Kohler K-2834 User manual
Installation Guide
Above-Counter Lavatory
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-2834
1061942-2-B
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Tools and Materials
Before You Begin
CAUTION: Risk of personal injury or product damage. Cast
iron lavatories are very heavy. Get help lifting the lavatory
into place.
CAUTION: Risk of product damage. When securing the
lavatory to the countertop/vanity, use the type of sealant
recommended by the countertop/vanity manufacturer. Refer
to the countertop/vanity manufacturer’s instructions for this
information, as certain sealants may damage the finish of the
countertop/vanity.
Observe all local plumbing and building codes.
If you are replacing an existing lavatory, turn off the water supply
to the faucet. Open the faucet valves to relieve pressure, then
disconnect the supply lines. Disconnect the drain assembly,
remove the trap, then remove the lavatory.
For new installations, ensure the water supply lines, drain piping,
vanity, and/or countertop is in place before proceeding with the
lavatory installation.
Pencil
Scissors
Drill
• Template (supplied)
• Rags or Paper Toweling
• Assorted Drill Bits
• Marker
• Sealant recommended by
countertop/vanity
manufacturer
Plus:
Tape
Measure
Safety
Glasses
Jigsaw
Masking
Tape
Adjustable
Wrench
1061942-2-B 2 Kohler Co.
Before You Begin (cont.)
When selecting a faucet for the lavatory, ensure the spout will
reach a minimum of 4″(10.2 cm) over the rim of the lavatory and
the stream of water is directed toward the center of the lavatory
basin.
Never rest or store the lavatory on the drain surface or threaded
studs.
Prior to installation, unpack the new lavatory and inspect it for
damage. Return the lavatory to its protective carton until you are
ready to install it.
For replacement installations, make sure the existing cutout is the
same size or smaller than needed for the new lavatory.
You can choose between a wall-mount or countertop faucet
installation, depending upon the setting and styling you desire. A
wall-mount faucet is recommended.
If installing multiple components (such as a cabinet, countertop,
or lavatory) read all product installation instructions before
beginning. Some components should be installed before others.
Kohler Co. reserves the right to make revisions in the design of
products without notice, as specified in the Price Book.
Kohler Co. 3 1061942-2-B
Roughing-In
NOTE: To determine the faucet and lavatory placement, consider the
faucet and handle escutcheon diameters, the length of the spout,
and the clearance between the spout and the lavatory rim. Ensure:
•the faucet spout will reach a minimum of 4″(10.2 cm) over the
rim of the lavatory.
•adequate clearance for hand washing.
•the stream of water is directed toward the center of the lavatory
basin.
4-3/16"
(10.6 cm)
5-9/16"
(14.1 cm)
1-7/16"
(3.7 cm)
22" (55.9 cm)
18"
(45.7 cm)
9"
(22.9 cm)
11"
(27.9 cm)
1-1/4" OD
3/8" Cold3/8" Hot 4"
(10.2 cm)
12-7/8"
(32.7 cm)
14"
(35.6 cm)
1061942-2-B 4 Kohler Co.
1. Prepare the Site
For Installations with a Countertop Faucet
Determine the faucet centerline location. Refer to the roughing-in
information provided with your faucet.
Carefully draw the calculated faucet centerline on the cut-out
template.
Cut along the ″above-counter cut-out″line on the cut-out
template with a scissors.
Using the centerlines as a guide, squarely position the cut-out
template on the countertop to ensure clearance between the
lavatory, faucet, and backsplash.
Use a pencil to trace around the ″above-counter cut-out″line on
the countertop.
NOTE: Ensure the faucet spout will reach a minimum of 4″(10.2
cm) over the rim of the lavatory and the stream of water is directed
toward the center of the lavatory basin.
Recheck the clearance between the lavatory, faucet, and
backsplash. Adjust the traced cut-out line, if necessary.
Use a pencil to mark the: (1) exact center of the four mounting
hole locations on the countertop, and (2) faucet and handle
centerline on the countertop.
IMPORTANT! Do not cut the marked faucet and handle locations
until instructed to do so.
Outside Edge
of Lavatory
Cut-out Line
Backsplash
Kohler Co. 5 1061942-2-B
Prepare the Site (cont.)
Remove the cut-out template.
Cut along the inside of the marked pencil line for the lavatory
with a jigsaw.
Slowly drill the four 3/8″(1 cm) diameter mounting holes at the
marked center.
For Installations with a Wall-Mount Faucet
Cut along the ″above-counter cut-out″line on the cut-out
template.
Using the centerlines as a guide, squarely position the cut-out
template on the countertop to ensure clearance between the
lavatory and faucet.
Use a pencil to trace around the ″above-counter cut-out″line on
the countertop.
NOTE: Ensure the faucet spout will reach a minimum of 4″(10.2
cm) over the rim of the lavatory and the stream of water is directed
toward the center of the lavatory basin.
Recheck the clearance between the lavatory and faucet. Adjust the
traced cut-out line, if necessary.
Use a pencil to mark the exact center of the four mounting hole
locations on the countertop.
Remove the cut-out template.
Cut along the inside of the marked pencil line with a jigsaw.
Drill the four 3/8″(1 cm) diameter mounting holes at the marked
centers.
1061942-2-B 6 Kohler Co.
2. Install the Lavatory
CAUTION: Risk of personal injury or product damage. Cast
iron lavatories are very heavy. Get help lifting the lavatory
into place.
Mark a spot 5/16″(8 mm) in on each threaded stud, as shown.
Hand-tighten the threaded studs into each of the four drilled
mounting holes to the marked point.
Temporarily position the lavatory in the countertop cutout so the
″Kohler″logo is to the back.
Inspect for proper fit.
Remove the lavatory, then place it upside down on a soft cloth.
If applicable, drill the faucet hole(s) and handle location(s) at this
time.
Install the faucet according to the manufacturer’s instructions.
Install the drain to the lavatory according to the drain installation
instructions.
5/16" (8 mm)
Marker
Mounting Stud Holes
Bottom View
of Lavatory
Kohler Co. 7 1061942-2-B
Install the Lavatory (cont.)
Apply a thin continuous bead of sealant around the flat outside
edge of the bottom surface of the lavatory. Refer to the
countertop/vanity manufacturer’s instructions for the
recommended type of sealant.
Carefully position the lavatory in the countertop cutout so the
″Kohler″logo is to the back.
Thread a washer and nut onto each of the threaded studs from
underneath the countertop.
Hand-tighten the nuts, then turn the nuts another 1/2 turn with
an adjustable wrench.
Wipe away any excess sealant with a clean cloth. Fill any voids as
needed.
Allow the sealant to cure for at least 30 minutes before
proceeding.
3. Installation Checkout
Connect and tighten the trap to the drain, and complete the water
supply connections to the faucet according to the instructions
packed with the faucet.
Run water into the lavatory and check for leaks.
Clean up with a non-abrasive cleaner.
1061942-2-B 8 Kohler Co.
Guide d’installation
Lavabo sur comptoir
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Nous apprécions votre engagement envers la qualité Kohler. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de performance. Nos numéros de téléphone
et notre adresse du site internet sont au verso. Merci encore d’avoir
choisi la compagnie Kohler.
Avant de commencer
ATTENTION : Risque de blessure corporelle ou
d’endommagement du produit. Les lavabos en fonte sont
très lourds. Demander de l’assistance pour soulever et mettre
en place ce lavabo.
ATTENTION : Risque d’endommagement du produit. Lors
de la fixation du lavabo sur le comptoir/meuble, utiliser le
type de mastic recommandé par le fabricant du
comptoir/meuble. Se référer aux instructions du fabricant du
comptoir/meuble pour cette information car certains mastics
pourraient endommager la finition du comptoir/meuble.
Respecter tous les codes de plomberie et de bâtiment locaux.
Crayon
à papier
Ciseaux
Perceuse
• Gabarit (fourni)
• Chiffons et papier essuie-tout
• Mèches assorties
• Marqueur
• Mastic recommandé par
le fabricant du
comptoir/meuble.
Plus:
Mètre
ruban
Lunettes de
protection
Scie
sauteuse
Ruban-cache
Clé à
molette
Kohler Co. Français-1 1061942-2-B
Avant de commencer (cont.)
Dans le cas de remplacement d’un lavabo existant, couper
l’alimentation d’eau au robinet. Ouvrir les valves de robinet pour
libérer la pression et déconnecter les lignes d’alimentation.
Débrancher le drain, retirer le siphon et retirer le lavabo.
Pour de nouvelles installations, s’assurer que les lignes
d’alimentation d’eau, la tuyauterie du drain, meuble. et/ou le
comptoir soient en place avant de procéder à l’installation du
lavabo.
Lors de la sélection de robinet pour lavabo, s’assurer que le bec
atteigne un minimum de 4″(10,2 cm) au-dessus du rebord du
lavabo et que le jet d’eau soit dirigé vers le centre du bassin du
lavabo.
Ne pas laisser reposer le lavabo sur la surface du drain ou les
montants filetés.
Avant son installation, déballer le nouveau lavabo et l’examiner
pour en déceler tout dommage. Remettre le lavabo dans son
emballage de protection jusqu’à être prêt à l’installer.
Pour des installations de remplacement, s’assurer que la découpe
existante soit de la même taille ou plus petite que celle requise
pour le nouveau lavabo.
Vous pouvez choisir entre un robinet à montage mural ou sur
comptoir, selon le style désiré. Un robinet à montage mural est
recommandé.
Dans les cas d’installation de composants multiples (tels que
meuble, comptoir, ou lavabo), lire toutes les instructions
d’installation du produit avant de commencer. Certains éléments
doivent être installés avant d’autres.
Kohler Co. se réserve le droit d’apporter toutes modifications sur
le design des produits et ceci sans préavis, tel que spécifié dans le
catalogue des prix.
1061942-2-B Français-2 Kohler Co.
Table of contents
Languages:
Other Kohler Bathroom Fixture manuals
Kohler
Kohler Revival K-16131-4-PB User manual
Kohler
Kohler K-1226 User manual
Kohler
Kohler QUICK-RELEASE QUIET-CLOSE K-17608T User manual
Kohler
Kohler K-706139 Assembly instructions
Kohler
Kohler K-8501 Assembly instructions
Kohler
Kohler Mariposa K-1257-GLAW User manual
Kohler
Kohler K-1111-VLN User manual
Kohler
Kohler K-3082 User manual
Kohler
Kohler K-4917X Assembly instructions
Kohler
Kohler 76399T User manual
Kohler
Kohler K-17493 Assembly instructions
Kohler
Kohler K-9970 User manual
Kohler
Kohler PARALLEL 23492T-4 User manual
Kohler
Kohler Kumin 97878 Operating manual
Kohler
Kohler 12879T User manual
Kohler
Kohler Toobi K-T8975 Assembly instructions
Kohler
Kohler K-355 User manual
Kohler
Kohler 10-Jet K-1000-H2 User manual
Kohler
Kohler Joure 14682-4 User manual
Kohler
Kohler C3-255 Assembly instructions
