Intermec PR2 User manual

Product Name: Mobile Receipt Printer

Brand Name: Intermec

Model No: PR2/PR3

User’s Guide

Introduction

PR2/PR3 is a value entry performance mobile receipt printer. PR2 refers to a 2” Printer whereas PR3

corresponds to 3” Printer.

The differentiators of PR2/PR3 are:

a) Low system integration and management cost

b) Smallest Size

c) Lowest Weight

d) Fastest throughput

A PR3 printer is shown in Figure 1 (Top View)

Figure 1: A PR3 Printer (Top View)

The Front view of the printer is shown in Figure 2

Door Buttons

Tear Bar

LED Indicators

Power Button

Feed Button

LED Indicators

LED Name

LED Behavior and States

Ready-To-Work

Steady Blue = Printer is on and Ready-to-Work.

Flashing Blue: 50% duty cycle, 0.75 Hz = Printer

is on, but not ready to work or there is a critical

error.

Off = Printer is off or in deep sleep mode.

Connectivity

Flashes White: for 0.04 seconds for each packet

sent or received = Printer is communicating with

host (actively sending data)via USB, IrDA,

Bluetooth, or WiFi 802.11 radio.

Off = No data is being sent or received.

Battery

Off Charger

Off = Battery does not have a low charge.

Flashing Red: 25% duty cycle, 1 Hz = The

battery has a low charge.

On Charger

Steady Green = The printer is connected to

external power, and the battery is more than

95% charged.

Pulsing Green: (The output to the LED should be

driven with a pulse width modulated (PWM)

signal. The frequency used should be above the

human perception of any flicker. The difference

between PWM duty cycle changes should be

small enough so that there is no discernable

jump in output brightness. The duty cycle should

linearly change for 1.35 seconds to maximum

brightness, linearly change for 1.35 seconds to

minimum brightness and then remain off for 0.80

seconds. The resulting period of 3.50 seconds is

for a complete cycle from off to maximum

brightness and back to the off condition.) = The

printer is connected to external power and the

battery is charging and the battery is between

75% and 95% charged

Steady Red = the printer is connected to external

power and the battery is charging, and the

battery is between 0% and 75% charged

Flashing Amber at 50% duty cycle, 1 Hz = The

battery is out of charging temperature range.

Flashing Red at 50% duty cycle, 1 Hz = There is

a battery error.

Critical Error

Steady Red = Critical errors –cannot continue:

Door Open, Out of Paper, or Printhead is too hot

Off = No critical errors are present.

Magnetic Card Reader

Flashes Green 3 times in one second = Card

was read successfully

Flashes Red 1 time at 50% duty cycle, 1 Hz =

Card was read unsuccessfully

Off = Card reader is not being used.

Standard Communication Interfaces

There are various printer configurations based on the type of communication interfaces present in the

printer.

All configurations of the printer have USB communication.

Apart from USB, one of the following interfaces will be present

Bluetooth (FCC ID: EHA-INBT01; IC ID: 1223A-INBT01)

Wi-Fi

IrDA

Power Supply

The Printer is powered by a 2-cell battery pack with 8.4V, 1620mAh capacity.

Additionally, the battery is charged by using an external AC adapter which comes along with the printer

unit.

Print Test Page

To print a test page, press the feed button for a considerable duration (about 10 seconds) when the printer

is booting up.

Product operating temperature: -10 ~ 50 degree (discharge between -10 ~ 50 degree)

The battery charging mode to the operating temperature is only 40 degree.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Other manuals for PR2

This manual suits for next models

Table of contents

Other Intermec Printer manuals

Intermec

Intermec PB2 Series User manual

Intermec

Intermec EasyCoder 201II Manual

Intermec

Intermec EasyCoder PX4i User manual

Intermec

Intermec PK80 Series User manual

Intermec

Intermec PM4I User manual

Intermec

Intermec 6804DM Product manual

Intermec

Intermec EasyCoder 301 Manual

Intermec

Intermec EasyCoder PF4i User manual

Intermec

Intermec EasyCoder 601XP User manual

Intermec

Intermec EasyCoder 201II Manual

Intermec

Intermec EasyCoder PD41 User manual

Intermec

Intermec 6820 Series User manual

Intermec

Intermec 4400 User manual

Intermec

Intermec EasyCoder PX4i User manual

Intermec

Intermec PW50 User manual

Intermec

Intermec PB21 User manual

Intermec

Intermec EasyCoder 301 User manual

Intermec

Intermec 6820 Series User manual

Intermec

Intermec PM4I User manual

Intermec

Intermec EasyCoder PL4 User manual

Intermec

Intermec EasyCoder PD41 User manual

Intermec

Intermec PB41 User manual

Intermec

Intermec PB40A User manual

Intermec

Intermec EasyCoder 3400d Manual

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide