Kohler K-45209 User manual
Installation Guide
Shower Column
Mproduct numbers are for Mexico (i.e., K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página“ Español-1”
1381580-2-A
Tools and Materials
Before You Begin
NOTE: This guide includes the installation sequence for the shower
column only. Install the mixing valve, mixing valve trim, and spout
according to the manufacturer’s instructions.
NOTICE: Risk of product damage. Do not apply excessive weight
or downward force to the shower column.
CAUTION: Risk of property damage. Water leakage may
occur if supply piping allows movement. Verify that the
supply piping and 1/2″-14 NPT elbow fitting are securely
fastened to braces in the stud framing.
NOTE: The showerhead, hose, and handshower are purchased
separately.
Please read all instructions before you begin.
Observe all local plumbing and building codes.
Shut OFF the water supply.
Inspect the existing supply piping and wall materials. Replace if
necessary.
Sealant Tape
3/8"
100% Silicone Sealant
1/2"
1381580-2-A 2 Kohler Co.
Before You Begin (cont.)
The shower column is supplied with toggle anchor fasteners for
installation onto a finished wall surface. The finished wall
thickness must be a minimum of 5/8″(16 mm) and must be
adequate in strength. Two toggle anchor fasteners are required
per mounting collar.
IMPORTANT! If the supplied toggle anchor fasteners are not used
to install the shower column:
Verify that adequate strength wall backing materials and stud
bracing are properly positioned behind the finished wall.
Obtain proper fasteners (not provided) taking into account the
type of stud bracing material and thickness of the mounting
collar, finished wall, wall backing, and stud bracing.
Fasteners must be corrosion-resistant and capable of 300 lbs (136
kg) load bearing per fastener.
A minimum of two fasteners are required per mounting collar.
Fasteners must be securely anchored into the stud bracing to
adequately support the product.
IMPORTANT! For retrofit/remodel installations: Check the existing
shower enclosure for adequate clearances before proceeding with the
shower column installation. Refer to the Specification Sheet for the
shower column and showerhead.
Verify the distances between:
•The ceiling and the center of the existing shower arm at the
finished wall surface.
•The shower floor and the center of the existing shower arm at the
finished wall surface. Verify sufficient clearance under the
showerhead.
•The center of the existing shower arm and the center of the
mixing valve trim.
Kohler Co. 3 1381580-2-A
Roughing-In - Upper Supply Connection
Measure the distance between the 1/2″-14 NPT elbow and the
finished wall surface. The distance must be between 1-3/8″(35
mm) and 2-7/8″(73 mm).
IMPORTANT! The shower column connection will not seal
properly if the distance exceeds 2-7/8″(73 mm); see below for the
required deep roughing-in kit.
If the distance is between 2-7/8″(73 mm) and 4″(102 mm):
Order the 1194630 Deep Roughing-in Kit.
If the distance is less than 1-3/8″(35 mm): Order the 1187917
Shallow Roughing-in Kit.
1" (25 mm) Max
Wall Surface Offset
1/2"-14 NPT Elbow
1-3/8" (35 mm) Min
2-7/8" (73 mm) Max
1-3/4" (44 mm) Min
Escutcheon Clearance
Finished Wall Surface
1381580-2-A 4 Kohler Co.
Roughing-In
3-3/4"
(95 mm)
27"
(686 mm)
18-5/8" (473 mm)
18-5/8" (473 mm)
9-1/2"
(241 mm)
27"
(686 mm)
K-45210 (Less Showerhead, Handshower, and Hose)
K-45209 (Less Showerhead, Handshower, and Hose)
Backing
Material
Backing
Material
6" (152 mm)
Min
6" (152 mm)
Min
75" (1905 mm)
Recommended
72" (1829 mm)
Min
80" (2032 mm)
Recommended
75" (1905 mm)
Min
Kohler Co. 5 1381580-2-A
Roughing-In
18"
(457 mm)
18-5/8" (473 mm)
18"
(457 mm)
9-1/2"
(241 mm)
18-5/8" (473 mm)
3-3/4"
(95 mm)
K-45212 (Less Showerhead, Handshower, and Hose)
K-45211 (Less Showerhead, Handshower, and Hose)
Backing
Material
78" (1681 mm)
Recommended
75" (1905 mm)
Min
75" (1905 mm)
Recommended
72" (1829 mm)
Min
6" (152 mm)
Min
6" (152 mm)
Min
Backing
Material
1381580-2-A 6 Kohler Co.
1. Retrofit/Remodel Installation
CAUTION: Risk of property damage. Water leakage may
occur if supply piping allows movement. Verify that the
supply piping and 1/2″-14 NPT elbow fitting are securely
fastened to braces in the stud framing.
IMPORTANT! Check the existing shower enclosure for adequate
clearances as described in the ″Before You Begin″section.
