Konica Minolta DF-601 User manual
E-1
DF-601 Automatic Document Feeder
4582-7701-03
INSTALLATION MANUAL
Applied Machine: C250
COLOR MFP 25 ppm
for Product Code 4038
I. Accessory parts II. Installation procedures
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Remove the two hinge covers at two places
(one screw each).
Note:
When the spacer is mounted, remove the spacer.
3. Screw the shoulder screws furnished with the
Automatic Document Feeder into the holes in the
rear (one screw each).
No. Name Shape Q’ty
1. Shoulder screw
2
2. Mounting screw
2
3. Chart
1
4. Installation
Manual
1
set
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting your head in the wrapper involves
danger of suffocation.
4582U010AA
4582U011AA
4980IXC019DA
4582IXC002DB
Spacer
4582IXC001DA
E-2
4. Place the Automatic Document Feeder in posi-
tion.
Note:
When installing the Automatic Document Feeder,
hold onto the upper and lower ends of the Auto-
matic Document Feeder in the vertical position as
shown on the left.
5. Using the two mounting screws furnished with
the Automatic Document Feeder, tighten the
hinges to secure the Automatic Document
Feeder in position.
Note:
Check that the shoulder screws are fully tight-
ened.
6. Remove the plastic bag of the hookup cable.
7. Connect the hookup cable to the machine.
III. Adjusting the Document Feeding Tray
Width
1. Plug the power cord into the power outlet and
turn on the machine.
2. Widen the width across the edge guides by slid-
ing them to their maximum width.
3. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the Service Manual.)
4. Touch “ADF.”
5. Touch “Original Tray Width.”
C4652U012AA
4582U001AD
4582U018AA
4582U013AA
4037IXE295DA
4582IXE508DA
E-3
6. Touch “Max. Width” and then press the Start key.
Check that “Adjustment Result” is “OK.”
7. Narrow the width across the edge guides by slid-
ing them to their minimum width.
8. Touch “Min. Width” and then press the Start key.
Check that “Adjustment Result” is “OK.”
9. Touch “END.”
10.Touch “Exit” on the Service Mode screen.
IV. Checking and Adjusting Document
Skew
1. Place the chart in the document feeding tray (with
the side having an arrow facing up).
2. Set up the following functions:
• Select the tray in which A4 crosswise or Letter
crosswise paper is loaded.
• 1-sided original 1-side copy
3. Press the Start key.
4. Check in which direction, A or B, the image tilts
on the copy fed out of the machine.
Specifications: Tilt 3 mm max.
* If the image tilts more than the specifications, per-
form the following steps to make the adjustment.
4582IXE509DA
4582U014AA
4582IXE510DA
4582U003AA
▲
4582U006AC
E-4
5. Loosen the two front screws on the right hinge.
If the gap A is wider than gap B, move the Auto-
matic Document Feeder toward the front.
If the gap B is wider than gap A, move the Auto-
matic Document Feeder toward the rear.
Note:
Do not move the Automatic Document Feeder to
the frontmost or leftmost position.
6. Tighten the two screws.
7. Make the copy and check again.
V. Checking and Adjusting the Document
Feeding Tray Reference Position
1. Place the chart in the document feeding tray
(with the side having an arrow facing up).
2. Set up the following functions:
• Select the tray in which A4 crosswise or Letter
crosswise paper is loaded.
• 1-sided original 1-side copy
3. Press the Start key.
4. Fold the copy in half.
5. With reference to the crease, check to see if the
arrow is on the side of A or B.
Specifications: ± 2 mm from the center
* If the deviation falls outside the specified range,
use the following procedure to make an adjust-
ment.
4582U007AC
4582U003AA
▲
A
B
<Metric Areas for standard line>
A
B
<Inch Areas for standard line>
E-5
6. Loosen the screw (two on the front side and three
on the backside) on the document feeding tray.
If the crease deviates on the side of A, move the
tray to the front.
If the crease deviates on the side of B, move the
tray to the rear.
7. Tighten the five screws.
8. Make the copy and check again.
VI. Adjusting the Document Stop Position
1. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the Service Manual.)
2. Touch “ADF.”
3. Touch “Auto Stop Position Adjustment.”
4. Touch “Sub Scanning Direction 1-Side.”
4582U005AC 4037IXE295DA
4582IXE508DA
4582IXE003DA
E-6
5. Place the chart in the document feeding tray
(with the side having an arrow facing up).
6. Press the Start key.
7. Make sure that “Adjustment Result” is “OK.”
Then, touch “SET.”
8. Touch “Sub Scanning Direction 2-Side.”
9. Place the chart in the document feeding tray.
Note:
Make sure that the blank surface of the chart
faces up.
10.Press the Start key.
11.Check that “Adjustment Result” is “OK” and then
touch “SET.”
12.Touch “Main Scanning Direction.”
13.Place the chart in the document feeding tray
(with the side having an arrow facing up).
14.Press the Start key.
15.Check that “Adjustment Result” is “OK” and then
touch “SET.”
16.Touch “END.”
17.Touch “Exit” on the Service Mode screen.
18.Turn OFF and ON the Main Power Switch.
Note:
When displayed the Service Mode screen, be
sure to turn off the main power after exiting the
Service Mode screen and wait for 10 seconds or
more before turning on.
VII. Fixing the Stoppers
Loosen the stopper screws (two each on the right
and left). Then, with the stoppers raised, tighten the
screws.
4582U003AA
4582IXE512DA
4582IXE513DA
4582IXE514DA
4582U009AB
4582U008AB
Other Konica Minolta All In One Printer manuals
Konica Minolta
Konica Minolta bizhub 223 User manual
Konica Minolta
Konica Minolta BIZHUB C250 User manual
Konica Minolta
Konica Minolta bizhub 750 User manual
Konica Minolta
Konica Minolta BIZHUB 131F Setup guide
Konica Minolta
Konica Minolta bizhub 250 User manual
Konica Minolta
Konica Minolta bizhub 223 User manual
Konica Minolta
Konica Minolta bizhub C360i User manual
Konica Minolta
Konica Minolta bizhub C452 Series Instruction and safety manual
Konica Minolta
Konica Minolta BIZHUB C300 Instruction Manual
Konica Minolta
Konica Minolta bizhub C450 User manual
Konica Minolta
Konica Minolta bizhub 652 User manual
Konica Minolta
Konica Minolta bizhub C650 Series User manual
Konica Minolta
Konica Minolta Bizhub C3350 User manual
Konica Minolta
Konica Minolta BIZHUB C252 User manual
Konica Minolta
Konica Minolta Bizhub 362 User manual
Konica Minolta
Konica Minolta bizhub C35P Original instructions
Konica Minolta
Konica Minolta Bizhub C3350 User manual
Konica Minolta
Konica Minolta bizhub C25 User manual
Konica Minolta
Konica Minolta magicolor 2400W User manual
Konica Minolta
Konica Minolta bizhub PRO 950 Series User manual
