INSBUD IB-Tron 3100FAN-230V User manual

Electronic controller

IB–Tron 3100FAN-230V

for Air Handling Units (AHU)

THIS PRODUCT HAS THE MARK

AND HAS BEEN MANUFACTURED IN ACCORDANCE WITH ISO 9001 STANDARD

INSBUD ul. Niepodległości 16a

32-300 Olkusz

Polska

+48 503 166 906

e-mail: [email protected]

The manufacturer promotes development policy. The right to make changes and improvements to products

and instructions without prior notice is reserved!

The contents of this manual - texts and graphics are the property of the manufacturer or its subcontractors

and are protected by law.

manual version: 2.13.0

rmware version: 07

IB–Tron 3100FAN-230V

1 General information ............................................ 4

2 Properties ................................................... 4

3 Compatibility ................................................. 4

4 Technical data ................................................ 5

5 General thoughts .............................................. 5

6 Scope of delivery ............................................... 5

7 Principle of operation ........................................... 5

8 Controller design .............................................. 5

9 Dimensions .................................................. 6

10 Control panel of the controller ...................................... 6

11 LCD display ................................................. 7

12 Mounting ................................................... 8

13 Connection module ............................................. 9

14 FAN digital input .............................................. 10

15 Connection example ............................................ 10

16 Connection - Zehnder Basic, AERIS 350 i 450 STANDARD, ITHO Daalderop Aure Vent

D250 ...................................................... 11

17 Connection - replacement of LEGRAND ............................... 11

18 Connection - single phase fan with autotransformer ........................ 11

19 Connection - low voltage cable ...................................... 13

20 Installation notes .............................................. 14

21 Turning the controller on ......................................... 14

22 Conguration menu ............................................. 14

23 Conguration of outputs .......................................... 14

24 FAN input operation ............................................ 16

25 Temporary ventilation level ........................................ 16

26 Ventilation time ............................................... 17

27 Calibration .................................................. 17

28 Idle time .................................................... 17

29 Backlight time ................................................ 17

30 Backlight intensity ............................................. 17

31 Temperature unit .............................................. 18

32 Time format ................................................. 18

33 Filter change reminder ........................................... 18

34 Alarm states ................................................. 18

35 Firmware version .............................................. 18

36 Time and day of the week ......................................... 19

37 Factory settings ............................................... 19

38 Keypad lock .................................................. 19

39 Operating schedule - AUTO mode ................................... 19

40 Manual mode ................................................. 20

41 Semi-automatic mode ........................................... 21

42 Errors ..................................................... 21

43 Operation instructions ........................................... 21

44 Warranty terms and conditions ..................................... 21

WWW.INSBUD.NET

1General information

The IB–Tron 3100FAN-230V controller is an in-

dependent microprocessor regulator equipped with

a large liquid crystal LCD display, dedicated to ope-

rating air handling units (AHUs). The controller al-

lows to control 3 ventilation levels, for which the si-

gnal of switching on is a short circuit of the corre-

sponding lines to the common screw terminal.

The IB–Tron 3100FAN-230V controller allows to

regulate the ventilation level in the building based

on the programmed operating schedule or in manual

mode.

The IB–Tron 3100FAN-230V controllers save

energy costs by adjusting the ventilation level ac-

cording to needs. They thus contribute to environ-

mental protection and nancial savings. Can be wi-

dely used in hotels, oces, supermarkets, factories,

hospitals, residential homes and other buildings.

2Properties

Large backlit liquid crystal display showing

current ventilation level, temperature, set-

tings, day of the week and other information.

3 ventilation level to choose from.

Possibility of dening the time after which the

control panel switches to the lter change re-

minder mode (FILTER sign and acoustic si-

gnal).

Aesthetic and modern design.

Blue backlighting of the screen (backlighting

is activated when any button is pressed and

deactivated after some time of inactivity).

Easy, intuitive operation and programming.

Operating schedule of the process in a weekly

cycle with the accuracy of 1 minute and the

possibility of programming 4 time periods each

day.

Manual or automatic operating mode.

Temperature displayed with 0,1◦Cresolution.

Support for an additional digital input (three

operating modes to choose from).

Input for connecting a dirty lter signal from

AHU. When this input is shorted to the neu-

tral wire, the AHU will be turned o as a prio-

rity and an audible signal will sound.

Power supply from 230V mains with battery

backup of settings memory.

3Compatibility

The controller can be installed in place of manual

ventilation capacity switches, e.g:

Legrand SISTENA LIFE switch for ventila-

tion control 4 positions (0-1-2-3) 20A 250V

cat. 775958.

Zehnder ventilation switch SA 1-3V 4 positions

(0-1-2-3) 20A 250V cat. 775958.

The controller is compatible with the following

AHUs, among others:

Zehnder ComfoAir 300, 350, 450, 550 Basic

Tywent B3B, ZWC-B

StorkAir

NED AIR WTA HR 300, 400

Aeris 350 Standard VV

Mistral 300, 400, 250 ECONO

Mistral Mini 250 (AC 230 )

Vasco D300EII, D400II, D400EPII, D500II,

D500EII, DX4 E, DX5 E, DX6 E, X350, X425,

X500, D275EP III

Harmann Requra 20, 30, 40, 50

ITHO ECO4, HRU-3 BVH-004, Daalderop

Aure Vent D250

Mitsubishi LGH Lossnay

Dospel Luna

Orcon HRC EcoMax, MaxComfort 300, 400,

500

CLIMA Xtract ECO Plus Flat

Connection to sample AHUs later in this manual.