Remove the existing showerhead and shower arm escutcheon.
Carefully push the existing shower arm toward the finished wall
surface.
Check for inward movement of the supply piping.
If inward movement is possible, securely fasten the supply piping
to braces in the stud framing before beginning the shower column
installation.
Remove the existing shower arm.
Measure the existing shower arm hole. Verify that the finished
wall material has an upper supply connection hole diameter
between 1″(25 mm) minimum and 1-1/4″(32 mm) maximum,
and the hole is centered on the outlet of the 1/2″-14 NPT elbow
fitting. Repair the wall surfaces if the existing shower arm hole is
not centered or exceeds the recommended dimensions.
Supply Piping
1/2"-14 NPT Elbow
Kohler Co. 7 1381580-2-A
2. Install the Supply Adapter
For New Construction Installations
CAUTION: Risk of property damage. Water leakage may
occur if supply piping allows movement. Verify that the
supply piping and 1/2″-14 NPT elbow fitting are securely
fastened to braces in the stud framing.
IMPORTANT! This guide includes the installation sequence for the
shower column only. Refer to the manufacturer’s instructions for
installation of the mixing valve, mixing valve trim, and spout.
Rough-in the mixing valve, supply piping, and bath spout
connection appropriate for your installation.
Refer to the ″Roughing-in″section in this guide for proper
location of the 1/2″-14 NPT elbow fitting inside the wall.
Verify that the supply piping and 1/2″-14 NPT elbow fitting are
securely fastened to the stud framing.
1/2"-14 NPT Elbow
1/2"-14 NPT Elbow
Supply Piping
1" (25 mm) Min
1-1/4" (32 mm) Max
Supply
Adapter
3/8" Hex
Wrench
1381580-2-A 8 Kohler Co.
Install the Supply Adapter (cont.)
Verify that the finished wall material has an upper supply
connection hole diameter between 1″(25 mm) minimum and
1-1/4″(32 mm) maximum, and the hole is centered on the outlet
of the 1/2″-14 NPT elbow fitting.
If your supply connection hole diameter is between 1-1/4″(32
mm) and 2-1/4″(57 mm): Order the 1194302 Large
Escutcheon/Mounting Collar Kit.
Install the finished wall material.
Install the mixing valve trim and bath spout according to the
manufacturer’s instructions.
For New Construction and Retrofit Installations
Apply sealant tape to the supply adapter thread.
The supply adapter has an internal 3/8″hex socket. Thread the
supply adapter into the 1/2″-14 NPT elbow using a 3/8″hex
wrench.
Kohler Co. 9 1381580-2-A
3. Mark the Mounting Hole Locations
NOTE: The upper mounting collar must be centered on the supply
adapter. The distance between the upper and lower mounting collar
centers should be 18″(457 mm) or 27″(686 mm) depending on the
length of your shower column.
Center the mounting collar on the supply adapter. Mark the left
and right mounting holes.
For K-45209/K-45210 only: From the center of the supply adapter,
measure down 27″(686 mm) and mark the horizontal
measurement with a pencil.
For K-45211/K-45212 only: From the center of the supply adapter,
measure down 18″(457 mm) and mark the horizontal
measurement with a pencil.
Center the mounting collar on the horizontal line. Measure and
mark the left and right mounting holes. Verify the upper and
lower mounting-hole locations are level and plumb to one
another.
Do not drill the mounting holes until instructed to do so.
K-45209,K-45210,
27" (686 mm)
K-45211,K-45212,
18" (457 mm)
Supply Adapter
Mounting
Collar
Mounting Collar
2" (51 mm)
1381580-2-A 10 Kohler Co.
This manual suits for next models
3
Table of contents
Languages:
Other Kohler Bathroom Fixture manuals
Kohler
Kohler K-15996 Assembly instructions
Kohler
Kohler Mira Advance 8.7 User manual
Kohler
Kohler FAMILY CARE K-706264T-FM-SHP User manual
Kohler
Kohler K-T398 User manual
Kohler
Kohler K-1118-LA Quick start guide
Kohler
Kohler C3-255 Assembly instructions
Kohler
Kohler K-6525 User manual
Kohler
Kohler TEND K-20713T-ET User manual
Kohler
Kohler K-702205 User manual
Kohler
Kohler Rada PA-TF User manual
Kohler
Kohler K-113 User manual
Kohler
Kohler K-9132 Assembly instructions
Kohler
Kohler K-610 Assembly instructions
Kohler
Kohler K-817 User manual
Kohler
Kohler Components K-77980-4A-CP User manual
Kohler
Kohler K-9674 User manual
Kohler
Kohler K-24985K Assembly instructions
Kohler
Kohler K-2746T-1/8 User manual
Kohler
Kohler K-702300 Assembly instructions
Kohler
Kohler IRON/IMPRESSIONS K-3051-8 User manual
