Ikelite ST1K User manual

ST1K Sony Alpha TTL Kit

Item number 46040

Included in the Box

• TTL Kit with Hotshoe

• 1/16” Hex Key

Compatible Strobes

• Ikelite DS160, DS161

• Ikelite DS125 above serial number 5000

• Ikelite DS51

• Ikelite DS50 above serial number 70000

• Ikelite DS200 above serial number 7163

»SEA&SEA, INON, Nikonos, and Ikelite non-DS strobes

are not capable of powering the TTL Kit circuitry and

thus will not provide TTL operation with this kit. These

strobes may operate in manual power modes.

Installation and Use

Setting the TTL Circuitry Program

A small slide switch on the front of the TTL kit circuitry box

provides switching between manual or TTL operation.

Use “TTL” for TTL operation.

Use “MAN” for Manual operation with no preash. Strobe

power will need to be set manually.

If the strobe switch is in TTL mode, but the circuitry switch is

in the “MAN” Manual position, the strobe will re at full power

or at its selected power setting.

»The circuitry switch must be set prior to installation in

the housing. This setting cannot be changed while the

housing is underwater.

»Failure to make the correct selection will result in over-

or underexposure.

Removing the Hotshoe

Your housing came with a manual hotshoe installed. This

hotshoe must be removed prior to installing the TTL kit.

1. The hotshoe is attached by male connector to the female

socket of the bulkhead. Depress the tab on the male

connector.

2. Hold the female connector while gently pulling the male

connector out of its socket.

3. Store the manual hotshoe in a small sealed plastic bag

along with your spare parts.

4. The manual hotshoe may be reinstalled at a later time to

bypass TTL operation.

Installing the TTL Kit

1. Remove the camera mounting tray from the housing.

2. Using the included 1/16” Hex Key, loosen the Set Screw

on the left side of the Housing Mounting Tray.

Set Screw

1/16” Hex Key

Housing Mounting Tray

3. Looking into the housing from the back, orient the TTL

kit circuitry box with the hotshoe wire on your left and the

Male Connector end towards the front of the housing.

4. Slide the circuitry box into the center bottom of the

housing mounting tray. The male connector should come

out the front of the housing mounting tray near the port

opening.

5. Re-tighten the 1/16” set screw until it stops. DO NOT

over-tighten.

6. Line up the tab of the male connector with the female

connector coming out of the housing bulkhead and push

gently together. The tab will click into place when properly

connected.

7. Move the Male Connector Wire to the left and out of the

way of the Port Hole Opening.

Connecting Your Camera

1. Install your camera in the housing using the camera

mounting tray.

2. Orient the hotshoe so the “LOCK” insignia is facing you

and the wire is coming out of the back of the hotshoe.

3. Slide the hotshoe into the camera’s hotshoe mount.

4. Push the back of the hotshoe forward rmly until it stops.

This will ensure a good connection. Failure to push

the hotshoe far enough forward may result in lack of

TTL or failure to re strobes.

5. Rotate Hotshoe Locking Ring clockwise to tighen

hotshoe. DO NOT overtighten.

Setting your Strobes

Your Ikelite DS strobe must be set to TTL for TTL exposure

with this kit. Any ash EV compensation set in the camera

will be added to or subtracted from the ash exposure.

Use of manual power settings will provide manual ash

exposure.

Limited Warranty

This Ikelite product is warranted against any manufacturing

defects for a period of one (1) year from the original date

of purchase. To obtain warranty service, the product must

be returned to Ikelite postage paid. Ikelite will, at its sole

discretion, repair or replace such products, and will return

to customer postage paid. All other claims of any nature are

not covered. Except as mentioned above, no other warranty

expressed or implied applies to this Ikelite product.

46040_Sony-ST1K-Alpha-TTL-Kit_-1217

LOCK

Male Connector Tab

Male Connector Wire

Port Hole Opening

Turn set screw

clockwise to

secure electronics

Hotshoe Locking Ring

Female Connector

Table of contents

Other Ikelite Camera Accessories manuals

Ikelite

Ikelite Canon 6240.88 Owner's manual

Ikelite

Ikelite 6146.07 User manual

Ikelite

Ikelite PowerShot IXUS SD900 Ti User manual

Ikelite

Ikelite 2601.03 User manual

Ikelite

Ikelite 69740 User manual

Ikelite

Ikelite DSC-W200 User manual

Ikelite

Ikelite SLR-DC Housing User manual

Ikelite

Ikelite 6182.77 User manual

Ikelite

Ikelite 12 Owner's manual

Ikelite

Ikelite 6165.01 User manual

Ikelite

Ikelite Digital Housing User manual

Ikelite

Ikelite ALL User manual

Ikelite

Ikelite 6242.62 User manual

Ikelite

Ikelite 5509.33 User manual

Ikelite

Ikelite TG-7 User manual

Ikelite

Ikelite Canon 300D User manual

Ikelite

Ikelite 6182.78 User manual

Ikelite

Ikelite 6270.03 Owner's manual

Ikelite

Ikelite 6170.70 User manual

Ikelite

Ikelite Flex Arm User manual

Ikelite

Ikelite 46045 User manual

Ikelite

Ikelite F60fd Owner's manual

Ikelite

Ikelite SD870 IS Owner's manual

Ikelite

Ikelite 6242.20 Owner's manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions