Knightsbridge SN3P Instruction Manual

INSTALLATION & MAINTENANCE MANUAL

SN3P / SN4P

These instructions should be read carefully and retained after installation by the

end user for future reference and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

GENERAL INSTRUCTIONS

SAFETY

INSTALLATION

• This product must be installed in accordance with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building Regulations. If in any doubt, consult a

qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Please note the IP (Ingress Protection) rating of this product when deciding the location

for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is for indoor use only

• This product is IP20 rated

• Provide power to the required point of installation

• Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Do not overload this accessory or subject it to conditions outside its rating

•This product is for indoor use only

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

Fig. 1

•Squeeze the sides of each half together to remove the cover (see Fig. 2)

Fig. 2

•Ensuring correct polarity is observed, carefully wire the supply side of the connector as shown in Fig. 3

Fig. 3

•Connect the load side ensuring the correct polarity is observed (see Fig. 4)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Do not overload this accessory or subject it to conditions outside its rating

•This product is for indoor use only

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

Fig. 1

•Squeeze the sides of each half together to remove the cover (see Fig. 2)

Fig. 2

•Ensuring correct polarity is observed, carefully wire the supply side of the connector as shown in Fig. 3

Fig. 3

•Connect the load side ensuring the correct polarity is observed (see Fig. 4)

• Squeeze the sides of each half together to remove the cover (see Fig. 2)

• Ensuring correct polarity is observed, carefully wire the supply side of the connector as

shown in Fig. 3

Fig. 1

Fig. 2

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Do not overload this accessory or subject it to conditions outside its rating

•This product is for indoor use only

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

Fig. 1

•Squeeze the sides of each half together to remove the cover (see Fig. 2)

Fig. 2

•Ensuring correct polarity is observed, carefully wire the supply side of the connector as shown in Fig. 3

Fig. 3

•Connect the load side ensuring the correct polarity is observed (see Fig. 4)

Fig. 4

•Check all electrical connections are secure with all exposed copper within the terminal and no loose

strands of cable

•Refit the covers ensuring that the cables are secured by the cord grip

•Push the two halves together until the tab clicks into place

•Switch on and check for correct operation

GENERAL

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of

purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product specification without prior notice.

230V 50Hz, IP20, indoor only

DCxxx22_V1

• Connect the load side ensuring the correct polarity is observed (see Fig. 4)

• Check all electrical connections are secure with all exposed copper within the terminal and

no loose strands of cable

• Reﬁt the covers ensuring that the cables are secured by the cord grip

• Push the two halves together until the tab clicks into place

• Switch on and check for correct operation

Fig. 3

Fig. 4

GENERAL

WARRANTY

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which

may damage the product.

This product should be recycled in the correct manner when it reaches the end of its life.

Check local authorities for where facilities exist.

This product has a warranty of 1 year from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper

use, or removal of the batch code will invalidate the warranty. If this product should fail

within its warranty period, it should be returned to the place of purchase for a free of

charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

DCSEP22_V1

SUPPLIED BY:

(UK) MANUFACTURER ML ACCESSORIES LTD,

UNIT E CHILTERN PARK, BOSCOMBE ROAD,

DUNSTABLE LU5 4LT,

WWW.MLACCESSORIES.CO.UK

(EU) SLV LIGHTING GROUP,

DAIMLERSTRASSE 21-23,

52531 ÜBACH-PALENBERG, GERMANY

EMAIL: EPREL@GROUP.SLV.COM

MADE IN CHINA

This manual suits for next models

Table of contents

Other Knightsbridge Lighting Equipment manuals

Knightsbridge

Knightsbridge UCLCT4 Instruction Manual

Knightsbridge

Knightsbridge TNXQUADSTW Instruction Manual

Knightsbridge

Knightsbridge BL12ALEDEM Instruction Manual

Knightsbridge

Knightsbridge GDL2 Instruction Manual

Knightsbridge

Knightsbridge OS002 Instruction Manual

Knightsbridge

Knightsbridge KIT4B Instruction Manual

Knightsbridge

Knightsbridge TRLED EM Series Instruction Manual

Knightsbridge

Knightsbridge TRLED 1 Series Instruction Manual

Knightsbridge

Knightsbridge EMPOWERST Instruction Manual

Knightsbridge

Knightsbridge EMSWING Instruction Manual

Knightsbridge

Knightsbridge EMRNST Instruction Manual

Knightsbridge

Knightsbridge BATC Series Instruction Manual

Knightsbridge

Knightsbridge LEDM06 Series Instruction Manual

Knightsbridge

Knightsbridge RCTRGB Instruction Manual

Knightsbridge

Knightsbridge SPIKE5S Instruction Manual

Knightsbridge

Knightsbridge TRI Series Instruction Manual

Knightsbridge

Knightsbridge SPIKE5A Instruction Manual

Knightsbridge

Knightsbridge BATC Series Instruction Manual

Knightsbridge

Knightsbridge TNXQUADW Instruction Manual

Knightsbridge

Knightsbridge 12DC36 Instruction Manual

Knightsbridge

Knightsbridge EMXST Instruction Manual

Knightsbridge

Knightsbridge HBLR Instruction Manual

Knightsbridge

Knightsbridge BLED5BW Instruction Manual

Knightsbridge

Knightsbridge 12DC40 Instruction Manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions