ipf electronic OT330571 User manual
OT330571
operating range 30 … 200mm
plastic housing, compact design
setting by Teach-In
LED-display with setting control
small beam-spot because of PinPoint-LED
suppression of reciprocal influence
M8-connector,
4-pin
technical data
function background suppression
sensing range 30 … 200mm
adjustment range 30 … 200mm
operating voltage 10 … 30V DC
current consumption (without load) ≤ 45mA
output current (max. load) ≤ 100mA
output signal push-pull, no/nc
voltage drop ≤ 3V DC
response time / decay time ≤ 0.5ms
sampling frequency 1kHz
transmitting element (pulsed) LED, red-ligth, punctual
wavelength 630nm
short-circuit protection +
reverse polarity protection +
operating mode display LED green
display (signal) / setting control LED yellow
display (Teach-In) LED blue
interference suppression +
housing material plastic (ASA, MABS)
front screen material PMMA
degree of protection (EN60529) IP67
operating temperature
connection
-25 … +60°C
M8-connector, 4-pin
electric connection dimensional drawing light beam form
colors of LED
color independent diffuse reflection
sensor with background
suppression
●all dimensions in mm *transmitter axis
MANUAL •Subject to alteration! Version: June 2014
ipf electronic gmbh
•Rosmarter Allee 14 •58762 Altena
│
Tel +49 2351 9365-0 •Fax +49 2351 9365-19
│
Teach-in procedure for 1 point-teach (normal):
1. Aim the sensor to a reference surface e.g. a reflecting machinepart and make sure that
the blue Teach-LED ligths.
2. Touch the blue Teach-LED which is placed at the rear side of the housing with a
ferromagnetic tool for longer than 2 sec. but max. 4 sec., until all 3 LEDs start blinking
with a frequency of 1 HZ.
The blue Teach-LED flashes stronger once a tool is detected.
3. Touch the blue Teach-LED again for a short time with a ferromagnetic tool
in order to confirm the reference surface.
4. The standard configuration of the output is nc (normally closed).
It can be changed to no (normally open) by touching the blue LED again for a short
time within 4 sec. During this time all 3 LEDs are blinking slowly (1Hz).
5. As soon as only the blue LED lights, the Teach-in procedure is finished successfully.
Teach-in procedure for 2 point-teach (for objects close to background):
1. Aim the sensor to a reference surface e.g. a reflecting machinepart and make
sure that the blue Teach-LED ligths.
2. Touch the blue Teach-LED which is placed at the rear side of the housing
with a ferromagnetic tool for longer than 4 sec. but max. 6 sec., until all 3
LEDs start blinking with a frequency of 2Hz.
The blue Teach-LED flashes stronger once a tool is detected.
3. Touch the blue Teach-LED again for a short time with a ferromagnetic
tool in order to confirm the reference surface.
4. Remove the object from detection range and touch the blue Teach-LED
for a short time to teach the background.
5. As soon as only the blue LED lights, the Teach-in procedure is finished successfully.
If all LEDs blink fast (8Hz), the Teach-in procedure failed and has to be repeated.
MANUAL •Subject to alteration! Version: June 2014
ipf electronic gmbh
•Rosmarter Allee 14 •58762 Altena
│
Tel +49 2351 9365-0 •Fax +49 2351 9365-19
│
Note: The yellow LED indicates the detection of an object, but does not compulsory correspond to the switching output. The
Teach-In function is active for only 5min. after switching on power. The Teach-in procedure is operating with a
ferromagnetic tool as well as with 2 pin of M8-connector (white wire) by connection to operating voltage
(+Ub).
Reset to the factory settings
Touch the blue Teach-LED which is placed at the rear side oft he housing with a
ferromagnetic tool for 6 sec. until all 3 LEDs blink with a frequency of 4Hz and remove
the tool immediately. Following the blue Teach-LED should blink normally and the
sensor removes to factory settings.
connection: e.g.
VK200375
mounting bracket:
AY000118
Warning: Never use these devices in applications where the safety of a person depends on their functionality.
MANUAL •Subject to alteration! Version: June 2014
ipf electronic gmbh
•Rosmarter Allee 14 •58762 Altena
│
Tel +49 2351 9365-0 •Fax +49 2351 9365-19
│
Other ipf electronic Accessories manuals
ipf electronic
ipf electronic UT990934 User manual
ipf electronic
ipf electronic UT30C310 User manual
ipf electronic
ipf electronic UT139073 User manual
ipf electronic
ipf electronic UT360321 User manual
ipf electronic
ipf electronic OTQ80576 User manual
ipf electronic
ipf electronic UT36002B User manual
ipf electronic
ipf electronic UT139570 User manual
ipf electronic
ipf electronic OT059176 User manual
ipf electronic
ipf electronic UT300027 User manual
ipf electronic
ipf electronic DW34311 Series User manual
ipf electronic
ipf electronic OS15 Series User manual
ipf electronic
ipf electronic OT450521 User manual
ipf electronic
ipf electronic PT65 Series User manual
ipf electronic
ipf electronic UT189020 User manual
ipf electronic
ipf electronic UT129521 User manual
ipf electronic
ipf electronic OTR49175 User manual
ipf electronic
ipf electronic DW34312 Series User manual
ipf electronic
ipf electronic MW10015 Series User manual
ipf electronic
ipf electronic UT309023 User manual
ipf electronic
ipf electronic OTR49170 User manual
