Hunter Pro-C Operating instructions

PCC Series Controller

- and - Station

Indoor/Outdoor Models

Owner’s Manual and

Installation Instructions

PROC®

Residential and Light Commercial

Irrigation Controller

Table of Contents

Introduction and Installation

3Specications

4Pro-C Components

8Mounting the Controller to a Wall

9Connecting AC Power

10 Connecting Station Wires

11 Connecting the Battery

12 Connecting a Master Valve

13 Connecting a Pump Start Relay

14 Connecting a Hunter "Clik" Weather Sensor

16 Connecting a Hunter Remote

18 Connecting to the Hunter Solar Sync

Programming the Controller

19 Setting the Current Date and Time

20 Setting Program Start Times

21 Setting Station Run Times

22 Setting a Watering Schedule

24 Options for Running Your Irrigation System

26 Using the Pro-C to Operate Outdoor Lighting

Advanced Features

28 Set Pump/Master Valve Operation

28 Programmable Rain O

28 Setting Specic Days O

Hidden Features

29 Program Customization

29 Programmable Delay Between Stations

30 Programmable Sensor Override

31 Total Run Time Calculator

31 Easy Retrieve™Program Memory

32 Solar Sync Delay

33 Cycle and Soak

35 Hunter Quick Check

35 Clearing Controller’s Memory/Resetting Controller

35 Winterizing Your Irrigation System

Troubleshooting Guide

36 Problems, Causes and Solutions

Quick Check and Easy Retrieve are trademarks of Hunter Industries Inc.

Pro-C, Solar Sync, Rain-Clik, Freeze-Clik and SmartPort are registered trademarks of

Hunter Industries Inc.

Specications

Operating Specications

• Station Run Time: 1 minute to 6 hours on programs

A, B, and C

• Start Times: 4 per day, per program, for up to 12 daily starts

• Watering Schedule: 7-day calendar, interval watering up

to a 31-day interval or true odd or even day programming,

made possible by the 365-day clock/calendar

Electrical Specications

• Transformer Input: 120 VAC, 60 hz

(230 VAC, 50/60 hz International Use)

• Transformer Output: 24 VAC, 1 Amp

• Station Output: 24 VAC, 0.56 amps per station

• Maximum Output: 24 VAC, 0.84 amps

(includes Master Valve Circuit)

• Battery: 9-volt alkaline battery (not included) used

only for non-AC programming, the non-volatile memory

maintains program information

• Battery, front panel, internal CR2032 lithium for

real-time clock

Cabinet Dimensions

Height: 9" (23 cm)

Width: 10" (21.5 cm)

Depth: 4.5" (10.9 cm)

Outdoor cabinet is NEMA 3R, IP44 rated.

Default Settings

All stations are set to zero run time. This controller has a

non-volatile memory that retains all entered program data

even during power outages, without need for a battery.

Cleaning

Clean only with cloth dampened with mild soapy water.

Pro-C Components







   









 



Pro-C Components (continued)

①Main Display Indicates various times, values,

and programmed information

②Year Identies current calendar year

③Month Identies current calendar month

④Day Identies current calendar day

⑤Start Time Identies selected program

start time

⑥Program Selector Identies the program in use:

A, B, or C

⑦Station Number Identies currently selected

station number

⑧Run Time

Allows user to set each valve

station run time from 1 minute

to 4 hours

⑨Days of the Week Identies days of the week

to water or not water

⑩Odd/Even Watering Identies if odd or even

watering days are selected

⑪Interval Identies if interval watering

has been selected

⑫Seasonal Adjustment

Displays in increments of 5%,

the percentage of seasonal adjust

that has been selected

Running Sprinkler icon indicates when

watering is occurring

Rain Drop Indicates watering will occur on

selected day

Crossed Rain Drop Indicates watering will NOT occur

on selected day

ALCD Display

BControl Buttons and Switches

⑬jButton Increases the selected

ashing display

⑭kButton Decreases the selected

ashing display

⑮iButton

Advances the selected ashing

display to the next item, also use to

start a manual cycle

⑯hButton Returns selected ashing display to

the previous item

⑰nButton Selects programs A, B, and C;

also to start a test program

⑱Rain Sensor

Bypass Switch

Use to bypass weather “Clik-type”

sensors if one is installed

Pro-C Components (continued)





















D  







Pro-C Components (continued)

CControl Dial

①Run Normal dial position for

automatic operation

②Set Current Date/

Time Set current date and time

③Set Program

Start Times

Set 1 to 4 start times in each

program

④Set Station Run Times Set each station run time

⑤Set Days to Water

Select individual days to water,

odd, even or interval watering

schedule

⑥Set Pump Operation Turn pump or master valve

on or o for each station

⑦Seasonal Adjustment

Make global run time changes

without programming the

controller (from 5% to 300%)

⑧Solar Sync®Allows user to program settings

when using Solar Sync ET sensor

⑨Manual—Single

Station

Activates a one time watering of

a single station

⑩System O

Used to discontinue all programs

and stop all watering until the dial

is returned to the RUN position,

or to set the programmable rain

o feature

DWiring Compartment

①9-Volt Battery

An alkaline battery (not included) allows

programming of the controller without

AC power

②Reset Button This button will reset the controller.

All programmed data will remain intact

③Power Area Used to attach transformer, sensor wires,

and other systems to the controller

④Sensor Terminals Used to connect Hunter Solar Sync or

“Clik-type” sensors

⑤Transformer

A transformer is installed (Outdoor

models only, indoor models are supplied

with a plug-in transformer)

⑥Junction Box This box provides an area for connecting

primary AC power (Outdoor models only)

⑦SmartPort®

Input Terminals

Used to connect a SmartPort, which

enables Hunter remote controls

⑧Ground Lug For additional surge protection, connect

lug to earth ground

Mounting the Controller to a Wall

All necessary hardware is included for most installations.

1. Use the hole at the top of the controller as a reference and

secure a 1" (25 mm) screw into the wall. Note: Install screw

anchors if attaching to drywall or masonry wall.

2. Align controller with the screw and slide the keyhole

on top of the controller over the screw.

3. Secure controller in place by installing screws in the holes.

For PCC-601-A and PCC-1201-A: If the supply cord is damaged,

it must be replaced by the manufacturer or service agent or a

similarly qualified person in order to avoid hazard.

NOTE

The indoor Pro-C is not weather or water resistant, and

must be installed indoors or in a protected area. This device

is not intended for use by young children. Never let children

play with this device.

Outdoor model is water and weather resistant. Connecting

the outdoor Pro-C to the primary power should be done

by a licensed electrician following all local codes. Improper

installation could result in shock or fire hazard. This device

is not intended for use by young children. Never let children

play with this device.

Connecting AC Power

Indoor Cabinet

Route transformer cable through the hole on the bottom left

side of the controller and connect one Yellow Wire to each of the

screws marked AC and the Green Wire to GND.

NOTE

To be performed by a licensed electrician only.

Always use UL listed ½" (13 mm) conduit with male adapter

when installing AC wiring. Pro-C/PCC controllers are intended

to be supplied AC power with a 15A rated overcurrent

protected device.

Outdoor Cabinet

1. Route AC power cable and conduit through the ½" (13 mm)

conduit opening on the left side of the bottom of the cabinet.

2. Connect the wires to the transformer wires located inside the

junction box. International units are supplied with a built in

terminal strip. Always use a UL listed conduit ½" (13 mm) male

adapter when installing the AC wiring.

3. Insert the adapter into the ½" (13 mm) hole at the bottom of the

controller. Attach a nut to the adapter inside the enclosure.

4. Connect a 9-volt alkaline battery (not included) to the battery

terminals and place in the battery compartment in the front

panel. The battery allows the user to program the controller

without AC power. Watering will not occur without AC power.

Since this controller has non-volatile memory, the program

clock and calendar will be retained during a power outage even

if no battery is installed.

 GND

(Green)

 AC1

(Yellow)

 AC2

(Yellow)

 



120 V 230 V

U.S.A. INTERNATIONAL

Outdoor Cabinet

 GROUND

(Green)

 NEUTRAL

(White)

 HOT

(Black)

Indoor Cabinet

Connecting Station Wires

1. Route valve wires between control valve location

and controller.

2. At valves, attach a common wire to either solenoid wire

of all valves. This is most commonly a white colored wire.

Attach a separate control wire to the remaining wire

of each valve. All wire splice connections should be

done using waterproof connectors.

3. Route valve wires through the conduit and attach conduit

to one of the openings on the bottom of the cabinet.

4. Strip ½" (13 mm) of insulation from ends of all wires.

Secure the valve common wire to “COM” (Common) terminal.

Attach all individual valve control wires to the appropriate

station terminals.

COM

Other manuals for Pro-C

Table of contents

Other Hunter Controllers manuals

Hunter

Hunter Hydrawise Pro-HC Quick start guide

Hunter

Hunter EC User manual

Hunter

Hunter Hydrawise HC-1200M User manual

Hunter

Hunter PRO-C Hydrawise Parts list manual

Hunter

Hunter Genesis User manual

Hunter

Hunter Hydrawise HC-1200M User manual

Hunter

Hunter WVC Operating instructions

Hunter

Hunter VSX User manual

Hunter

Hunter SpectraProbe XE Instructions for use

Hunter

Hunter ICC2 User manual

Hunter

Hunter Hydrawise Pro-HC User manual

Hunter

Hunter X-CORE User manual

Hunter

Hunter ICC Series User manual

Hunter

Hunter ICC2 User manual

Hunter

Hunter SRC Plus Installation and operation manual

Hunter

Hunter Hydrawise HC-1200M User manual

Hunter

Hunter Hydrawise HC-1200M User manual

Hunter

Hunter 27206 User manual

Hunter

Hunter X-CORE XC-800I Operating instructions

Hunter

Hunter HCC Installation manual

Hunter

Hunter X-CORE XC-2 Parts list manual

Hunter

Hunter NODE-100 User manual

Hunter

Hunter ACC2 Installation manual

Hunter

Hunter Pro-HC601-A User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual