INSTEON 2420M User manual

Indoor/Outdoor

INSTEON Motion Sensor Model #2420M

1. INTRODUCTION

The INSTEON Motion Sensor is an indoor/outdoor motion sensor that will

turn INSTEON controlled lights On and Off in response to movement

around your home. The sensor also contains a photocell, allowing you to

configure the unit to only turn your lights on at night. Pair the Motion Sensor

up with INSTEON software for almost limitless automation possibilities.

In this package you will find the Motion Sensor, a 9V battery, a swivel

mount, and 2 screws.

INSERT BATTERY

Use a small Philips head screwdriver to remove screw from battery

compartment on back of unit and remove cover. Attach the included 9 volt

battery. Do not replace compartment cover until instructed to do so later in

this manual. Wait 5 minutes for the circuit to stabilize. Then, to confirm unit

is functioning, tap the set button a couple of times while watching the front

of the unit. Each time you tap the Set button, a red LED behind the sensor

lens will flash. Don’t worry if the LED flashes when you are not tapping the

set button as it is simply indicating that motion is being detected.

(Close-up

of battery

compartment)

ACCESS POINTS

Motion Sensor requires at least one INSTEON Access Point (#2443)

product installed in your home. To confirm the Motion Sensor is within RF

range of your Access Point, have a friend watch the LED on the side of

your Access Point while you tap the set button on the Sensor (while holding

it where you plan to install it). Access Point’s LED will flash a couple times

every time you tap the set button if it is within range.

MOUNTING (See Locating Tips for Help)

1. Use the two small screws (included) to secure the swivel mounting

bracket at your desired location.

2. Slide Motion Sensor onto the swivel mounting bracket (sliding the unit

to the right) until you hear a click.

3. Aim Motion Sensor towards the area in which you wish to detect motion

(detection area).

4. Test by walking through the area, linked responders should turn on

when motion is sensed, and off 1 minute after last motion sensed.

Motion Sensor 9V

Battery Swivel

Mount 2- 3x18

Screws

3. SETUP

7. SETUP MODES

(

tional

)

SET JUMPERS

Jumpers are small plastic

“boxes” that act as a

switch. When mounted on

2 pins, the switch is “on”.

When mounted on 1 pin

(or missing), the switch is

“off”.

Jumper 1 – Sensitivity

To reduce Sensor’s

detection range (by

approximately 33%),

carefully remove the left-

most jumper, jumper 1

(from the single pin it is

mounted on) using a pair

of needle-nose pliers and

re-mount it on both pins.

4. SETUP INSTEON DEVICE CONTROL

LINKING TO INSTEON RESPONDERS

1. Press & hold the Set button on Motion Sensor for 5 seconds (until red

LED behind sensor lens begins steady blinking, you now have 4

minutes to complete step 2)

2. Press & hold set button1for 5 seconds on the INSTEON responder (e.g.

SwitchLinc) you would like the Motion Sensor to control (an LED may

blink and the connected load/bulb may flash)

3. Motion Sensor’s LED will stop blinking (if not try step 2 again)

4. Test by tapping the Motion Sensor’s set button. Each tap should

alternatively turn the device you linked (e.g. SwitchLinc) on and off.

(Motion Sensor’s LED will flash each time Set button is tapped)

5. Repeat this procedure for up to 32 responders you wish the Motion

Sensor to control.

1For Multi-button responders (e.g. KeypadLinc) tap the button you wish to

control before pressing & holding its set button.

6. ADJUST DETECTION ARE

AIMING & SENSITIVITY

1. Tap Motion Sensor’s set button until the linked responder(s) turn off

2. Within 10 seconds walk well out of detection area

3. Wait 20 seconds

4. Walk into and near your detection area. Your linked responders will

turn on (LED will flash upon initial motion, then once every 8 seconds

during motion)

a. If LED does not flash while you are moving within the

desired detection area, re-aim Sensor (usually means

pointing the Sensor “up”)

b. If LED flashes while you’re moving outside detection area

i. Aim Sensor to decrease range (usually means

aiming the Sensor “down”)

ii. If aiming sensor does not generate desired results

place jumper 1 on both pins (see section (Choose

Modes)

Tap the set button once, wait 10 seconds, and activate motion to

establish the new setting.

Jumper 2 – Disable LED

If you wish to disable the LED (will still operate during setup), mount

umper 2 on both pins. Tap the set button once, wait 10 seconds, and

activate motion to establish the new setting.

Jumper 3 – Night-Only Mode

If you wish to have the Sensor operate only when dark, mount jumper

3 on both pins. Tap the set button once, wait 10 seconds, and activate

motion to establish the new setting. Note: It takes 3.5 minutes to

detect the difference between day and night.

Jumper 4 – On-Only Mode

If you wish to disable the automatic countdown “Off”, mount jumper 4

on both pins and the Motion Sensor will only send “On” Tap the set

button once, wait 10 seconds, and activate motion to establish the

new setting.

