Interior technology Assunta RECTA User manual
Assembly Manual
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 2
Table of contents
Table of contents 2
Regulations 3
Panel preparation 4
Panel 1 5
Panel 2 6
Panel 3 7
Installation of guide rails 8
Installation of the lifting drive 9
Connection of the control unit 10
Installation of lower panel 12
Installation of the belts 14
Installation second / third panel 16
Adjustment of the guide blocks 18
Putting the system into operation 20
Installation of the fixed panel 22
Installation of the door aligners 24
Connection of the relay contacts 25
Error codes and user modes 26
Notes 27
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 3
Regulations
Liability
To ensure correct operation of the Assunta system, all steps in this manual must be followed carefully. VDS
BV can never be liable for the use of this manual and shall not be responsible for incorrectly installed sys-
tems.
Guidelines
It is essential that the panels are straight. Therefore, a maximum curvature or torsion of 1.5 mm applies to all
the panels of the system.
Copyright
All rights reserved. Nothing in this publication may be copied, stored in an automated data file or made pu-
blic, in any way or form, be it electronic, mechanical, by means of photocopies, recordings or any other me-
thod without prior written permission from the publisher. © 2023, VDS Verdonck Development & Systems.
This manual is self-published.
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 4
Mill the panels and, if applicable, the side
guide rails according to the drawings from
www.assunta.be. Also drill all the holes..
Panel preparation
Lower panel:
Optional second panel:
Optional third panel:
Fixed panel:
Guide rail:
True-to-scale drawings can be downloaded
from the website www.assunta.be.
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 5
Mount the frames (left and right) for the lower panel on the panel.
Panel 1
For surface mounted panels, provide an intermediate plate
with the correct thickness (Y- d) and the same hole pattern
as the panel. Or attach the intermediate plate BEFORE dril-
ling the panel.
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 6
Mount the frames (left and right) for the second panel on the panel..
Panel 2 (if applicable)
For surface mounted panels, provide an intermediate plate
with the correct thickness (Y- d) and the same hole pattern
as the panel. Or attach the intermediate plate BEFORE dril-
ling the panel.
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 7
Mount the frames (left and right) for the third panel on the panel..
Panel 3 (if applicable)
For surface mounted panels, provide an intermediate plate
with the correct thickness (Y- d) and the same hole pattern
as the panel. Or attach the intermediate plate BEFORE dril-
ling the panel.
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 8
Place the side guides in the side walls of you cupboard. If these were purchased, there is an excess of 35 mm
on the height. Cut these to size at the top.
Installation of the guide rails
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 9
The height dimension for the lower
bore is shown on the drawings availa-
ble at www.assunta.be. The side di-
mension is fixed relative to the side
guide.
Installation of the lifting drive
Place the lifting drives in the cabinet. If the side guides were purchased, the front Ø 3.5 mm holes are already pre-
drilled on the side guides.
Krommebeekstraat 46
8930 Menen, Belgium
T +32 (0)56 18 59 50
info@interiortechnology.be
www.interiortechnology.be
InteriorTechnology.be is the signboard of the activities of VDS bvba concerning interior automation.
Pag. 10
Place the control box in the cabinet (between the motors). Connect the power cable 220V and motor cables
to the control box. Optionally, also connect the remote control receiver and/or cable (Assunta or own) push
buttons.
Connection of the control unit
Power cable
Right-hand motor cable
Left-hand motor cable
RC receiver
Cable
Push buttons
Also connect the motor cables
on the motor side.
Cable
Push buttons
RC receiver
Left-hand motor cable
Right-hand motor cable Power cable
Table of contents
Other Interior technology Indoor Furnishing manuals
