ITT Advantage 2.0 User manual
Industrial Process
Installation and Operation
Manual
Advantage® Actuator 2.0
Table of Contents
Introduction and Safety...................................................................................................................................................2
Safety message levels.........................................................................................................................................................2
User health and safety.......................................................................................................................................................2
Transportation and storage.............................................................................................................................................4
Handling and unpacking guidelines................................................................................................................................4
Storage, disposal, and return requirements...................................................................................................................4
Product Description..........................................................................................................................................................5
Actuator identification......................................................................................................................................................5
Bonnet description............................................................................................................................................................6
Valve diaphragm identification........................................................................................................................................7
Installation...........................................................................................................................................................................8
Precautions.........................................................................................................................................................................8
Install the valve and topworks.........................................................................................................................................8
Disassemble the valve.......................................................................................................................................................9
Replace the valve diaphragm.........................................................................................................................................10
Mount the topworks to the valve..................................................................................................................................12
Tighten the bonnet fasteners.........................................................................................................................................12
Fastener torque table for valve body to topworks..................................................................................................13
Actuator operating pressure..........................................................................................................................................13
Set the adjustable opening stop.....................................................................................................................................13
Table of Contents
Advantage® Actuator 2.0 Installation and Operation Manual 1
Introduction and Safety
Safety message levels
Definitions
Safety message level Indication
DANGER:
A hazardous situation which, if not avoided, will
result in death or serious injury
WARNING:
A hazardous situation which, if not avoided, could
result in death or serious injury
CAUTION:
A hazardous situation which, if not avoided, could
result in minor or moderate injury
Electrical Hazard:
The possibility of electrical risks if instructions are
not followed in a proper manner
NOTICE: • A potential situation which, if not avoided,
could result in an undesirable result or state
• A practice not related to personal injury
User health and safety
General precautions
This product is designed and manufactured using good workmanship and materials, and meets all
applicable industry standards. This product should be used only as recommended by an ITT engineer.
WARNING:
• Misapplication of the valve can result in injury or property damage. Select valves and valve
components of the proper materials and make sure that they are consistent with your specific
performance requirements. Incorrect application of this product includes but is not limited to:
• Exceeding the pressure or temperature rating
• Failing to maintain this product according to the recommendations
• Using this product to handle caustic or hazardous substances that it is not designed to handle
Qualifications and training
The personnel responsible for the assembly, operation, inspection, and maintenance of the valve must be
appropriately qualified. The operating company must do the following tasks:
• Define the responsibilities and competency of all personnel handling this equipment.
• Provide instruction and training.
• Ensure that the contents of the operating instructions have been fully understood by the personnel.
Introduction and Safety
2 Advantage® Actuator 2.0 Installation and Operation Manual
Instruction and training can be carried out by either ITT or the reseller of the valve by order of the
operating company.
Non-compliance risks
Failure to comply with all safety precautions can result in the following conditions:
• Death or serious injury due to electrical, mechanical, and chemical influences
• Environmental damage due to the leakage of dangerous materials
• Product damage
• Property damage
• Loss of all claims for damages
Operational safety precautions
Be aware of these safety precautions when operating this product:
• Do not leave hot or cold components of the product unsecured against contact if they are a source of
danger.
• Do not remove the contact guard for moving parts when the product is in operation. Never operate
the product without the contact guard installed.
• Do not hang items from the product. Any accessories must be firmly or permanently attached.
• Do not use the product as a step or hand hold.
• Do not paint over the identification tag, warnings, notices, or other identification marks associated
with the product.
Maintenance safety precautions
Be aware of these safety precautions when performing maintenance on this product:
• You must decontaminate the product if it has been exposed to harmful substances such as caustic
chemicals.
• You must immediately fit or reactivate all safety and protective equipment upon completion of work.
Use of unauthorized parts
Reconstruction or modification of the product is only permissible after consultation with ITT. Genuine
spare parts and accessories authorized by ITT serve to maintain safety. Use of non-genuine ITT parts can
annul liability of the manufacturer for the consequences. ITT parts are not to be used in conjunction with
products not supplied by ITT as this improper use can annul all liability for the consequences.
Unacceptable modes of operation
The operational reliability of this product is only guaranteed when it is used as designated. The operating
limits given on the identification tag and in the data sheet may not be exceeded under any circumstances. If
the identification tag is missing or worn, contact ITT for specific instructions.
Introduction and Safety
Advantage® Actuator 2.0 Installation and Operation Manual 3
Transportation and storage
Handling and unpacking guidelines
CAUTION:
Always observe the applicable standards and regulations regarding the prevention of accidents when
handling the product.
Handling guidelines
Follow these guidelines when handling the product to prevent damage:
• Use care when handling the product.
• Leave protective caps and covers on the product until installation.
Unpacking guidelines
Follow these guidelines when unpacking the product:
1. Inspect the package for damaged or missing items upon delivery.
2. Note any damaged or missing items on the receipt and freight bill.
3. If anything is out of order, file a claim with the shipping company.
Storage, disposal, and return requirements
Storage
If you are not immediately installing the product after delivery, store it as follows:
• Store the product in a dry room that maintains a constant temperature.
• Make sure that the products are not stacked on top of one another.
Disposal
Dispose of this product and associated components in compliance with federal, state, and local regulations.
Return
Ensure these requirements are met before you return a product to ITT:
• Contact ITT for specific instructions on how to return the product.
• Clean the valve of all hazardous material.
• Complete a Material Safety Data Sheet or Process Data Sheet for any process fluid that could remain
on the valve.
• Obtain a Return Material Authorization from the factory.
Transportation and storage
4 Advantage® Actuator 2.0 Installation and Operation Manual
Product Description
Actuator identification
Design Overview
The actuator is a spring or double acting pneumatic actuator.
To determine if you have an Advantage actuator or an Advantage actuator 2.0 locate the spindle
compressor connection and determine if you have a pin or t-slot connection.
Figure 1: Pin connection for Advantage
actuator
Figure 2: T-slot Connection for Advantage
actuator 2.0
Model number
The actuator model number is located on the ITT identification tag. The model number is a four digit
number defining the actuator as follows.
Table 1: Actuator
Code Description
B Advantage actuator 2.0
Table 2: Mode of operation
Code Description
1 Fail open (spring to open, air to close) (direct acting)
2 Fail close (spring to close, air to open) (reverse
acting)
3 Double acting (air to open, air to close)
Table 3: Actuator series
Code1Actuator series2
03, 04 3
05, 06 5
08, 09 8
15, 16, 17 16
Table 4: Examples
Model number Description
B308 Advantage actuator 2.0, double acting, series 8
B215 Advantage actuator 2.0, fail close, series 16 with a 15
spring set
1For fail close actuators, codes are specific spring combinations.
2Series number equates to diaphragm effective area.
Product Description
Advantage® Actuator 2.0 Installation and Operation Manual 5
Identification tag
Line Description
1 Valve serial number
2 Valve size and model number
3 Valve diaphragm type
4 Maximum recommended actuation pressure
Bonnet description
Non-Sealed bonnet
The non-sealed bonnet has a weep hole that permits leakage of the process fluid if the diaphragm
ruptures.
Sealed bonnet
The sealed bonnet uses a special “V-notch” vent plug, which permits diaphragm inspection.
Figure 3: Weep hole and V-notch vent plug
Bonnet
weep hole
V-notch vent plug
(Sealed bonnet only)
Product Description
6 Advantage® Actuator 2.0 Installation and Operation Manual
Valve diaphragm identification
Diaphragm tab codes
All diaphragm materials and physical properties are batch traceable via permanent codes molded into the
diaphragm tabs. The molding date, grade of diaphragm, and valve size provide traceability to original batch
records.
Supplier code
Date code
Figure 4: Elastomer diaphragm front
Grade of
diaphragm
Valve size
Figure 5: Elastomer diaphragm back
Date code
Material code
Figure 6: PTFE diaphragm
Product Description
Advantage® Actuator 2.0 Installation and Operation Manual 7
Installation
Precautions
WARNING:
• All procedures must be performed by qualified personnel.
• When the process fluid is hazardous, thermal (hot or cold), or corrosive, take extra precautions.
Employ the appropriate safety devices and be prepared to control a process media leak.
• Always wear protective clothing and equipment to safeguard the eyes, face, hands, skin, and lungs
from the particular fluid in the line.
CAUTION:
• Disconnect electrical, pneumatic, and hydraulic power before servicing actuator or automation
components.
Install the valve and topworks
NOTICE:
The topworks size and configuration can limit the actual operating pressure. Consult the engineering
catalog for topworks sizing. Consult the factory or engineering catalog for vacuum operation.
Consider the following information before installing the actuator:
• The series 3, 5, 8, or 16 stainless steel bonnet Advantage actuator 2.0 can have the air inlets positioned
in any quadrant.
• The maximum valve operating pressure is 150 psig (10.34 bar). This pressure is applicable up to 100º
F (38º C). Valves at maximum pressure cannot be used at maximum temperatures.
1. If you have a weld end valve, then consider the following:
If you are welding ... Then ...
Manually Remove the topworks.
In line for schedule 10 or heavier pipe Remove the topworks.
In line for schedule 5 or lighter pipe
and tubing
You can weld with automatic equipment. Before you perform
the weld:
1. Do not remove the topworks.
2. Set the valve to the open position.
3. Properly purge the valve with an inert gas.
2. Install the valve.
If the valve is a ... Then ...
Dia-Flo diaphragm
valve
For horizontal piping systems to be drained through the valve, install the valve
spindle between 0º and 30º above horizontal. For vertical piping systems, no
specific orientation is required.
Installation
8 Advantage® Actuator 2.0 Installation and Operation Manual
If the valve is a ... Then ...
Pure-Flo diaphragm
valve
Install with the raised hash marks (castings) or small machined dots (forgings)
on the valve body at the 12 o’clock position to achieve the optimum drain angle.
3. Prior to pressurization (with the valve slightly open), tighten the bonnet fasteners.
For more information, see Tighten the bonnet fasteners in this manual.
4. Connect the air line.
Connection size is 1/8" NPT.
NOTICE:
Air line connections should be made with care so as not to damage the actuator covers.
5. Cycle the valve two to three times to verify smooth operation.
Disassemble the valve
1. Remove all line pressure.
2. Do you have a switch package?
• If yes: Proceed to step 3.
• If no: Proceed to step 5.
3. Do you have a fail open or double acting actuator?
• If yes: Proceed to step 4.
• If no: Proceed to step 5.
4. Do you have a series 33 actuator or adjustable opening stop?
• If yes: Remove the switch package.
• If no: Proceed to step 5.
5. If the actuator mode of operation is fail open or fail close, then load the actuator with air.
If the actuator mode of
operation is ...
Then ...
Fail open Load the air port in the upper cover of the actuator with sufficient air
to partially close the valve.
Fail close Load the air port in the bottom cover of the actuator with sufficient air
to partially open the valve.
6. Remove the bonnet fasteners.
7. Lift the topworks assembly from the valve body.
8. If the actuator mode of operation is fail open, then remove pressure load from the actuator.
9. Do you have a fail open or double acting actuator?
• If yes: Proceed to step 10.
• If no: Procedure is complete.
10. Do you have a series 33 actuator or adjustable opening stop?
• If yes: When the actuator is not on the valve body, do not allow the flats on the indicating spindle
to move below the upper cover spindle o-ring.
• If no: Procedure is complete.
Installation
Advantage® Actuator 2.0 Installation and Operation Manual 9
Table of contents
Other ITT Controllers manuals
ITT
ITT Lowara GENYO 16A / R15-25 User manual
ITT
ITT Hydrovar Installation and operating instructions
ITT
ITT Conoflow GB50 Series Instructions for use
ITT
ITT McDonnell & Miller PS-802 Series Installation and operating instructions
ITT
ITT Bell & Gossett ZoneTrol II Z-1 Manual
ITT
ITT GFH45 Instructions for use
ITT
ITT Engineered Valves Advantage 2.1 User manual
ITT
ITT Bell & Gossett ZoneTrol II Z-2 Manual
ITT
ITT Engineered Valves Advantage 2.1 8 Series User manual
ITT
ITT Conoflow GB 2800 Instructions for use
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