The controller can also be connected directly to the

fans:

single phase fans with „taps” controlling the

fan speed. Such a fan can be recognized by the

fact that it has PE, N wires and a few wires for

supplying the control phase, e.g. L1, L2, L3.

If the fan has only three wires, PE, N and L,

it means that the fan is not factory set for

speed change. In order to control such a fan,

additional electrical components are required,

e.g. inverter or autotransformer. An example

of connection with such a fan using an auto-

transformer is given later in this manual.

three-phase fans - the appropriate connection

should be designed depending on the fan used.

WWW.INSBUD.NET

4Technical data

Power supply: 230 V AC

Max. contact load:

3A/240V≈700 W

Ventilation level signal: short circuit with

COM1

Filter signal: short circuit with C2

Digital input: short circuit with C2

Number of ventilation levels: 3

Housing: ABS

Display: LCD (3,2”)

Control: Electronic

Ingress Protection Code: IP30

Settings memory: 36 months

Dimensions

(height ×width ×depth):

Control panel: 86 ×86 ×15 mm

Connection module: 62 ×45 ×27 mm

Energy consumption: <2W

Storage temp.: −5÷50◦C

Display temp.: −20 ÷140◦C

5General thoughts

The power supply should be turned o when

installing the controller. It is recommended to

entrust the installation of the controller to spe-

cialized personnel.

The controller is designed to work with devices

for which the active signal of switching on ven-

tilation levels is shorting the appropriate lines

to the common screw terminal (COM1).

The common screw terminal (COM1) and the

screw terminal of the individual ventilation le-

vels are isolated from the power supply - the-

se are the so called potential-free outputs (dry

contact).

6Scope of delivery

1x Controller

1x User Manual

7Principle of operation

When operating in automatic (operating schedule)

mode, at the beginning of each time periods the con-

troller switches on the ventilation level programmed

for that time period. It is possible to program 4 time

periods per day and to assign one of the available

ventilation level to each of them.

In manual mode, the user sets the ventilation level of

the air handling unit (AHU) by himself. The air han-

dling unit (AHU) works in this mode all the time,

until another ventilation level is set or the controller

is switched o.

All ventilation level outputs are disconnected from

the common screw terminal when the controller is

o.

8Controller design

The IB–Tron 3100FAN-230V controller consists

of two parts: main panel with LCD display with key-

pad and connection module with screw terminal for

connection of air handling unit, additional button,

lter signal and power supply.

Both modules are connected with each other by a at

cable, several centimeters long.

WWW.INSBUD.NET

9Dimensions

Control panel: Connection module:

10 Control panel of the controller

1- display.

2-Mbutton.

3-Pbutton.

4- temperature sensor.

5-UP button.

6-DOWN button.

7-FAN/OK button.

WWW.INSBUD.NET

11 LCD display

1- day of the week.

2- current ventilation level or information.

3- visible symbol means keypad lock.

4- temperature or setting value.

5- visible symbol means active ventilation mo-

de.

6- graphic representation of the current ven-

tilation level.

7- visible symbol means manual mode.

8- time.

9- time period.

10 - visible symbol means active semi-

automatic mode.

11 - graphic representation of the current ven-

tilation level. The animated fan rotates with

dierent speed or is not visible.

WWW.INSBUD.NET

12 Mounting

Separate the two parts of the main panel housing of

the controller. To do this, insert a at screwdriver

into the two slots visible in the bottom part of the

panel and lever the plastic catches.

After levering the catches, carefully separate the two

halves of the main panel. To avoid damaging the ca-

se, start from the lower part of the panel (from the

catches side).

After separating both parts, disconnect the at ca-

ble connecting the main panel with the connection

module by pulling the plug from the socket in the

front part of the panel.

The controller wiring, led to the electrical installa-

tion box, should be connected to appropriate termi-

nals of the controller, according to the manual.

Make the connections with power o.

Carefully lay down excess wires in the cable instal-

lation box, avoiding stresses that could break wires

from their terminals.

Place the connection module in the electrical instal-

lation box and screw the back part of the main panel

casing with two screws.

WWW.INSBUD.NET

Connect the at cable to the socket in the front part

of the main panel.

Connect the two parts of the controller, starting with

the catches at the top of the controller and ending

with the catches at the bottom.

For mounting, a rectangular mounting box of

80x80x50mm is recommended.

13 Connection module

L- 230 V AC power supply phase.

N- neutral wire 230 V AC.

HI - high, third ventilation level output. This

output is shorted to the common output when

the controller wants to turn on the 3rd venti-

lation level of the panel.

MED - medium, second ventilation level. This

output is shorted to the common output when

the controller wants to turn on the 2nd venti-

lation level of the panel.

LO - low, rst ventilation level. This output is

shorted to the common output when the con-

troller wants to turn on the 1st ventilation level

of the panel.

COM1 - common output of ventilation level..

SI - clogged lter signal input. When this in-

put is shorted to C2, the alarm is activated.

FAN - digital input. Shorting this input to C2

activates the input.

C2 - common input to SI and FAN.

The described situation of shorting HI, MED,

LO to COM1 refers to the situation when the

setting parameter CFG=4. A detailed descrip-

tion of other relay states for other CFG value

settings is described in the further part of the

manual.

Table of contents

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual