Kenmore 25370124001 User manual

Installation Instructions

For A-Kit 22"

Please read ALL instructions before installing. Two

people are recommended to install this product. If

a new electrical outlet is required, have the outlet

installed by a qualified electrician before instalFmg

unit. See #5 in Preliminary Instructions following.

WINDOW SASH SEAL

2,/4"LONG HEX HEAD SCREW

Preliminary Instructions

Do the following before starting to install unit.

See illustrations below.

1. Check window opening size -the mounting

parts furnished with this air conditioner are

made to install in a wooden sill double-hung

window. The standard parts are for a window

opening of 30" (711 ram) minimum to 42"

(1067 mm) maximum width. Open sash to a

minimum of 19" (483 mm). (FIG. 1)

2. Check condition of window -all wood parts

of window must be in good shape and able to

firmly hold the needed screws. If not, make

repairs before installing unit.

3. Check your storm windows - you will need

1/2" (13 mm) clearance below window stool.

If storm window frame does not allow the

clearance required, correct by adding a piece

of wood as shown in FIG. 2, or by removing

storm window while room air conditioner is

being installed. (continued)

FIG. I _SASH T

19" MIN.

,:'M,,. l

STORMWINDOWFRAME

OR OTHER OBSTRUCTION

TOPANGLE

FOAMGASKET

WASHERHEAD

ASSEMBLY

SIDE RETAINER

SEAL-BOTi'OM RAILTO UNIT

ASSEMBLY

(R_GH'0

LOCI_IUT

3/4"LONG_BRACKET

FLATHEAD _

BOLT SILLANGLE

BRACKET

FIG. 2

STORM WINDOW FRAME

OR OTHER OBSTRUCTION

_SASH

19=MIN.

1/2"MIN 111/2" M_._1

IRED, ALONG

RE STOOL

FASTEN WITH TWO

NAILS OR SCREWS.

•309000904 (9704)

4. CHECK FOR ANYTHING THAT COULD

BLOCK AIRFLOW - check area outside

of window for things such as shrubs,

trees, or awnings. Inside, be sure

furniture, drapes, or blinds will not

stop proper airflow.

5. Check the available electrical service -

power supply must be the same as that

shown on the unit serial nameplate. (See

Owner's Guide for serial pLate location.)

Power cord is 48" long. Be sure you have an

outlet near. It is best to not use extension

cords!

All models have a 3-prong service plug to

provide proper service and safe positive

grounding. Do not change plug in any way.

Do not use an adapter plug. If your present

wall outlet does not match your plug, call a

qualified electrician to make the needed

change.

Avoid fire hazard or

electric shock. Do not usean extension

cord or an adapter plug. Do not remove

any prong from the power cord.

Groundinc

wall

Power supply

cord with 3-prone.

grounding plug

6. Carefu/ly unpack air conditioner - remove

all packing material. Protect floor or carpet

fi-om damage. Two people should be used to

move and install unit.

ToolsRequired

_] a large flat blade screwdriver

"] #2 Phillips screwdriver

_/ tape measure

_] adjustable wrench or pliers

_] sharp knife of razor blade

4pencil

Hardware (in plastic bag)

Washer Head

Locking Screw

Screw and

_ut

__ 3/4" Long Flat

Head Bolt and

Locknut

3/4" Long Hex.

Head Screw 3

Safety Lock 1

smtmg/e

Bracket 2

Top

Angle Side

Retainer

SCrew Front

Retaining

4ea.

2ea.

Window Mounting

Remove Chassis

To slide chassis from cabinet, hold cabinet

with left hand, while pulling on strap provided

at the front of the unit.

Do not remove formed foam at the front of the

unit.

_ml_Assemble Window

_Filler Panels

1. Place cabinet on floor, a bench, or a table.

2. Slide "I" section of window filler panel into

side retainer on the side of the cabinet (see

Figures 2-3). Do both sides.

STRAP NOTE: Do not use strap for lifting unit. It

is for sliding chassis WITHIN cabinet only (to aid

in cleaning, maintenance, etc.). Be CAREFUL of

sharp edges on coil fins.

FIG. 2 pIJ_TIC WINDOW FILLER

FRAME PANEL

SiDE

Install Top Angle and

;ide Retainers

1. Attach foam gasket to top angle and side

retainers as shown in FIG. 1.

t_[j

2. Insta!l top angle and side retainers mcabinet

as shown, using screws as shown.

FIG. I

FIG. 3

NR CONDmONER

CABINET

-4_ _

_NDOW

RULER

PANEL

3. Insert top and bottom legs of window filler

panel frame into channel in the top angle and

bottom rail. Do both sides.

4. Insert washer head locking screws (2) into

holes in top leg of filler panel frame (see

Step 6). Do not totally tighten. Allow leg to

slide freely. Screws will be tightened after

Step 6.

(continued)

:Place Cabinet in !lnstall Support

Window Bracket

.Open window. Mark

center of window stool.

.Hold each support bracket flush against

outside of sill, and tight to bottom of cabinet

as shown below. Mark brackets at top level

of sill, and remove.

2. "Place cabinet in window with bottom stool

angle firmly seated over window stool as

shown. Bring window down temporarily

behind top angle to hold cabinet in place.

STOOL

3. Shift cabinet left or right as needed to line up

center of cabinet on center line marked on

stool.

4. Fasten cabinet to window stool with 2 screws

into holes. (You may wish to pre-drill pilot

holes.)

5. Add bottom rail seal over screws to window

stool.

2 EACH REQ'D FOR EACH

SUPPORT BRACKET

Assemble sill angle bracket to support brackets

at the marked position, as shown. Hand

tighten, but allow for any changes later.

Install support brackets (with sill angle

brackets attached) to correct hole in bottom

of cabinet as shown.

•m _ ' ;._! i _

Seal i

%_i,2';

"\ //

3/4"LONGHEX-

HEADSCREW

4. Tighten all 6bolts securely.

Iocknuts

_J_ Extend Window Filler

_,Panels

1. Carefully raise window to expose filler panel

locking screws. Loosen screws so filler panels

slide easily.

2, Extend panels to fir window opening

completely. Tighten locking screws on top.

3. Close window behind top angle.

Install Window Lock

and Sash Seal

Trim sash seal to fit window width. Insert

into space between upper and lower sashes.

Install Chassis into

Cabinet and Install

Front to Unit

Liftchassis and carefully slide it into installed

cabinet.

Do not push on controls OR

finned coils. You could damage unit, or cur

hands.

Be sure chassis is firmly seated towards rear of

cabinet.

Refer to Owner's Guide for front instafiation.

SEAL

2. Attach right angle safety lock as shown.

(contined).

LOCK

headscrew

Thru-The-Wall Installation

NOTE: Consult local building codes prior to

instal/ation, or a qualified carpenter.

Carefully measure and cut an opening with the

following dimensions. See FIGS. 1 and 2.

Select Wall Location WIDTH "X" = 24-1/4" plus twice the

thickness of flaming material used.

This air conditioner has a slide-out chassis, so it

can be installed through an outside wall up to 7"

(178 ram) thick. IMPORTANT: Side louvers must

never be blocked.

NOTE: All parts needed for Thru-The-Wall

Installation are provided, except a wood frame,

shims, and 10 wood screws (#10-1" long

minimum (25 ram). Select a wall surface that:

1. does not support major structural loads such

as the frame construction at ends Of windows,

and under truss-bearing points, etc.

2. does not have plumbing or wiring inside.

3. is near existing electrical oudets, or where

another outlet can be installed.

4. faces, and is not blocked to the area to be

cooled.

5. allows unblocked airflow from rear sides and

end (outside) of installed air conditioner.

BPrepare Wall

,Prepare wall in frame construction (including

brick and stucco veneer). Working from inside

the room, End wall stud nearest the center of

area where air conditioner will be installed (by

sounding wall, or by magnetically Ending

nails).

2. Cut or knock out a hole on each side of center

stud.

3. Measure between inside edges of every other

stud as shown in FIG. 1.

FIG. I

(8.6 cm)

HEIGHT "Y" = 15-1/4" plus twice the

thickness of flaming material used.

UP TO

.Build a wooden sleeve with the INSIDE

dimensions of 24ol/4" in width and 15-1/4" in

height. Frame depth should be the same as

wall thickness. Fill in the space from the

opening to the studs with wood spacers, as

shown.

5. Nail frame to spacers with front flush with

arywaU.

NOTE: If wall thickness is 7" (178 mm) or more,

add aluminum flashing over bottom of flame

opening to assure no water can enter area

between inner and outer wall. 1"LONG FIG. 2

ALUMINUM FLASHIN(

OVER BO'I-I'OM OF FRAME

,"_ OVER

7' (178 ram)

iPrepare and Install

Cabinet

1. Slide chassis from cabinet. Refer back to Step 1

of Window Mounting.

2. Place cabinet into opening with bottom rail

resting firmly on bottom board of wooden

fx-ame.

3. Position cabinet to achieve proper slope for

water removal. (See FIG. 1 below.)

4. Secure bottom rail to wood frame with two

large wood screws I" (2.5 cm) long using the

two holes in the bottom of the channel resting

on frame. (See FIG. 2 following.)

OPTIONAL: Support brackets may be used.

Installation brackets are recommended for walls

under 5" thick.

Refer to Step 4 of W'mdow Mounting for

assembly of support braekets. A wooden strip

nailed to the outside wall should be used in

con iunction with sill support angle brackets.

/i!

._Su'pport bracket

rVoodenstrip

5. Screw or nail cabinet to wooden frame using

shims if frame is oversized, to eliminate

distortion. Remember to maintain proper

slope as described in Step 3.

6. Install chassis into cabinet by following all

steps in Step 8of Window Mounting.

(continued)

OPTIONAL: Caulking and installation of trim on

interior war may be done. You can buy wood

fi'om your local lumber or hardware supply. On

the outside, caulk openings around top and sides

of cabinet, and all sides of wood sleeve to the

opening.

NOTE: See Step 7, Item 3 of Window Mounting

Instructions for bottom raft seal location.

Masonry Construction

1. Cut or build awail opening in the masonry

wall similar to the flame construction (refer to

Step 2of Thru-the-Wall Installation for a wall

thickness greater than 8-1/2").

,Secure cabinet in place using masonry nails, or

the right masonry anchor screws. (Another

way to do this is to build an in-between frame

of 2x4's (51 minx 102 ram) as shown in the

Step 2 Prepare Wall illustrations-- but make it

double framed on either side, and install

between masonry wall opening and cabinet.

Frame must be securely anchored to masonry

wal! opening.) This way gives very good

louver clearance on either side of cabinet.

3. Install a lintel to support masonry wall above

cabinet. Existing holes in cabinet can be used

and/or additional holes can be drilled to fasten

cabinet at various positions. Be sure that side

louver clearance is in accordance with Step 1

above.

.Install exterior cabinet support brackets as

shown in Step 2 of Thru-the-WaU Installation.

Caulk or flash ff needed, to provide a weather-

tight seal around top and sides of cabinet.

5. To complete installation, apply wood trim

molding around room side projection of

cabinet.

Instrucciones para instalaci6n

Para el A-Kit 22"

Por favor, lea TODAS las instrucciones antes de

instalar el aparato. Se recomienda que este

producto sea instalado por dos personas. Si

requiere un toma corriente nuevo, haga que se

1o instale un electricista califlcado, antes de

instalar la unidad. Vea el punto No. 5 de las

Instrucciones preliminares que aparecen a

continuaci6n.

SELLD DE LA HOJA

CERRADURA DE

_7.1URIDAD y TORNILL

DE CABEZA HEXA_4_L

DE 2/4" DE LARGO

Instrucciones preliminares

Proceda a hacer lo siguiente antes de empezar

ainstalar la unidad. Vea lasgr_cas que

aparecen abajo.

1. Examine el tamafio de la apertura de la SNSA._ DEL,A,co

ventana - las partes de montaje que (,ZOUmaDA)

acompaftan a la unidad de aire acondicionado

esrgn disefiadas para instalaci6n en una

ventana doble con soleras de madera. I.as

partes est£ndar son para una apertura de

ventana que mide 30" (711ram) como mlnimo,

y 42" (1067mm) de ancho mgximo. Cuando la

hoja de la ventana es_ abierta, el minimo debe

ser 19" (483mm). (FIG.l)

2. Examine las condiciones de la ventana -

todas las partes de madera de la ventana

deben estar en buenas condiciones ydeben

ser capaces de soportar firmemente los

torniUos clue se necesitan. Si este no es el caso,

haga las reparaciones necesarias antes de

instalar la unidad.

3. Examine sus vemtatms para tormenta.

Usted necesitara una luz de 1/2" (13ram)

debajo de la repisa de la ventana. Si el marco

no pea'mite la apertura requerida, agregue una

pieza de madera como se muestra en la FIG.2

o quite fa ventana para tormenta mientras se

instala la unidad de aire

acondicionado. (continda) _ HOJA

FIG, I'T

• MIN. i

19"MIN.

HARCO DE LA VENTA DE

TORMJENTA U OTRO

OBSTACULO

EMPAQUE

DE HULE

ESPUMA

ROLDANA PARA

ASEGURAR LA

CABEZA DEL

TORNILLD

RIEL DE SF.LLADD

DIE LA pARTE

INFERIDR DE LA

UNLOAD

ANGULO $UPE_OR

CON1

PERt/ODE:

PULGADA DE

CAIIEZA PLANA

HARCD

(DERECHA)

_3YO DE LA

VENTANA

ANGULAR SENC_LLO

FIG. 2

: 19"MIN.

1/2' MIN. !1 1/2"M_1

'J,gog¢&, gs

MARCO DE LA VEIqTANA DE

TORHENTA U DTRO OBST_ULD

309000904 (9704)

4. EXAMINE SI EXISTE ALGO QUE

PODRiA BLOQUEAR IA CORRIENTE

DE AIRE -examine el krea del exterior

de la ventana, para ver si existen

arbustos, itrboles otoldos. En el

interior, est_ seguro que los muebles,

cortinas o persianas no interrumpen el

flujo apropiado de aire.

.Examine si exlste servido el_ctrico

disponible - el suministro de energla

el6ctrica debe coincidir con el clue aparece

en la placa del ndmero de serie de la unidad

(Vea la Guia del propietario para saber d6nde

es_ la placa,) El cord6n eMctrico mide 48" de

largo. Est6 seguro de que existe un toma

corriente cercano, iEs mejor no usar

cordones de extensi6n!

Todos los modelos tienen un conector de

tres espigas para servicio apropiado ypuesta

a tierra posit.Do de seguridad. No cambie el

conector por ninguna raz6n. No use un

conector adaptador. Si su tomacorriente de

pared actual no es del tipo necesario, [lame a

un electricista calificado para que haga el

cambio.

Evite los riesgos de

mcendtoso choques el_ctncos. No useun

cord6n de extension o un adaptador para

ef tomacorriente. No saqoe ninguna

espiga del enchufe del cord6n el*ctrico.

Toma¢orriente

puestoa tierra

ninguna

CordOn eMctrico puesto

atierra con enchufe de

3espigas.

6. Desempaque cuidadosamente el

acondicionador de aire - quite todo el

material de empaque. Proteja el piso o la

alfombra para que no se darien. Dos

personas deben instalar la unidad.

Herramientas que se necesitan

"] un desarmador grande de cabeza plana

"_ un desarmador Phillips No, 2

_/ Cinta de medir

Llave ajustable o alicate

x! Cuchilla con filo

_/ un Hpiz

Cerrajeria (en bolsa plgstica)

Roldana para Cantidad

asegumr la

cabeza del 2

tomillo

TornilIo de

cabeza

hexagonal de 3

3-4" de largo

Cerradura de

seguridad 1

_( Tomillodel-

2" de largo y 4deedu

contr_tuet'ca

@Pemo de cabeza

plana de 3-4" de 2deciu

largo y

ConU_tuerca

sencillo para la 2

solera

Tomillos para

el angular

superior lateral 12

de retenci6n

Tomillo

retcnedor del 1

frente

This manual suits for next models

Table of contents

Languages:

Other Kenmore Air Conditioner manuals

Kenmore

Kenmore 66121615 User manual

Kenmore

Kenmore 25376250410 User manual

Kenmore

Kenmore 253.79184 User manual

Kenmore

Kenmore 580.75124 User manual

Kenmore

Kenmore 408.72012 User manual

Kenmore

Kenmore 580.71056 User manual

Kenmore

Kenmore 253.70062 User manual

Kenmore

Kenmore 580.75085 User manual

Kenmore

Kenmore 35760 User manual

Kenmore

Kenmore 580.74054 User manual

Kenmore

Kenmore 75063 6,000 User manual

Kenmore

Kenmore Kenmore 580.75051 User manual

Kenmore

Kenmore 253-35568 User manual

Kenmore

Kenmore 25371123011 User manual

Kenmore

Kenmore 580.75050 User manual

Kenmore

Kenmore 25378066890 User manual

Kenmore

Kenmore 580.75119 User manual

Kenmore

Kenmore 408.72012 User manual

Kenmore

Kenmore 580.75100 User manual

Kenmore

Kenmore 580.74259 User manual

Kenmore

Kenmore 580.74055 User manual

Kenmore

Kenmore 580.74093 User manual

Kenmore

Kenmore 580.76081 User manual

Kenmore

Kenmore 405.84086 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual