Kogan KAHUDA5CARA User manual

Table of contents

Other Kogan Monitor manuals

Popular Monitor manuals by other brands

Linear Acoustic

Linear Acoustic LQ-1000 user guide

AOC

AOC I2579V user manual

Gateway

Gateway FPD1520 user guide

Furuno

Furuno Mu 120c Operator's manual

Asus

Asus VB171D - 17" LCD Monitor Service manual

Dell

Dell S2230MX Setting up

Philips

Philips 107C64 user manual

Dell

Dell S2409WFP user guide

EverFocus

EverFocus EN-7517E instruction manual

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Service manual

Dell

Dell Precision 7680 Connection guide

LG

LG 50PM1M - - 50" Plasma Panel Service manual

Bosch

Bosch DDU 9 manual

Acer

Acer A231HL user manual

Philips

Philips 86BDL4152T user manual

NEC

NEC AccuSync LCD5V user manual

Emay

Emay SleepO2 user manual

IBM

IBM 6360 Product support manual

CAR HEAD UP DISPLAY

KAHUDA5CARA

Head up display (HUD)

Charging cable

Non-slip mat

Reflective film

User guide

COMPONENTS

Display (as viewed on windscreen)

1. Buzzer

2. Setting

3. Compass

4. Satellite

5. Speed

6. Light sensor

7. Speed unit (MPH/ Km/h)

OVERVIEW

Input

button

Before First Use

1. Place the non-slip mat on the driver’s side corner of the dashboard and then place

the head up display (HUD) on it.

2. Connect charger to vehicle’s 12V socket.

3. Connect the cable to the OBDII input on the unit.

4. Start the engine and the HUD will power on.

5. The RED satellite icon will flash when charged and begin searching for a satellite

connection. When the satellite indicator turns GREEN, the HUD is ready for use.

Reflective Film

The HUD projects information up onto the windscreen. Due to the construction of your

windscreen, the HUD may create a double reflection on the windscreen, which will make it

difficult to read. If this occurs, install the reflective film.

1. Spray some water onto the inside of your windscreen above where the HUD is

installed. Clean the area with a dry cloth.

2. Remove the backside (marked 1) of the film and apply to the windscreen.

3. Ensure the film is installed in the correct location and adjust if necessary.

4. Use a flat plastic object (credit card) to squeeze out any water or bubbles from

behind the reflective film.

5. Remove the protective film (marked 2).

6. If the reflective film isn’t positioned to display all the vehicle information, adjust the

position of the HUD and non-slip mat until it is correctly aligned.

INSTALLATION

Input button:

The Input button is a three-way button used to navigate the HUD’s menu and adjust the

settings.

• Up: push the button towards the windscreen

• Ok: press the button inwards

• Down: pull the button towards the driver

Using the input button

Press and hold the input button for 5 seconds to enter the menu. When finished adjusting

the settings, press and hold the input button for 5 seconds to save changes and exit.

• Up: increases setting value

• Down: decrease setting value

• Down and hold: turn alarm tone on or off

• Ok: short press to change menu selection

Factory Reset

Long pull up and hold. When all LEDs are illuminated, the HUD has been restored to

factory settings.

OPERATION

Up

Down

Ok

Settings menu

Since the HUD receives data from satellites, the data will vary slightly from the information

displayed on the vehicle dashboard. If you find the value on your dashboard is different to

the value displayed by the HUD, you can change it through the following procedure.

Menu

Parameter

Adjustment

range

Explanation

Default

Display

1

Speed

80-120

Up or down to adjust

107

2

Over-speed

alarm

10-180

Sounds alarm when

speed is exceeded

117

3

Brightness

0-5

1 (darkest) – 5 (brightest)

0 = Automatic

100

4

Speed unit

0-1

0= Km/h

1= MPH

50

5

Power on/off

voltage

100-150

Change to 13.2V-14V if

HUD does not turn off

automatically

45

6

Display mode

0-1

0 = reflect on windshield

1 = HUD screen

0

Working voltage

DC8-18V

Current

Working: 40mA

Standby: 15mA

Speed range

0-400km

Satellite positioning time

Cold start: 4 mins

Hot start: 45 seconds

Compass precision

±1°

12V car charger

1000mA

Weight

40g

Dimensions

90x54x12mm

SPECIFICATIONS

Issue

Solution

HUD has no display/power

• Ensure the power cable is properly connected

• Press the input button down multiple times

• Connect the HUD to a different 12V socket or

another vehicle to ensure the 12V is functioning

correctly

Inaccurate speed

• Ensure the speed unit is correct (MPH/Km/h)

• Adjust the speed value in the settings menu

HUD is not visible in sunlight

• Ensure the reflective film is installed

• Adjust the brightness in the settings menu

TROUBLESHOOTING

NOTES