Konica Minolta PK-517 User manual

E-1

INSTALLATION MANUAL

A10E-9550-01

PK-517 Punch Kit

I. Accessory parts

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly different

in shape from yours. In that case, instead of the

illustrations, use the appearance of your machine to

follow the installation procedure. This does not

cause any significant change or problem with the

procedure.

II. Installation procedures

Note:

When mounting the punch kit, mount it before

mounting the finisher to the machine.

1. Turn off the machine and unplug the power cord

from the power outlet.

2. Remove the protective tape.

3. If the finisher is mounted on the machine, remove

the finisher.

Note:

For the finisher removal procedure, see installa-

tion manual for finisher.

4. Remove the exit tray from the finisher.

No. Name Shape Q’ty

1. Punch unit

2. Punch box

3. Label

4. Installation

manual

set

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

A10EIXC001DA

A10EIXC002DA

4512IXC053DA

4980IXC019DA

A10EIXC003DA

A10EIXC004DA

5. Remove the upper cover from the finisher (four

screws).

6. Remove the plate from the finisher as shown in

the illustration (two screws).

7. Remove the plate from the finisher as shown in

the illustration (three screws).

8. Open the cover of the finisher as shown in the

illustration and place the punch kit on the finisher.

9. Connect the punch kit connector to the finisher.

A10EIXC005DB

A10EIXC006DA

A10EIXC007DA

A10EIXC008DA

A10EIXC009DA

Applied Machine: FS-527

A10E-9550-01E.fm 1 ページ２００９年７月２日　木曜日　午後６時２３分

E-2

10. Slightly raise the punch kit and insert the plate

removed in step 7 between the finisher and the

punch kit.

Note:

Align the three dowels on the finisher with the

three dowel holes on the plate.

11. Secure the plate to the finisher with the three

screws removed in step 7.

12. Align the middle mark on the punch kit with the

dowel on the plate and secure the punch kit (two

screws).

Note:

Use the screws removed in step 6.

13. Attach the upper cover removed in step 5 to the

finisher (four screws).

14. Attach the exit tray removed in step 4 to the fin-

isher.

15. Install the furnished punch box.

16. Affix the furnished label to the front door of the

finisher as shown in the illustration.

17. Mount the finisher to the machine.

Note:

For the finisher mounting procedures, see installa-

tion manual for finisher.

A10EIXC010DB

Dowel

A10EIXC011DA

A10EIXC012DA

A10EIXC013DA

A10EIXC014DA

III. Punch option setting

1. Plug the power cord into the power outlet and

turn on the machine.

2. Display the Service Mode screen. (For details of

how to display the Service Mode screen, see the

service manual.)

3. Touch “Finisher.”

4. Touch “Punch option setting.”

5. Touch “PK-517” and select a desired number of

holes.

6. Touch “decision.”

7. Touch “END.”

8. Touch “Exit” on the Service Mode screen.

IV. Punch hole deviance adjustment

1. Make a copy in the punch mode.

(Refer to the user’s guide (copy operations))

2. Fold the copy into halves and check for possible

deviation in the punch hole positions.

Specifications: 0 ± 2.0 mm

* If the positional deviation of the punch holes is

not within the accepted range, take the following

steps.

3. Open the upper cover of the finisher.

4. Loosen the two screws that hold the punch unit in

place.

5. Move the punch unit back and forth to adjust its

position, referring to the guide lines.

6. After the adjustment, tighten the two screws loos-

ened in step 4.

7. Close the upper cover of the finisher.

8. Make a copy and check the punch hole positions

again.

A10EIXC018DA

A10EIXC019DA

A10EIXC015DA

Screw

A10EIXC016DA

A10E-9550-01E.fm 2 ページ２００９年７月２日　木曜日　午後６時２３分

E-3

V. Punch hole position adjustment

1. Make a copy in the punch mode.

(Refer to the user’s guide (copy operations))

2. Measure width A on the copy and check to see if

the measured dimension falls within the specified

range.

Specifications: 9.5 ± 1.0 mm

<Europe: 4 holes>

Specifications: 11 ± 1.0 mm

<Sweden: 4 holes>

Specifications: 10.5 ± 1.0 mm

• If the measured width A outside the specified

range, perform the following procedure to punch

hole position adjustment.

3. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

4. Touch “Finisher.”

5. Touch “FS-FN adjustment.”

6. Touch “Punch Horizontal Position.”

7. Set the correction value using the /

keys.

• To make width A wider, enter a positive value.

• To make width A narrower, enter a negative

value.

8. Touch “END.”

9. Touch “OK.”

10. Touch “Exit” on the Service Mode screen.

11. Make a copy and check the punch hole positions

again.

VI. Punch regist loop size adjustment

1. Make a copy in the punch mode.

(Refer to the user’s guide (copy operations))

2. Check the tilt of the output paper.

• If it tilts, follow the procedures below for punch

loop adjustment.

3. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

4. Touch “Finisher.”

5. Touch “FS-FN adjustment.”

6. Touch “Punch Regist Loop Size.”

7. Set the correction value using the /

keys.

• To make loop length larger, enter a positive value.

• To make loop length smaller, enter a negative

value.

8. Touch “END.”

9. Touch “OK.”

10. Touch “Exit” on the Service Mode screen.

11. Make a copy again and check the deviance of

punch hole position.

4512IXE057DA

<North America:

2 holes>

<North America:

3 holes>

<Europe: 4 holes> <Sweden: 4 holes>

4512IXC056DA

4512IXE062DA4512IXE061DA

A10E-9550-01E.fm 3 ページ２００９年７月２日　木曜日　午後６時２３分

Other Konica Minolta Printer Accessories manuals

Konica Minolta

Konica Minolta FS-503 User manual

Konica Minolta

Konica Minolta magicolor 2430 DL User manual

Konica Minolta

Konica Minolta DK-510 User manual

Konica Minolta

Konica Minolta RU-513 User manual

Konica Minolta

Konica Minolta HD-524 User manual

Konica Minolta

Konica Minolta HT-509 User manual

Konica Minolta

Konica Minolta Di1611 User manual

Konica Minolta

Konica Minolta KIP Color 80 User manual

Konica Minolta

Konica Minolta WT-513 User manual

Konica Minolta

Konica Minolta bizhub C220 Series User manual

Konica Minolta

Konica Minolta LU-302 User manual

Konica Minolta

Konica Minolta LU-204 User manual

Konica Minolta

Konica Minolta IT-101 How to use

Konica Minolta

Konica Minolta bizhub 223 User manual

Konica Minolta

Konica Minolta PC-101 User manual

Konica Minolta

Konica Minolta bizhub 223 User manual

Konica Minolta

Konica Minolta Pi3505e User manual

Konica Minolta

Konica Minolta DF-704 User manual

Konica Minolta

Konica Minolta PK-511 User manual

Konica Minolta

Konica Minolta VI-506 User manual

Konica Minolta

Konica Minolta EK-608 User manual

Konica Minolta

Konica Minolta PI-506 User manual

Konica Minolta

Konica Minolta bizhub 361 User manual

Konica Minolta

Konica Minolta IP-011 How to use

Popular Printer Accessories manuals by other brands

Star Micronics

Star Micronics TSP800 Series install guide

REA

REA JET HR pro 2K user manual

HP Laserjet,Color Laserjet 4si user guide

oliser

oliser MS 45 instructions

Roland

Roland DU2-64 Supplementary manual

Xerox

Xerox EFI EXP6000 Specification sheet

Canon

Canon Finisher-T1 Service manual

Sharp

Sharp FO-1MK Service manual

Labelmate

Labelmate PM-300 user manual

Epson

Epson T6248 Product information sheet

Epson

Epson OT-BZ20 user manual

Canon

Canon TonerRobot EP-27 instruction manual

Ricoh

Ricoh LCIT RT5100 Field service manual

GBC

GBC 16 Series user guide

Canon

Canon INNER 2-WAY TRAY-E1 INSTALLATION PROCEDURE

Develop

Develop SD-509 installation manual

Kyocera

Kyocera KM-6230 Instruction handbook

Triumph Adler

Triumph Adler DF-710 Instruction handbook