Konica Minolta PI-505 User manual
E-1
INSTALLATION MANUAL
A10A-9550-00
PI-505 Post Inserter
Note:
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could
result in personal injury. When transporting the
machine, assign an adequate number of persons
to the job and ensure that each person can take a
good position of not being excessively loaded.
(mass: approx. 10.5 kg (23-1/4 lb))
I. Accessory parts
Note:
If the finisher has the punch kit installed, prepare a
short screwdriver that is used in installing the post
inserter.
No. Name Shape Q’ty
1. Post inserter
1
2. Cover
1
3. Connector
cover
1
4. Screw cover
4
5. Positioning
screw 2
6. Screw A
(4 x 6 mm) 3
7. Screw B
(4 x 6 mm) 1
8. Screw C
(4 x 8 mm) 2
9. Label A 1
set
A07VIXC001DA
A10AIXC012DA
A07VIXC002DA
A10AIXC022DA
A07VIXC004DA
A07UIXC067DA
A092IXC012DA
9J08IXC080DA
10. Label B
1
11. Installation
manual
1
set
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
No. Name Shape Q’ty
4980IXC019DA
Applied Machine: FS-526
E-2
II. Installation Procedures
Note:
• When mounting the post inserter, mount it
before mounting the finisher to the machine.
• When mounting the punch kit at the same time,
mount the post inserter first.
• When handling the post inserter, grip it as
shown in the illustration below.
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Remove protective tape and protective material.
3. Remove two screw covers and two screws, and
remove the upper cover (small).
4. Remove three screw covers from the upper cover
(large) and remove three screws.
5. Open the front door of the finisher and remove
two screws that hold the upper cover (large).
A07VIXC005DA
A07VIXC006DA
A07VIXC007DA
A10AIXC001DA
A10AIXC002DA
➂
➁
➀
A10AIXC003DA
E-3
6. Remove the upper cover (large).
7. Install two of the screws that were removed at
step 4 at the locations as shown in the illustration.
Note:
Do not use the screw ➂.
8. Attach the cover furnished with the post inserter
(two screws C furnished with the post inserter).
9. Install two positioning screws furnished with the
post inserter at the locations as shown in the illus-
tration.
10. Install the post inserter to the finisher.
Note:
Place the post inserter in a location where the
positioning screw is fit into the hole as shown in
the illustration. Then slide the post inserter in the
direction of the arrow.
11. Connect the post inserter’s two connectors to
the finisher’s connectors.
A10AIXC004DA
A10AIXC006DA
A10AIXC007DA
A10AIXC008DA
A07VIXC013DA
A10AIXC010DA
E-4
12. Secure the post inserter (three screw A’s fur-
nished with the post inserter).
13. Attach the connector cover furnished with the
post inserter (one screw B furnished with the
post inserter).
14. Attach four screw covers furnished with the post
inserter.
15. Mount the finisher to the machine.
Note:
For the finisher mounting procedures, see installa-
tion manual for finisher.
A07VIXC015DA
A10AIXC011DA
A07VIXC017DA
A10AIXC016DA
E-5
III. Label Attachment
1. Affix the label A furnished with the post inserter to
the post inserter operation section as shown in
the illustration.
Note:
Depending on the punch hole type to be used, a
different number of the label is affixed to a different
location.
2. Open the finisher front door and affix the label B
furnished with the post inserter as shown in the
illustration.
A10AIXE018DA
A10AIXE019DA
A10AIXE020DA
<2-3 punch holes>
<2-4 punch holes>
<SW4 punch holes>
A10AIXC021DA
E-6
IV. Paper size detection
1. Plug the power cord into the power outlet and
turn on the machine.
2. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
3. Touch “Finisher.”
4. Touch “FS-FN adjustment.”
5. Touch “Post Inserter Adjustment.”
6. Touch “Upper Tray” on the screen and load
A4 in the upper tray.
7. Press the Start key.
8. Make sure that “Adj. Result” is “OK.”
9. Touch “Lower Tray” on the screen and load
A4 in the lower tray.
10. Press the Start key.
11. Make sure that “Adj. Result” is “OK.”
12. Keep touching “OK” until the service mode
screen is displayed.
13. Touch “Exit” on the Service Mode screen.
14. Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the main power after exiting the Service
Mode screen and wait for 10 seconds or more
before turning on.
15. Make sure that the following paper sizes are cor-
rectly detected.
<Metric area>
Upper tray: A4 , A4
Lower tray: A3 , A4 , A4
<Inch area>
Upper tray: Letter , Letter
Lower tray: Ledger , Letter , Letter
Table of contents
Other Konica Minolta Printer Accessories manuals
Konica Minolta
Konica Minolta PK-511 User manual
Konica Minolta
Konica Minolta PC-410 User manual
Konica Minolta
Konica Minolta bizhub C220 Series User manual
Konica Minolta
Konica Minolta PI-506 User manual
Konica Minolta
Konica Minolta FS-532 User manual
Konica Minolta
Konica Minolta HT-502 User manual
Konica Minolta
Konica Minolta PK-517 User manual
Konica Minolta
Konica Minolta LU-302 User manual
Konica Minolta
Konica Minolta Image Controller IC-205 User manual
Konica Minolta
Konica Minolta KIP Color 80 User manual
Konica Minolta
Konica Minolta bizhub 361 User manual
Konica Minolta
Konica Minolta IP-011 How to use
Konica Minolta
Konica Minolta PC-101 User manual
Konica Minolta
Konica Minolta magicolor 2430 DL User manual
Konica Minolta
Konica Minolta ViZion DR+ 1417V2 Use and care manual
Konica Minolta
Konica Minolta AD-509 User manual
Konica Minolta
Konica Minolta AU-201S User manual
Konica Minolta
Konica Minolta HT-509 User manual
Konica Minolta
Konica Minolta EK-608 User manual
Konica Minolta
Konica Minolta Image Controller IC-402 User manual
