Ikelite DS-125 User manual

Digital Housing

i n s t r u c t i o n m a n u a l

6148.11 Canon SX110 IS

Thank you for your purchase of Ikelite equipment. Please read this

instruction manual completely before attempting to operate or dive with this

product.

Table of Contents

Product Registration........................................................P. 3

ackage Contents ......................................................P. 3

reparation ..................................................................P. 3

Initial Camera Setup........................................................P. 4

Parts of the Housing - Front View ..................................P. 5

Parts of the Housing - Back View ..................................P. 6

Opening the Housing ......................................................P. 7

Installing the Camera ......................................................P. 7

Closing the Housing ........................................................P. 8

Usage ..........................................................................P. 9

Turn Camera On..............................................................P. 9

Zoom Control ..................................................................P. 9

Using the Camera’s Built-in Flash ..................................P. 9

Diffuser and Deflector Installation and Use ....................P. 10

Entering the Water ..........................................................P. 11

Maintenance ................................................................P. 11

Lens Port ........................................................................P. 11

Lubricant..........................................................................P. 11

Housing Maintenance......................................................P. 12

Control Maintenance ......................................................P. 13

Specifications ............................................................P. 15

hoto Tips ..................................................................P. 15

Troubleshooting ........................................................P. 17

Replacement arts ....................................................P. 19

Recommended Accessories ....................................P. 19

Technical Support ....................................................P. 22

Limited Warranty ........................................................P. 22

Returning Products for Service ......................................P. 23

- Ikelite Digital Housing

- Silicone Lubricant

- Vinyl Port Cover

- Tray and Handle

ackage Contents

- Diffuser

- Deflector

- Extra Control Tips

roduct Registration

Please take a moment to fill out the online Ikelite roduct Registration

form at http://www.ikelite.com/forms/regForm.htm.

This product has been water pressure tested at the factory and is depth

rated to 200 ft. (60m). Thoroughly inspect and immerse the empty

housing completely in water before installing a camera. If any fogging

occurs or droplets of water enter the housing, do not install a camera.

Clean the housing main o-ring and retest to make sure that it is

watertight. Refer to the Troubleshooting section, page 17.

We suggest that you read this instruction booklet thoroughly before use

to have a full understanding of where each camera control is located,

and what function each control provides. Please read your camera

manual thoroughly to have a full understanding of each camera function.

If you are new to underwater photography, be sure to read the Photo

Tips section.

Due to the power required to operate the camera and LCD screen start

each dive with a fully charged camera battery.

reparation

Initial Camera Setup

- Insert a fully charged battery.

- Insert and format a memory card.

- Set camera date and time.

- Set Mode Dial to “Av” Aperture Priority.

- Set ISO to 80.

- Raise the camera flash to it’s open or “UP” position.

- Set Flash to forced “On .”

- In the Flash Settings Menu set Flash Mode to “Auto”, and

Red-Eye Corr. and Red-Eye Lamp to “Off.”

- Set White Balance to “Auto AWB.”

- Set Image Quality to “Superfine” and “L.”

- Set Metering to “Center Weighted Avg.”

- Set AF-assist Beam to “Off.”

- Set AF Frame to “Center.”

- Set AF Mode to “Single.”

- Set Review to 5 seconds.

- Set IS Mode to “Shoot Only.”

- In the Power Saving menu, set Auto Power Down to “Off” and Display

Off to “3 min.”

NOTE: Make sure that the camera flash is in the “up” or “raised” position

before closing your housing with the camera inside.

arts of the Housing - Front View

Shutter

Button

Lens

Port

Lens ort

External Tray Mounts

Lid Snap

Zoom

Dial

Mode

Dial

Housing Controls

1. Print/Share

2. Playback

3. Face Selector

4. Exposure Compensation

5. ISO/ ump,

6. Macro ,

arts of the Housing - Back View

7. FUNC./SET Button

8. Flash / Control Dial,

9. Continuous,

10. Display Button

11. Menu Button

Power Button

Canon

10x

OPTICAL

ZOOM

9.0

MEGA

PIXELS

SX110IS

PowerShot

Installing the Camera

1. Pull out on each housing control until it stops. This will get the controls

out of the way for installation of the camera.

2. Remove the Back from Housing and position camera on Mounting Tray.

3. Using a coin or screwdriver (preferred), secure the camera with the tray

mounting bolt which threads into the camera’s tripod socket - diagram A.

Do not cross thread or over tighten the mounting bolt or you may

damage the camera tripod socket threads.

4. RAISE the camera flash. This must be done before closing the

housing.

Opening the Housing

Lid Snaps have a Lock.

To open housing, push Lid Snap Lock

forward and lift as shown. Keep pressure

on the Lid Snap so it does not fly open

quickly. Some Lid Snaps have a lot of spring

tension once they go over center, so keep a firm grip on the Lid Snap.

Lid Snaps may be opened one at a time.

Push Forward

Lid Snap

Lock

Lift

Diagram A

Tray Mounting Bolt Mounting Tray

Housing Back

Lid Hook

O-ring

RAISE flash before

closing housing

Closing the Housing

1. Place housing face down in your lap or on flat surface.

2. Check to see that there is an o-ring on

the housing back and that it is clean

and in its proper location.

3. Guide the back into the housing front.

The o-ring should touch the housing all

the way around. There should be an

even gap all the way around between

the housing and the housing back.

4. Lift the lid snaps so they are extended

and place each lid snap into the

corresponding hook on the housing

back.

5. To close the housing, push down on

the lid snaps until they snap into place.

Lid snaps on opposite sides of the

housing should be closed at the same

time. Be sure they are down far

enough to engage the lock.

Double check - Once the housing is

closed, check the o-ring seal. Check

the gap between the housing back and

the housing. It should be even all the way around the housing.

Look through the clear plastic back at the o-ring. You should see a

darkened area where the o-ring is compressed against the housing

back. If you do not see an even black compression seal all the way

around the back, open the lid snaps, reseat the housing back and close

the lid snaps. Visually check the seal again.

Housing Back

O-ring

Housing Back

O-ring

Even gap on

all four sides

Using the Camera’s Built-in Flash

If you are shooting with the camera’s built-in flash and the camera lens

is set to the widest angle setting, you may need to zoom the lens slightly

or a dark area may appear in a lower corner of close-up photographs.

The lens port may block some of the light. Install the Diffuser and zoom

in slightly to eliminate any dark areas noted in your photographs (You

can test this above water). See Diffuser/Deflector Installation - page 10.

For the best results, we recommend using an external Ikelite Substrobe.

Zoom Control (lever type only)

After you have used the housing's

zoom control, it must be returned to the

center position to disengage. If the

housing zoom control is pushing the

zoom lever in either direction, you may

not be able to take a picture or access

other functions. This is because the

camera is receiving a signal from the

engaged zoom control.

Zoom Control

“Engaged”

Zoom Control

“Disengaged”

(Center Position)

Turn Camera On

Turn the camera on and operate each of the housing controls to get a

feel for using the camera in the housing.

You are now ready to shoot underwater photos!

Usage

The camera’s built-in flash CANNOT be used with optional Wide-Angle or

Accessory lenses.

Note: To shoot photographs closer than 2 feet (0.6m), we recommend using

an external strobe which can be positioned so nothing blocks the light

path between the strobe and the subject.

Diffuser Use

The diffuser should be installed when using the camera flash. When

shooting close-up photographs with the camera flash and at the camera

lens’s widest angle setting, the lens port on the housing can block a

portion of the light from the camera flash. This can result in a shadow in

a lower corner of the frame. Zoom the lens to eliminate the shadow (You

can test this above water).

Deflector Use

The deflector should be installed when using an Ikelite external strobe.

The deflector will block and redirect the camera’s flash to the AF35 slave

unit or EV-controller which controls the external strobe’s output.

Remove the diffuser before attempting to install the deflector.

Diffuser/Deflector material

Small hole

Cut-out

Section

A diffuser and deflector are

included with the housing. The

diffuser is white transparent plastic.

The deflector is also white but is

not transparent.

To install the diffuser or deflector,

push the “Cut-out” Section into the

port groove until it stops.

Note the Small Hole. To avoid

losing the diffuser or deflector, you

can attach a fishing line or string

that is secured around the back of

the housing port, to this hole.

Diffuser and Deflector Installation

Diffuser/Deflector properly

installed in port groove

Other manuals for DS-125

This manual suits for next models

Table of contents

Other Ikelite Camera Accessories manuals

Ikelite

Ikelite 200DLM/D User manual

Ikelite

Ikelite 6110.91 User manual

Ikelite

Ikelite 200DL User manual

Ikelite

Ikelite Olympus SP-350 Operating and maintenance manual

Ikelite

Ikelite SLR-DC Housing User manual

Ikelite

Ikelite DLM Dome Port with Zoom Extension .375 Quick start guide

Ikelite

Ikelite 6950.13 User manual

Ikelite

Ikelite SLR-DC Housing D700 User manual

Ikelite

Ikelite 6171.11 User manual

Ikelite

Ikelite 6060 Owner's manual

Ikelite

Ikelite DS51 User manual

Ikelite

Ikelite 6146.02 User manual

Ikelite

Ikelite SLR-DC 6855 User manual

Ikelite

Ikelite Canon PowerShot A700 User manual

Ikelite

Ikelite 47140 User manual

Ikelite

Ikelite 200DLM/A User manual

Ikelite

Ikelite 6147.95 User manual

Ikelite

Ikelite 6871.08 User manual

Ikelite

Ikelite DMC-ZS100 User manual

Ikelite

Ikelite Canon IXUS 950 IS User manual

Ikelite

Ikelite 4405 User manual

Ikelite

Ikelite POWERSHOT G11 User manual

Ikelite

Ikelite 6184.93 User manual

Ikelite

Ikelite 6243.35 Owner's manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions