InWin IW-RF100S User manual
IW-RF100S
User’s Manual
- 1 -
Table of Content
PREFACE P.2
SAFETY INFORMATION P.2
SPECIFICATIONS P.4
1Product Introduction
1.1 Box Content P.5
1.2 General Information P.6
1.2.1 Front Panel Controls and Indicators P.7
1.2.2 Rear Panel Configuration P.8
2Hardware Installation
2.1 Removing and Installing a Hard Drive P.9
2.1.1 Installing a Hard Drive P.9
2.1.2 Removing a Hard Drive P.9
2.2 Removing and Installing Top Cover P.10
2.3 Removing and Installing a Fan Module P.11
2.3.1 Removing a Fan Module P.11
2.3.2 Installing a Fan Module P.11
2.4 Removing and Installing a PSU Module P.12
2.4.1 Removing a PSU Module P.12
2.4.2 Installing a PSU Module P.13
2.5 Installing Slide Rail P.13
2.5.1 Identifying the slide Rail P.13
2.5.2 Take out the inner rail and slide the intermediate rail back P.13
2.5.3 Attach the inner rail to the chassis P.14
2.5.4 Mount the rail bracket to the cabinet P.14
2.5.5 Insert the chassis to the cabinet P.15
2.6 Installing Motherboard P.16
2.7 Connecting Cable P.17
3Backplane Introduction P.18
4Compatibility Lists P.20
5Q&A P.20
6Technical Support P.23
- 2 -
PREFACE
Thank you for choosing In Win IW-RF100S. This manual is written for system technicians who are
responsible for installation, troubleshooting, managing, and repairing this server chassis. This
document provides the overview of all the features of the chassis, a list of accessories or other
components you may need to finish the installation, troubleshooting methods, and instructions of
adding and removing components on the In Win IW- RF100S. For the latest version of this manual, you
may visit In Win’s server website to download the latest updated version.
SAFETY INFORMATION
To ensure safe and smooth operation of your In Win IW- RF100S, it is essential that you choose an
appropriate location for the system, provide an appropriate operating environment, and adequate
power for all components of the system. As you plan for installation, follow the guidelines below to
ensure that the system and its environment are safely and appropriately positioned for efficient
operation and service. Your system should be installed and serviced only by technically qualified
persons.
Environment selection: The system is designed to operate in a typical office environment. The location
should be a clean, dry, and free of airborne particles; a well-ventilated room and away from sources of
heat including direct sunlight and radiators; it should keep the sources of vibration or physical shock
away; the space should be with a properly grounded wall outlet, and with sufficient space to access the
power supply cords. The operation environment temperature should be around 0°C to 40°C (32°F to
104°F).
Heed safety instructions: Before working with In Win IPC/Storage server/ System products, we strongly
recommend you are using this guide as a reference and follow the safety instructions. The instructions
in this manual will help you ensure and maintain compliance with existing product certifications and
approvals. Follow the described, regulated components mentioned in this manual. Use of non UL
listing products or other regulatory did not approvals will make non-compliance with product
regulations in the region(s) in which the product is sold.
System power on/off: The power button DOES NOT totally turn off the system AC power. To remove
the power of system, you have to unplug the AC power cord from the outlet or system’s power supply
units. Make sure the power cord is unplugged before you open the chassis, add, or remove any
components.
- 3 -
Hazardous conditions, devices and cables: Hazardous electrical conditions usually present on power
supply units, and communication cables. Disconnect the power cord, and any other device which
attached to the server before opening the case. Otherwise, it will raise the risk of personal injury or
equipment damage.
Electrostatic discharge (ESD) and ESD protection: In most cases, ESD damages disk drives, electronic
boards, and other parts. We recommend that you work the installation only at an ESD free space. If the
situation does not allow, perform ESD protection actions by wearing an anti-static wrist strap attached
to ground any unpainted metal surface on your server during your operation.
Installing or removing jumpers: A jumper is a short length of conductor used to close, open or bypass
part of an electronic circuit. Jumpers on In Win backplane have a small tab on top that you can pick up
with your fingertips. Grip the jumper carefully, and plug the jumper to cover the jumper pins on the
backplane. Once you need to remove the jumper, gripping the jumper, and carefully pull out without
squeezing.
CAUTION
To avoid damage and prove your safety, please notice and following the terms listed below:
1. No to populate hard drives and turn on the power before the system is settle down.
2. Tighten or loosen all the screws, please use screw driver to operate.
3. Apply the correct screws which packed in the accessories box.
4. For your safety, it requires at least two persons lift, and place the unit.
5. Before mounting the unit to the cabinet, make sure the rail is installed correctly.
6. When installing and removing any module or parts, please operate by the handles.
- 4 -
SPECIFICATIONS
Model Name
IW-RF100S
Standard
EIA-RS310D
M/B Form Factor
MINI ITX (6.7“ x 6.7“)
Dimensions (D x W x H)
250 x 482.6 x 44 mm (9.8“ x 19” x 1.75”)
Drive Bay
Internal: 2.5" HDD x 2
3.5” HDD x 2 (Optional 2.5” HDD x 4)
Power Supply
Supports
▪Form Factor: Flex
▪Watt: Single 265W, or 315W
Indicator
Power Status, HDD, LAN Activity LEDs,
Front Control Panel
Power Switch, System Reset, USB 3.0 x 2
Cooling Fan
Supports 40 x 28 mm PWM Easy-Swap Fan x 2 (Max up to 3)
Material
Material: SGCC
Thickness: 1.0 mm
Slide Rail
20" Friction slide rail
- 5 -
1Product Introduction
1.1 Box Content
When you open the carton box of IW-RF100S, the contents should include:
- 6 -
1.2 General Information
When you open the top cover should be like the diagram shows bellow.
Top cover
Single module
power supply
PWM Fan x 2pcs
(max to 3 pcs)
Mini-ITX or ATX
M/B
Front Controls
and indicators
2 x 3.5” HDD tray
- 7 -
1.2.1 Front Panel Controls and Indicators
The front control panel includes USB IO ports and indicator LED lights.
No.
Name
Color
Status
Description
1
USB3.0 Connector
No LED function
USB devices connection
2
Power ON/OFF Button
Blue
Solid on
System is powered on
Off
System is not powered on
3
Power LED
No LED function
Press the button to activate Power LED
4
Hard Disk LED
Green
Blinking
System HDD accessing
5
Reset Button
No LED function
System reset
6
LAN LED
Amber
Blinking
Link between system and network
Off
No date transmission or receiving is occurring
3
2
4
6
5
1
- 8 -
1.2.2 Rear Panel Configuration
The rear side of IW-RF100S contains the space of AC power source, system IO, and an
expansion cards slot.
No.
Name
Description
1
Power Supply Window
This window is for installing single PSU, please reference In-Win
compatibility list to select the compatible models.
2
System I/O (depend on
M/B specification)
The I/O shield is different by brands and models, please contact In Win sales
for custom I/O shield service.
1
2
- 9 -
2Hardware Installation
2.1 Removing and Installing a Hard Drive
In Win IW-RF100S has two 3.5” disk cages, each supports installing a 3.5” hard drive, and stacking
a 2.5” drive.
2.1.1 Installing Hard Drive
Step 1: Loosen the thumb screw and pull backward to remove disk cage.
Step 2: Populate the 2.5” drive on the cage and fix it with 4 screws from the bottom. Stake a
3.5” hard drive on top, and screw it up with 4 screws from both sides.
Step 3: Put back the disk cage to the chassis, and push back the cage to the original position,
then tighten the thumb screw.
Step 1
Step 2
Step 3
Loosen the
thumb screw
a. Install 2.5” HDD x 1pcs
b. Install 3.5” HDD x 1pcs
b
a
Complete the HDD cage and
put it back to the chassis.
This manual suits for next models
1
Table of contents
Other InWin Chassis manuals
InWin
InWin 101 TUF GAMING User manual
InWin
InWin IW-RS316-02M User manual
InWin
InWin IW-RS104-07 User manual
InWin
InWin Chopin Pro User manual
InWin
InWin IW-RJ460-08 User manual
InWin
InWin IW-RS110-07 User manual
InWin
InWin IW-PE689 User manual
InWin
InWin C200 User manual
InWin
InWin Cobra IW-RS212-07 User manual
InWin
InWin 509 User manual
InWin
InWin Cobra IW-RS212-07 User manual
InWin
InWin 3RAMPD017600 User manual
InWin
InWin 805 User manual
InWin
InWin Explorer User manual
InWin
InWin IW-RJ448-05 User manual
InWin
InWin 305 User manual
InWin
InWin AIRFORCE User manual
InWin
InWin SIII-1065W User manual
InWin
InWin 703 User manual
InWin
InWin 703 User manual
