follow these

safeguards to prevent

serious injury or death.

Cautions Follow these

precautions to prevent

potential injury or material

damage.

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

●In the use of the product, you must be in strict compliance with

the electrical safety regulations of the nation and region. Please

refer to technical specifications for detailed information.

●Input voltage should meet the requirements for both the SELV

(Safety Extra Low Voltage) and Limited Power Source for 12 VDC

according to the IEC60950-1 standard. Please refer to technical

specifications for detailed information.

●If connecting several devices to one power supply, to avoid any

overload that may cause over-heating or a fire hazard insure that

the power supply is adequate for the power load.

●Please make sure that all plugs are firmly connected to the

power sockets. When the product is mounted on wall or ceiling,

the device shall be firmly attached, taking into consideration any

wind, snow loading, or other factors. The mounting surface shall

be capable of supporting several times the base weight of the

camera.

●If smoke, unusual odors or noise come from the device, turn off

the power at once and unplug the power cable, and then

contact authorized service personnel.

Cautions

●Make sure the power supply voltage is correct before using the

camera.

●Do not drop the camera or subject it to physical shock.

●Do not touch lenses or sensor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and wipe gently.

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

If the camera will not be used for an extended period, please

protect the lens openings from damage and/or debris.

●Avoid aiming the camera at the sun or extremely bright light

sources. Blooming or smearing may occur in excessive light

(which is not a malfunction), and could compromise the

performance of the sensor.

●The sensor may be damaged if exposed to laser energy, so when

any laser equipment is in use, make sure that the sensor will not

be exposed to the laser beam.

●Do not place the camera in extremely hot or cold (see camera

specifications) locations. Do not exceed the rated environmental

(indoor) conditions. Do not expose the camera to high levels of

electromagnetic (RF) radiation.

●To avoid heat accumulation, good ventilation is required in the

operating environment.

●Keep the camera away from solvents while in use; exposure to

liquids should not exceed IP66 environmental conditions.

●During shipping, the camera shall be packed in its original

packing, or packing providing the equivalent protection.

●Improper use or replacement of any batteries (if so equipped)

may result in the hazard of explosion. Replace with the same or

equivalent type only. Dispose of used batteries according to the

instructions provided by the battery manufacturer.

If the product does not function properly, Dealers please contact

KT&C; End Users please contact your KT&C Certified Dealer or an

authorized service center. Do not disassemble the camera for repair

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

or maintenance by yourself. (KT&C shall not assume any responsibility

for problems caused by unauthorized repair or maintenance.)

Table of Contents

1 Appearance and Description .......................................................... 7

2 Installation...................................................................................... 8

3 Camera Connection & Focus......................................................... 12

4 OSD Menu Operation ................................................................... 14

1Appearance and Description

Figure 1-1 Varifocal Turret Camera Overview

Note: True WDR processing and downscaling from 1080p to CVBS

both demand significant processor resources. CVBS output and digital

zoom are disabled when True WDR is active; where full time CVBS

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

output is desired, Digital WDR is an OSD menu option. WDR status is

easily controlled by connecting together (or disconnecting) the bare

ends of the ‘switch cable’ (if WDR was ON, connecting the wires will

turn it OFF; if WDR was OFF, connecting the wires will turn it ON).

To employ a CVBS test monitor connected to the black CVBS BNC

connector, if True WDR is on, connect the wires; when ready to put

the camera in service, disconnect the wires. If True WDR was not

active (and CVBS output is enabled), if desired after the CVBS output

is no longer required, connecting the wires will turn True WDR ON.

2Installation

Before you start:

Make sure the camera is in good condition and all the accessory

parts are included.

Make sure all related equipment is powered-off during the

installation.

Check to insure that the specifications of the camera are correct

for the installation environment.

Make sure the power supply voltage is 12VDC to avoid damage to

the camera. OBSERVE POLARITY!

If the product does not function properly, Dealers please contact

KT&C; End Users please contact your KT&C Certified Dealer or an

authorized service center. Do not disassemble the camera for

repair or maintenance by yourself.

Make sure that the mounting surface is strong enough to withstand

three times the weight of the camera.

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

If the IR LED in this camera will be active, you must observe the

following precautions to prevent IR reflection:

●Dust or grease on the lens/dome cover will cause IR reflection.

Please do not remove the cover protective film until the

installation is finished. If there is dust or grease on the

lens/dome cover, clean the lens/dome cover with clean soft

cloth and isopropyl alcohol.

●Make sure that there is no reflective surface too close to the

camera lens. The IR light from the camera may reflect back into

the lens causing haze, distortion or improper scene exposure.

Steps:

1. Attach the drill template on the wall or ceiling.

Figure 2-1 Attach the template

2. Separate the camera from the mounting base (see Figure 2-2).

Secure the base to the wall or ceiling with the supplied screws

and expansion anchors (if required).

KEZ-c2TR28V12XIR HD-TVI WDR VF XIR Turret Camera·Quick Operation Guide

Figure 2-2 Separate the Camera from the Mounting Base

3. Connect the power and video wires.

Place the camera onto the mounting

base and secure with the

enclosure/outer housing.

Figure 2-3 Place camera body and enclosure into base

Figure 2-4 3-axis Adjustment

Table of contents

Other KT&C Security Camera manuals

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications