JG special products SPEEDSTAR 3000 Instructions for use
April
2012
JG special products GmbH
Maintenance Tasks
SPEEDSTAR 3000
JG special products GmbH Seite | 1
Table of Contents
1. Cleaning material 3
2. Removing guide plates 3
3. Removing CIS-sensor 5
3.1 Removing CIS-guide plates 7
4. Select cleaning programms 7
4.1 Cleaning commands 7
5. Removing glued labels 11
6. Standard maintenance 11
7. Daily maintenance tasks 13
8. Bi-weekly maintenance tasks 16
9. Monthly maintenance tastks 19
10. Annual maintenance tasks 26
JG special products GmbH Seite | 2
Copyright statement
© 2012 JG special products GmbH.
This document, attachments, and information contained herein are the confidential and
proprietary property of JG special products GmbH. and their suppliers. As such, this
document, attached files, and information contained herein are subject to all nondisclosure
and proprietary information agreements currently in effect with your organization. Copies of
this document, any portion of this document, or attachments may not be transmitted or
disclosed to any third party without the prior written permission of JG special products
Gmbh.
© 2012 JG special products GmbH.
All content is the confidential property of, or licensed to, JG special products GmbH. (“JG
special products GmbH,” “we,” or “us”) and is protected under German and Foreign
copyright, trademark and other intellectual property laws.
The following statements will be included in the Appendix:
Warranty
Safety precautions
Regulatory information
Environmental policy and information
Recycling
JG special products GmbH Seite | 3
1. Cleaning material
For the cleaning of the guide rolls and the guide plates a cotton cloth is most appropriate.
You can also use other cloths with a fine surface structure.
Please use label remover for removing effortlessly the labels from the guide rolls and the
guide plates. You can choose yourself the cleaner.
For cleaning the print head and the CIS sensor a microfibre cloth is most useful. You can
also use other cloths but with a fine, fuzz-free texture. For cleaning the paper sensor,
cotton sticks are most appropriate.
The cleaning should be carried out only with distilled water and no other detergents or
liquids.
2. Removing guide plates
First remove the two screws of the guide plates with the Philips screwdriver. Afterwards
both screws of the holding frame of the CIS sensor have to be removed.
Remove
JG special products GmbH Seite | 4
At this moment, the two screws do not have to be removed. You can now remove the
guide plates by taking it out diagonally upwards.
Release
JG special products GmbH Seite | 5
The guide plates are then to be cleaned with the cloth and the label remover until labels
and rests of glue are removed.
3. Removing CIS-sensor
The CIS sensor is a very sensitive component and should therefore be handled carefully.
For this reason you should not use any tools in order to protect the sensor.
Lift the sensor out of the guide plates. Please watch the connecting cables of the sensor.
They are not to be bended or squashed.
JG special products GmbH Seite | 6
Remove carefully the connecting cables of the CIS sensor. Do not rip or tear!
Afterwards you can clean the bottom side of the sensor. The cleaning is to be carried out
only with distilled water and a fine microfiber cloth, otherwise the protective glass can be
scratched.
JG special products GmbH Seite | 7
3.1 Removing CIS guide plates
After cleaning the CIS-sensor you can put it carefully aside as to the protective glass lies
up.
Remove the 4 screws.
Please be careful at this action.
The ink tubes are not to be squashed or cutted.
Afterwards remove carefully backwards the Plastic frame from the printer.
The Plastic frame is to be cleaned with the cloth and the label remover until there are no
more labels and adhesive rests.
4. Select cleaning programs
By wiping the print head, the colours in the print head are mixed. Therefore you have to
start manually the cleaning procedure of the printer.
Act as follows:
Remove
JG special products GmbH Seite | 8
In the main picture use the button Maintenance
Click on the field Light clean
1.
2.
JG special products GmbH Seite | 9
A window appears showing the estimated cleaning time.
Confirm with OK.
4.1 Cleaning commands
With every cleaning of the print head ink is being used and the print head is being worn.
Therefore you should first start with the weakest cleaning command as the individual
functions are to be distinguished from each other in application.
After confirming the buttons a message with the needed time appears at all commands.
This can be carried out with YES for processing or NO for cancelling.
3.
Table of contents
