ICT PRT-WX-DIN-1D User manual

PRT-WX-DIN-1D

Protege WX DIN Rail Single Door Controller

Installation Manual

The specifications and descriptions of products and services contained in this document were correct at the time

of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw

products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or

by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated

Control Technology Limited. Designed and manufactured by Integrated Control Technology Limited, Protege® and

the Protege® Logo are registered trademarks of Integrated Control Technology Limited. All other brand or product

names are trademarks or registered trademarks of their respective holders.

Last Published: 07-Oct-21 12:04 PM

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 2

Contents

Introduction 6

Single Door Controller Editions 6

Installation Requirements 7

Grounding Requirements 8

Safety Grounding 8

Earth Ground Connection 8

Mounting 10

Removal 10

Connections 11

Power Requirements 11

Auxiliary Outputs 13

Power over Ethernet (PoE) 13

Encrypted Module Network 14

Module Wiring 14

End of Line (EOL) Resistors 15

Backup Battery 15

Ethernet 10/100 Network Interface 16

Door Access Control 17

RS-485 Reader Locations 17

RS-485 Reader Connection (Entry Only) 17

RS-485 Reader Connection (Entry/Exit) 18

Door Contact Connection 19

Lock Output Connection 19

Programming the Onboard Reader 20

Inputs 21

EOL Resistor Value Options 21

Duplex Inputs 22

Trouble Inputs 23

Outputs 24

Configuration 25

Logging In for the First Time 25

Creating a Secure Password 25

Registering Your Controller 26

Set the Controller Time 26

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 3

Configuring the IP Address 27

Setting Up Integrated DDNS 28

Setting Up an HTTPS Connection 29

Connectivity Requirements for HTTPS 29

Self-Signed Certificate 31

Maintaining Your System 33

Signing In 33

Home Page 33

System Settings 34

Settings | Configuration 35

Settings | Options 35

Settings | Email 36

Settings | Custom Reader Format 37

Settings | Security Enhancement 38

Operators 38

Roles 39

Backing Up and Restoring Controller Programming 39

Upgrading Application Software and Module Firmware 40

Setting the IP Address from a Keypad 42

Temporarily Defaulting the IP Address 42

Defaulting a Controller 43

LED Indicators 45

Power Indicator 45

Status Indicator 45

Fault Indicator 45

PoE Power Indicator 45

Battery Indicator 46

Ethernet Link Indicator 46

Reader Data Indicators 46

Relay Indicator 46

Input Indicators 47

Mechanical Diagram 48

Mechanical Layout 49

Technical Specifications 50

New Zealand and Australia 52

Intruder Detection Maintenance Routine 52

Peripheral Devices 52

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 4

Testing Frequency 52

Recommended Routine Maintenance Procedures 53

European Standards 56

UK PD 6662:2017 and BS 8243 57

FCC Compliance Statements 58

Industry Canada Statement 59

Disclaimer and Warranty 60

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 5

Introduction

The Protege WX DIN Rail Single Door Controller is the central processing unit of the Protege WX System. It

communicates with all system modules, stores all configuration and transaction information, processes all system

communication, and reports alarms and system activity to a monitoring station or remote computer.

Flexible module network architecture allows large numbers of modules to be connected to the RS-485 module

network. Up to 250 modules can be connected to the Protege system in any combination to the network, over a

distance of up to 900M (3000ft). Further span can be achieved with the use of a network repeater module.

The current features of the controller include:

⦁Internal industry-standard 10/100 ethernet

⦁32 Bit advanced RISC processor with 2Gb total memory

⦁Encrypted module network using RS-485 communication

⦁NIST Certified AES 128, 192 and 256 Bit encryption

⦁Factory loaded HTTPScertificate

⦁OSDPconfigurable RS-485

⦁2 high security monitored inputs

⦁Industry standard DIN rail mounting

Single Door Controller Editions

There are two editions of the PRT-WX-DIN-1D Controller:

⦁The PRT-WX-DIN-1D can be supplied power from a 12V DC power supply connected to the N+ and N-

terminals.

⦁The PRT-WX-DIN-1D-POE can be supplied power from a 12V DC power supply connected to the N+ and N-

terminals OR from a power over ethernet (PoE) router via the onboard ethernet terminal.

The features specific to the PoE interface described in this manual are only relevant if using the appropriate

edition.

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 6

Installation Requirements

This equipment is to be installed in accordance with:

⦁The product installation instructions

⦁AS/NZS 2201.1 Intruder Alarm Systems

⦁The Local Authority Having Jurisdiction (AHJ)

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 7

Grounding Requirements

An effectively grounded product is one that is intentionally connected to earth ground through a ground

connection or connections of sufficiently low impedance and having sufficient current-carrying capacity to

prevent elevated voltages which may result in undue hazard to connected equipment or to persons.

Grounding of the Protege system is done for three basic reasons:

1. Safety

2. Component protection

3. Noise reduction

Safety Grounding

The object of safety grounding is to ensure that all metalwork is at the same ground (or earth) potential.

Impedance between the Protege system and the building scheme ground must conform to the requirements of

national and local industrial safety regulations or electrical codes. These will vary based on country, type of

distribution system and other factors. The integrity of all ground connections should be checked periodically.

General safety dictates that all metal parts are connected to earth with separate copper wire or wires of the

appropriate gauge.

Earth Ground Connection

The DIN rail enclosure and the DIN rail modules must be grounded to a suitable single-point earth ground

connection in the installation. A minimum 14AWG solid copper wire (or thicker, in accordance with local

authorities) shall be used from the Protege system's earth connection points.

The DIN rail enclosure includes an earth ground single-point link connection via the metallic enclosure. This single-

point link is the Protege system's earth ground. All modules that have earth ground connections and that are

installed in the same enclosure shall be connected to this single point. A single-point earth ground connection

avoids the creation of ground loops in the system and provides a single reference point to earth ground.

Reader Expander

Input Expander

Output Expander

Controller

Dialer’s Earth

Ground Connection

Power Supply

V-

DIN Rail Ground Connections (one or more cabinets installed in the same room)

DIN Rail Enclosure Additional DIN Rail Enclosure(s)

Module Network

(RS-485 N+, N-, NA, NB)

AC Mains Wiring

Earth Ground

Link Connection

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 8

Sector or Building #2Sector or Building #1 Sector or Building #3

Input Expander

Reader Expander

Input Expander

Output Expander

Power Supply

Controller

Dialer’s Earth

Ground Connection

V-

Earth Ground

Link Connection

DIN Rail Enclosure DIN Rail Enclosure DIN Rail Enclosure

Module Network (RS-485 N+, N-, NA and NB)

DIN Rail Ground Connections (multiple cabinets in different rooms, sectors, or buildings)

Note that the DIN rail enclosure earth terminal is connected to the power supply V- terminal.

There must be only one single earth grounding point per system.

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 9

Mounting

Protege DIN rail modules are designed to mount on standard DIN rail either in dedicated DIN cabinets or on

generic DIN rail mounting strip.

When installing a DIN rail module, ensure that there is adequate clearance around all sides of the device and that

air flow to the vents of the unit is not restricted. It is recommended that you install the module in a location that

will facilitate easy access for wiring. It is also recommended that the module is installed in an electrical room,

communication equipment room, secure cabinet, or in an accessible area of the ceiling.

1. Position the DIN rail module with the labeling in the correct orientation.

2. Hook the mounting tabs (opposite the tab clip) under the edge of the DIN rail.

3. Push the DIN rail module against the mount until the tab clips over the rail.

Removal

A Protege DIN rail module can be removed from the DIN rail mount using the following steps:

1. Insert a flat blade screwdriver into the hole in the module tab clip.

2. Lever the tab outwards and rotate the unit off the DIN rail mount.

PRT-WX-DIN-1D | Protege WX DIN Rail Single Door Controller | Installation Manual 10

Other manuals for PRT-WX-DIN-1D

Table of contents

Other ICT Controllers manuals

ICT

ICT Protege SE User manual

ICT

ICT Protege WX User manual

ICT

ICT Protege GX DIN Rail System Controller User manual

ICT

ICT PRT-CTRL-DIN-1D User manual

ICT

ICT PRT-CTRL-DIN User manual

ICT

ICT PRT-CTRL-DIN-IP User manual

ICT

ICT PRT-CTRL-DIN-1D User manual

ICT

ICT PRT-WX-DIN User manual

ICT

ICT Protege GX User manual

ICT

ICT Distribution 3 Series User manual

ICT

ICT Protege WX User manual

ICT

ICT PRT-WX-DIN User manual

ICT

ICT PRT-WX-DIN-1D User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual