JVC TK-C215VP12 User manual
DOME CAMERA
TK-C215VP4
TK-C215VP12
INSTALLATION PRECAUTIONS
LST0474-001B
To installation contractor
: Be sure to read the followings beforehand for proper installa-
tion. Pass the manual to user after reading.
To user
: Please be sure to keep together with the instruction manual
after reading.
TK-C215VP4_JP.book Page 1 Wednesday, September 20, 2006 6:02 PM
Precautions regarding fall prevention
䡵Mounting screws for the base
Be sure to use M4 screw.
䡵Mounting the fall prevention wire
Note:
●Pay attention to the length, strength, routing
and material (insulation properties) of the fall
prevention wire used.
●The internal diameter of the rounded portion
on the camera unit to which the fall
prevention wire is to be mounted shall be at
least R4.1 mm and not larger than R6.5 mm,
and its external diameter shall not be larger
than R12 mm.
●When mounting the fall prevention wire to the
base, be sure to use the M4 screws mounted
on the base.
䡵Handling camera
Note:
●When mounting the base to the ceiling, or
when connecting the cable of the camera
unit, pay enough attention to the fall of each
part.
Safety Precautions
warning
Mounting to a firm place.
When mounting this unit to the ceiling or wall,
mount it to a secure location where it can
support the mass of this unit. When mounting
to an insecure location, make sure to carry out
reinforcement of the ceiling or wall before
installation.
The camera unit may fall if the mounting screw
or piping is not properly tightened. Ensure that
the screws and nuts are properly tightened.
Mounting the fall prevention wire
Connect the fall prevention wire to prevent this
unit from falling accidentally. The camera unit
may fall if this wire is not connected.
8mm
2mm
Fall Prevention
Wire
Base
R4 mm screw
M4 screw
(Attached to the base
)
TK-C215VP4_JP.book Page 2 Wednesday, September 20, 2006 6:02 PM
Precautions regarding water-proof and
dust-proof
䡵Fill the hole with sealing material
Fill the piping hole as well as the 2 mounting
holes mounted with screws using a sealing
material.
Memo:
●Use GE silicon or its equivalents as the
sealing material.
Note:
●If the piping hole and the 2 mounting holes
mounted with screws are not filled with
sealing material completely, water or vapor
may enter the holes causing the lens and
dome cover to fog. Make sure that these
holes are completely filled.
䡵Inserting the silica gel supplied
Take out the silica gel from the aluminum
package, insert it into the silica gel insertion
space of the camera unit and fasten using the
lug plate.
Memo:
●During reconnection or re-installation after
repair or maintenance, make sure to replace
the silica gel with a new one.
●Consult your nearby JVC’s dealer on the
replacement procedures.
Serial number of part to be replaced: Use a
LW40500-001A silica gel.
Note:
●When mounting is performed on a rainy day,
make sure that rain water does not enter this
unit.
●Make sure to use the silica gel supplied.
Failure to do so may cause the camera lens
and dome cover to fog.
●If the angle of view is not adjusted
immediately after mounting the camera,
insert the silica gel after adjustment is
completed. The silica gel loses its effect if it is
exposed to the air for a prolonged period of
time.
Precautions for proper
installation
Sealing Material
Silica Gel Insertion
Space
Silica Gel
Lug Plate
TK-C215VP4_JP.book Page 3 Wednesday, September 20, 2006 6:02 PM
Precautions regarding water-proof and
dust-proof (continued)
䡵Precautions when mounting the
dome cover
●Make sure that the dome cover is firmly
fastened.
Otherwise, the humidity level may rise, which
may result in fogging and even falling of the
cover.
●Ensure that the fall prevention wire of the
dome cover is not caught in the space
between the dome cover and base. Failing to
do so may cause the dust-proof and water-
proof features to malfunction.
䡵Binding the sealing tape.
(When mounting the camera using the pipe)
Bind at least 2 layers of the sealing tape to the
joint of the pipe (point where the thread of the
piping hole coincides with the screw hole of the
pipe).
䡵Dust-proof performance
䢇Although this unit is IP66-compliant, water-
proof under all kinds of environment is not
guaranteed.
Precautions for proper
installation (continued)
Sealing Tape
12 mm(15/32 inch)
and below
© 2006 Victor Company of Japan, Limited LST0474-001B
TK-C215VP4_JP.book Page 4 Wednesday, September 20, 2006 6:02 PM
Other manuals for TK-C215VP12
1
This manual suits for next models
1
Table of contents
Other JVC Security Camera manuals
JVC
JVC VN-V686BU - Network Camera - Pan User manual
JVC
JVC TK-C700U - Color Cctv Camera User manual
JVC
JVC DZ-VCA1U Installation guide
JVC
JVC VN-H657WPBU User manual
JVC
JVC VN-V225VPU User manual
JVC
JVC Super LoLux HD VN-H157WPU User manual
JVC
JVC TK-C1460BE User manual
JVC
JVC TK-C205VPU(A) User manual
JVC
JVC VN-C205 User manual
JVC
JVC TK-C1460BE User manual
JVC
JVC TK-C1480E User manual
JVC
JVC VN-C20U - Network Camera Manual
JVC
JVC VN-V225VPU User manual
JVC
JVC V.NETWORKS VN-C625 User manual
JVC
JVC V.Networks VN-C2U User manual
JVC
JVC 1/3" CCD TK-C920U(A) User manual
JVC
JVC TK-C2201WPU - Analog Mini-dome -- Ip66 User manual
JVC
JVC TK-C205VP User manual
JVC
JVC VN-V686U User guide
JVC
JVC SuperLoLux TK-C9200U User manual