Jumper 5 – Not Used

Set

Button

2. OPERATION

WHEN MOTION IS SENSED

1. When motion is sensed the Motion Sensor will send an “On”

command to up to 32 linked INSTEON responders and flash it’s LED

(unless it is daytime and unit is in night-only mode)

2. Sensor will begin a 1 minute countdown

3. Whenever motion is sensed during countdown, the countdown will be

reset to 1 minute to easily allow you to create “occupied” versus

unoccupied modes for your home.

4. When countdown expires the Sensor will send an “Off” command to

all linked responders (unless it is in on-only mode)

APPLICATIONS

1. Turn driveway or front step lights on when visitors approach

2. Have your fountain always on when you are around (and off when

you are away)

3. Save money by having HVAC and lighting automatically go into

energy savings mode when no one is around

5. MOUNT SENSOR

Jumper 1

Jumper 2

Jumper 3

Jumper 4

Jumper 5 (not used)

Set button

11. TROUBLESHOOTING

Symptom Resolution

Sensor won’t link to

responders Move a dual-band INSTEON device (e.g.

Access Point) closer to the Motion Sensor

Sensor won’t

control linked

responders

a) Make sure LED flashes to confirm it has

power and is sensing motion

b) Sensor is in night-only mode (and it is “day”)

c) Move a dual-band INSTEON device (e.g.

Access Point) closer to the Motion Sensor

d) Sensor is in its 1 minute countdown

LED flashing rapidly

after motion is

detected

Sensor did not receive an acknowledgement

from one or more linked devices. If this occurs

repeatedly you may need to move a dual-band

INSTEON device closer to the Sensor or you

may need to unlink a device which is no longer

in use in your home. If the INSTEON

responders are no longer available, you may

either use a software application or perform a

factory reset to remove the unwanted links.

LED not flashing

upon motion a) You may need to wait up to 8 seconds to

see the flash

b) Battery may need to be replaced

Not sensing motion a) Light detected and unit is in night-only mode

b) Motion Sensor Aimed too low

c) Temperature too high, or low (sensor needs

to be able to distinguish between what is

being sensed and its surroundings

d) See Locating Tips section

LED is double

flashing upon

motion

Low battery warning, replace with fresh battery

TECHNICAL SUPPORT

Skylink has contracted with Smarthome for support of the INSTEON

Motion Sensor. Customers should contact Smarthome for technical

support.

1. www.smarthome.com (product page, help desk, wiki, live chat)

2. email at support@smarthome.com

3. 1-800-SMARTHOME (800-762-7846)

8. REMOVE CONTROL OF INSTEON

UNLINKING FROM INSTEON RESPONDERS

1. Press & hold the Set button on Sensor for 5 seconds (until red LED

behind sensor lens begins blinking) and release

2. Press & hold the Set button on Sensor for an additional 5 seconds

(until the LED changes its blink pattern – it will now be on longer

than off)

3. Press & hold set button on INSTEON responder you would like to

unlink (until its LED blinks)

4. Motion Sensor’s LED will stop blinking (if not try step 3 again)

5. Test by tapping the Sensor’s set button. Taps should no longer

control the unlinked device. 14. CUSTOMER SERVICE

RETURN UNIT TO FACTORY SETTINGS

1. If possible, unlink from all responders before proceeding

2. Remove battery

3. Wait 15 seconds

4. While pressing & holding the Set button, re-attach the battery and

continue holding the Set button

5. After around 2 seconds, the LED will turn on and stay on for about 3

seconds. Once the LED turns off, release the Set button

12. FACTORY RESET

P/N. 2420M Rev.0101208

BEST LOCATIONS

Select a detector location that will provide the coverage required while

keeping in mind the following potential problems:

1. Reflective Surfaces - Do not aim the detector at reflective surfaces

such as mirrors or windows as this may distort the coverage pattern

or reflect sunlight directly onto the detector.

2. Air Flow - Avoid locations that are subject to direct high air flow such

as near an air duct outlet.

3. Moisture - Do not locate the detector near sources of steam or oil.

4. Sunlight - Do not aim the detector such that it will receive direct or

reflected (mirror) sunlight.

5. Obstruction - Do not limit the coverage by large objects within the

detection area such as plants or filing cabinets.

6. Pet Rejection - Do not aim the detector at a stairway which a pet has

access to and do not place furniture or objects higher than 3 ft / 0.9

m, which a pet can climb onto (e.g. a cat on a couch), closer than 6 ft

/1.8 m to the detector.

7. Fireplace - Do not locate the detector near a fireplace due to the light

and heat.

8. Snow or Ice – Snow or ice on the Fresnel lens may interfere with

Motion Sensor’s ability to detect motion.

9. Dirt – Dirt on the Fresnel lens may interfere with Motion Sensor’s

ability to detect motion.

10. LOCATING TIPS

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

WARNING

Changes or modifications to this unit voids the user’s authority to operate

this product and the manufacturer’s warranty

13. FCC

9. DETECTING ARE

Other INSTEON Security System manuals

INSTEON

INSTEON 2867-222 User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual